|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
01-22-2017, 04:42 PM
|
#1 |
|
Registered User
Join Date: May 2008
Location: 204
Posts: 903
|
1970 Vin Plate location
Could someone take some measurements of where the holes for the vin plate on a 1970 pickup should be? �� I just need the position down from the latch indentation.
__________________
1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery |
|
|
|
01-22-2017, 05:23 PM
|
#2 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
|
Re: 1970 Vin Plate location
I get 9 3/4" from center of outer lower latch bolt hole to center of outer upper VIN-plate rivet
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
01-22-2017, 05:42 PM
|
#3 | |
|
Registered User
Join Date: May 2008
Location: 204
Posts: 903
|
Re: 1970 Vin Plate location
Quote:
__________________
1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery |
|
|
|
|
|
01-22-2017, 07:08 PM
|
#4 |
|
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,862
|
Re: 1970 Vin Plate location
Yes, I did measure my '72. I never thought about that. I guess the jamb vent makes 71-
/72s lower. I just checked a cab I have but it looks like it's a '69. Sorry for giving bad info.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
01-22-2017, 07:29 PM
|
#5 |
|
Registered User
Join Date: Oct 2012
Location: Green Valley Arizona
Posts: 1,351
|
Re: 1970 Vin Plate location
I measured 1-7/16" from the edge of the latch indentation down to the center of the left rivet
__________________
1970 C10 Short Stepper with 71/72 front clip. |
|
|
|
|
01-22-2017, 08:41 PM
|
#6 | |
|
Registered User
Join Date: May 2008
Location: 204
Posts: 903
|
Re: 1970 Vin Plate location
Quote:
__________________
1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery |
|
|
|
|
|
01-23-2017, 09:33 PM
|
#7 |
|
Registered User
 Join Date: Feb 2009
Location: Cle Elum, Washington
Posts: 163
|
Re: 1970 Vin Plate location
If you take the vin plate off for paint where do you find those funny rivets to
replace it?
__________________
cascadeheavychevy 67 C10 327 4speed 69 C20 350 4WD 4speed 69 C20 350 4WD 4speed 69 C20 350 4 soeed 69 C20 CST 350 Auto 70 C10 307 4speed 71 GMC Supr 350 Auto 70 C10 350 Auto 67 CST 327 Auto |
|
|
|
|
01-23-2017, 09:43 PM
|
#8 | |
|
Registered User
Join Date: May 2008
Location: 204
Posts: 903
|
Re: 1970 Vin Plate location
Quote:
 And they are commonly referred to as rosette rivets.
__________________
1969 Chevy Custom Camper 3/4 ton Rust free survivor 1972 Chevy Blazer CST 4x4 Almost Rust free survivor 1972 GMC Jimmy 2wd Undergoing surgery |
|
|
|
|
|
01-24-2017, 12:24 AM
|
#9 | |
|
Registered User
Join Date: Dec 2009
Location: El Dorado Ca
Posts: 3,374
|
Re: 1970 Vin Plate location
Quote:
|
|
|
|
|
|
11-14-2017, 09:54 PM
|
#10 |
|
Registered User
Join Date: Oct 2017
Location: Livermore, CA
Posts: 13
|
Re: 1970 Vin Plate location
Where are the VIN locations? I tried to register my vehicle today at DMV and was told I needed to have 2 VIN locations. I could only find the VIN plate on the door...
__________________
1970 GMC Jimmy LT1 w/Holly EFI Willwood Hydroboost |
|
|
|
|
11-14-2017, 10:45 PM
|
#11 |
|
Senior Member
Join Date: Oct 2009
Location: Godley, TX
Posts: 17,931
|
Re: 1970 Vin Plate location
There are 2 full VINs: metal tag and SPID in the glovebox. There is a partial VIN on the frame rail topside in the vicinity of the steering box.
EDIT: Would use the partial frame VIN only if the SPID didn't exist or the gb door had been changed. Also - actually check the frame VIN first if you're gonna let them see it - might be embarrassing if you learned you had a cab or frame swap in front of the little ol DMV lady. |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
