Xmas In March, Thanks To Porterbuilt. - Page 5 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jlaird · 05-12-2007, 09:39 PM

Damn, you beat me to it. Here is what I was trying to say:

jimmydean · 05-12-2007, 11:32 PM

Quote:

Originally Posted by MEANGREEN70

Well heres my drawing, I think this will work. What do you guys think? hope the drawing is clear enough.

maybe?

That's what I had in mind. If you run 1 front set and 1 rear set per tank (like left vs. right) then the compressors will se the same amount of work. If you run 1 tank for front and 1 tank for rear, the compressor running the front tank will run a lot more than the rear because of the amount of air required to lift the front.

Either way, it will be a sweet setup. But even wear is something you might consider.

Can't wait to see it all done!

MEANGREEN70 · 05-15-2007, 11:27 PM

Today i started pluming the air system, so i can see how everything is going to work. I 'll be going with different fitting when I'll get to the final assembly.

BigTruckDriver · 05-15-2007, 11:39 PM

Looks good meangreen! I think if you mount your rear shocks out side the frame you might get a better ride

MEANGREEN70 · 05-16-2007, 08:52 AM

I heard that you could use chevy impala rear brakes on this truck. If true does anybody know if theres any modnification that need to be done. I'm looking to pu rear disc brakes on my truck. thank you

jlaird · 05-16-2007, 10:13 AM

Quote:

Originally Posted by MEANGREEN70

I heard that you could use chevy impala rear brakes on this truck. If true does anybody know if theres any modnification that need to be done. I'm looking to pu rear disc brakes on my truck. thank you

http://www.67-72chevytrucks.com/vboa...ghlight=impala

http://www.67-72chevytrucks.com/vboa...ghlight=impala

jimmydean · 05-16-2007, 11:34 AM

Looks great! You are making quick work of this truck, that's awesome.

MEANGREEN70 · 05-17-2007, 10:16 PM

Finish pluming the bags today,may tomorrow I'll wire it. hopefully I can find a 67-68 front clip soon that way I can fit it , before I take the cad off and finish the frame. Here are some new pics. like always your opinion is welcome.

MEANGREEN70 · 05-17-2007, 10:22 PM

I guess I need to install one of this on each outlet from the tanks to the bags.

camaro__thunder · 05-18-2007, 04:03 AM

front bag plate compressor mounts.
no other use for them with the dropmember.

watahyahknow · 05-18-2007, 04:40 AM

im going to check back here for sure , im in the planning/buyingstage for my own system

jlaird · 05-18-2007, 09:27 AM

Quote:

Originally Posted by MEANGREEN70

I guess I need to install one of this on each outlet from the tanks to the bags.

Is this a daily driver? If not, I wouldn't bother with the water trap.

BigTruckDriver · 05-18-2007, 03:47 PM

Quote:

Originally Posted by MEANGREEN70

I guess I need to install one of this on each outlet from the tanks to the bags.

Could you install it in between the pump and the tank? If so you could keep moisture out of the tank and the bags. One thing about air filters , I think here bigger is better. You dont want a small air filter slowing down the air flow to your system.

BigTruckDriver · 05-18-2007, 03:52 PM

Quote:

Originally Posted by jlaird

Is this a daily driver? If not, I wouldn't bother with the water trap.

What might be good for one guy may not be for the other. Meaning you live in NY , meangreen in TX. I know from first hand experience moisture is a problem here in TX.

SCOTI · 05-18-2007, 05:37 PM

Quote:

Originally Posted by BigTruckDriver

What might be good for one guy may not be for the other. Meaning you live in NY , meangreen in TX. I know from first hand experience moisture is a problem here in TX.

I haven't experienced any issues w/my air set-up & I don't don't have a moisture trap. What problems have you had w/your system?

BigTruckDriver · 05-18-2007, 10:49 PM

You don't have to worry about your lines or bags. The tank is where moisture will collect. Then it will cause rust and the rust could clog up you lines. You could always put a drain on your tank and check the system every now and then. But then again to each his own ,if you don't need it you don't need it

Scotti, you running nitrogen tanks? What are you running?

