What did you do to your truck today? Chapter II

[66clow]

Originally Posted by 72_swb

I put the new flex plate and starter on. Went with the 98 delco truck starter.
I adjusted my head lights and and went for a cruise.

Is that a small starter? Is it a high torque starter? For what engine?

[Barnfind46]

Swapped out the back glass rubber for a used one with the stainless trim.I bought a back glass with trim for $20.00 at my local pick and pull.My back glass was in better shape so I just used the rubber and trim.

[ohboy321]

Today I pulled the old JVC radio out to see if the dash had been hacked up by any of the previous owners. It was nice to see that it wasn't. I will get an original looking radio some day.

This week I ordered pins and bushings to rebuild the door hinges, as well as a NOS door stop retainer to replace one that is missing.

[72_swb]

Originally Posted by 66clow

Is that a small starter? Is it a high torque starter? For what engine?

yes its a smaller starter. I think they may consider them high torque mini. not sure on that. We used one a 468 13 to 1 motor. Im not sure when gm started using them? I just order a starter for a 98 1/2 ton 350. Used them on several cars now. It was 210 from the chevy house. half the weight and size of the old starters.

[firedemon]

spent the evening on the internet researching roller motor with mechanical fuel pump realize I need a better job or a good lotto win

[74baggedbug]

Installed these aluminum header gaskets.. I've heard mixed reviews but worth a shot

[toolboxchev]

Originally Posted by 74baggedbug

Installed these aluminum header gaskets.. I've heard mixed reviews but worth a shot

Great looking engine and compartment!

[hewittca]

I never liked the stock location of the step bumper on my truck. It always looked too low to me. So, after doing the 2.5" frame raise in the rear, it was the perfect opportunity to tuck the bumper higher up. I think it looks much cleaner now. I was originally going to ditch this bumper for a sport bumper, but this simple step bumper is growing on me. I think I may keep it.

[dfwright]

I really like what you've done there. I have a similar bumper, and the same issue with it mounting an inch too low. I may just have to do this myself. It looks much better.

Originally Posted by hewittca

I never liked the stock location of the step bumper on my truck. It always looked too low to me. So, after doing the 2.5" frame raise in the rear, it was the perfect opportunity to tuck the bumper higher up. I think it looks much cleaner now. I was originally going to ditch this bumper for a sport bumper, but this simple step bumper is growing on me. I think I may keep it.

[Metaldoc]

Originally Posted by hewittca

I never liked the stock location of the step bumper on my truck. It always looked too low to me. So, after doing the 2.5" frame raise in the rear, it was the perfect opportunity to tuck the bumper higher up. I think it looks much cleaner now. I was originally going to ditch this bumper for a sport bumper, but this simple step bumper is growing on me. I think I may keep it.

These old bumpers look great But I'd like to raise mine an inch. My tailgate hinge points and bed are raised, when I close the gate there's a 1 1/2 gap.

[Metaldoc]

Mounted the inverter and Bluetooth, usb, sd card, 1/8 jack, FM radio install started.

[hewittca]

Originally Posted by Metaldoc

These old bumpers look great But I'd like to raise mine an inch. My tailgate hinge points and bed are raised, when I close the gate there's a 1 1/2 gap.

I love your tailgate mod. That is one of the coolest mods I've seen on this forum. I think with all the fab work you've done on your truck, you could knock out that bumper raise in no time

[Metaldoc]

Originally Posted by hewittca

I love your tailgate mod. That is one of the coolest mods I've seen on this forum. I think with all the fab work you've done on your truck, you could knock out that bumper raise in no time

Thanks it was not easy to get all of it to fit, but nothing is impossible, it's just never been done. I've done quite a few mods that only a trained eye would see.

[hamjet]

I changed out the ignition switch today. it was acting up, ( cranked fine but wouldn't start till I let off the key to run position ). All planets are once again aligned....

[BugzC10]

Installed new fuel line, filter and guage....old rubber one was clogging up filter.

[SoCoC10]

Before

[SoCoC10]

After

[Andy4639]

Worked on the Ramp Rat tonight. Got the electric washer jug plumbed and the screen in the cowl installed. Picked up some epoxy putty to start on the rebuild of the GM steering wheel tomorrow also.

[Absolute home]

Started to put body molding on, not really digging it seems cheap and flimsy. Not so much the side stuff but for sure the tailgate.

[Andy4639]

Took the old seat out and replaced with a 90 model seat. Put the drivers side harness in have to make a LQ yard run to pick up some more belts. Installed the new strob light also.

Took the hump out and sealed it up good and put more screws in it.
Got to get a rubber mat for it and the inside should be done.

You Tube

[firedemon]

Originally Posted by Absolute home

Started to put body molding on, not really digging it seems cheap and flimsy. Not so much the side stuff but for sure the tailgate.

looks good though

[SoCoC10]

Rust repair and body work is done. Got some paint on her. Custom PPG not the original "Medium Red" and not quite "Hugger Orange".

[SoCoC10]

New Goodmark bed sides.

[Canuckvetter]

http://67-72chevytrucks.com/vboard/a...1&d=1485611782

Painted my later model console fawn beige to fit in between my Procar seats in my Vermillion 67

[berch 69GMC]

Paint looks great SOCO.