MEANGREEN70 · 05-18-2007, 11:23 PM

Quote:

Originally Posted by jlaird

Damn, you beat me to it. Here is what I was trying to say:

Quote:

Originally Posted by jlaird

http://www.67-72chevytrucks.com/vboa...ghlight=impala

http://www.67-72chevytrucks.com/vboa...ghlight=impala

Quote:

Originally Posted by jlaird

Is this a daily driver? If not, I wouldn't bother with the water trap.

jlaird, I haven't gotten change to thank for all of you help. On till now so thank you.

I'm building this truck as a show truck, and maybe wkend driving ,cruise
etc.

SCOTI · 05-19-2007, 12:55 AM

Quote:

Originally Posted by BigTruckDriver

You don't have to worry about your lines or bags. The tank is where moisture will collect. Then it will cause rust and the rust could clog up you lines. You could always put a drain on your tank and check the system every now and then. But then again to each his own ,if you don't need it you don't need it

Scotti, you running nitrogen tanks? What are you running?

No nitrogen here. I'm using a small Thompson compressor.

BigTruckDriver · 05-19-2007, 11:13 AM

If you are drawing air in from the outside for your system that its likely you will get some moisture. Scotti how old is your system? Have you had a chance to look inside to SEE that you do not have moisture problems or you just saying you do not? A aluminum tank will be good also. A filter is not a necessity but just a little added insurance. On my high dollar system I would not have a problem running a cheap filter. Oh well

jlaird · 05-19-2007, 11:26 AM

Quote:

Originally Posted by BigTruckDriver

If you are drawing air in from the outside for your system that its likely you will get some moisture. Scotti how old is your system? Have you had a chance to look inside to SEE that you do not have moisture problems or you just saying you do not? A aluminum tank will be good also. A filter is not a necessity but just a little added insurance. On my high dollar system I would not have a problem running a cheap filter. Oh well

If you do decide to run a water trap, I would put it after the tank. This will assure you of the least amount of possible water in your lines/valves/bags. That is the goal right? Ok, lets hear all the opposing views... put a drain on your tanks.

SCOTI · 05-19-2007, 11:30 AM

Quote:

Originally Posted by BigTruckDriver

If you are drawing air in from the outside for your system that its likely you will get some moisture. Scotti how old is your system? Have you had a chance to look inside to SEE that you do not have moisture problems or you just saying you do not? A aluminum tank will be good also. A filter is not a necessity but just a little added insurance. On my high dollar system I would not have a problem running a cheap filter. Oh well

I've had my system in since mid '01. I've never had any problems w/it so there's not been any reason to check it (if it ain't broke... dont break it).

I'm currently upgrading my bags, suspension, & drivetrain so I have everything apart. When I've moved the tank, I didn't feel anything shifting around internally. I suppose I could remove a fitting & see if there's signs of something wrong.

BigTruckDriver · 05-19-2007, 11:40 AM

Quote:

Originally Posted by jlaird

If you do decide to run a water trap, I would put it after the tank. This will assure you of the least amount of possible water in your lines/valves/bags. That is the goal right? Ok, lets hear all the opposing views... put a drain on your tanks.

yes that too

SCOTI · 05-19-2007, 06:35 PM

I took a hammer to the tank & 'rattled' it around some. I did get some corrosion/rust pieces out of it. I wonder how long it would take to eat through a tank?

Soooooo . . ..... it would be wise to run a filter/trap; especially if your running an electronic system w/solenoids & valves (just to protect your investment). It's prob not that big of a deal on manual control systems.

watahyahknow · 05-20-2007, 02:54 AM

it should work on automated systems too since the watertrap is placed between the compressor and tank .
you now im studying for my big rig licence at the moment and those big truck have the same problem they use a "wet tank" in here the air gets compressed and the vapor condenses to the bottom and after that they distribute the compressed air intoo the other tanks with a special 4 way valve , newer trucks dont have the wet tank no more but have a special dehumidifier that looks like a oilfilter cartridge .
the little pullvalves with cords they use on trucks would be indeal for our aplycation too i believe it sure beats crawling halfway under the bed to open up the little valves on the tanks to drain the water

MEANGREEN70 · 05-20-2007, 02:52 PM

Quote:

Originally Posted by jlaird

If you do decide to run a water trap, I would put it after the tank. This will assure you of the least amount of possible water in your lines/valves/bags. That is the goal right? Ok, lets hear all the opposing views... put a drain on your tanks.

I'm with jlaird, I think they should be in the tank out port to the bags, just like your normal tool comp. I maybe wrong, but as long as you have air stored in the tanks is going to build moisture when you use it. Even if you put the trap between the comp and the tanks. Right.

05-12-2007, 09:39 PM	#101
jlaird Senior Member Join Date: May 2004 Location: johnstown, NY Posts: 2,393	Re: Xmas In March, Thanks To Porterbuilt. Damn, you beat me to it. Here is what I was trying to say:

05-15-2007, 11:27 PM	#103
MEANGREEN70 Registered User Join Date: Aug 2005 Location: SACHSE,TX Posts: 132	Re: Xmas In March, Thanks To Porterbuilt. Today i started pluming the air system, so i can see how everything is going to work. I 'll be going with different fitting when I'll get to the final assembly. Attached Images

05-15-2007, 11:39 PM	#104
BigTruckDriver Registered User Join Date: Apr 2007 Location: Dallas Posts: 156	Re: Xmas In March, Thanks To Porterbuilt. Looks good meangreen! I think if you mount your rear shocks out side the frame you might get a better ride

05-16-2007, 08:52 AM	#105
MEANGREEN70 Registered User Join Date: Aug 2005 Location: SACHSE,TX Posts: 132	Re: Xmas In March, Thanks To Porterbuilt. I heard that you could use chevy impala rear brakes on this truck. If true does anybody know if theres any modnification that need to be done. I'm looking to pu rear disc brakes on my truck. thank you Last edited by MEANGREEN70; 05-16-2007 at 08:53 AM.

05-16-2007, 11:34 AM	#107
jimmydean Registered User Join Date: May 2005 Location: Beaverton, OR Posts: 3,728	Re: Xmas In March, Thanks To Porterbuilt. Looks great! You are making quick work of this truck, that's awesome. __________________ New Project: 1966 LWB C20 Plans: 1/2 ton conversion Dropmember front Dropmember rear Corvette discs Restored raised bed http://67-72chevytrucks.com/vboard/s....php?p=4295210

05-17-2007, 10:16 PM	#108
MEANGREEN70 Registered User Join Date: Aug 2005 Location: SACHSE,TX Posts: 132	Re: Xmas In March, Thanks To Porterbuilt. Finish pluming the bags today,may tomorrow I'll wire it. hopefully I can find a 67-68 front clip soon that way I can fit it , before I take the cad off and finish the frame. Here are some new pics. like always your opinion is welcome. Attached Images

05-17-2007, 10:22 PM	#109
MEANGREEN70 Registered User Join Date: Aug 2005 Location: SACHSE,TX Posts: 132	Re: Xmas In March, Thanks To Porterbuilt. I guess I need to install one of this on each outlet from the tanks to the bags. Attached Images

05-18-2007, 04:03 AM	#110
camaro__thunder Epoxy Primer Friendly Join Date: Feb 2004 Location: South of Houston TEXXXAS Posts: 680	Re: Xmas In March, Thanks To Porterbuilt. front bag plate compressor mounts. no other use for them with the dropmember. __________________ My Project 69 SWB SHAVED BAGGED DOORED

05-18-2007, 04:40 AM	#111
watahyahknow Registered User Join Date: Jul 2006 Location: the netherlands europe Posts: 4,335	Re: Xmas In March, Thanks To Porterbuilt. im going to check back here for sure , im in the planning/buyingstage for my own system __________________ i got a job again and having fun at it too idea's for the trucks and the order of things to do are taking shape and get closer to being realized , a few more months and i be able to start building for real i complete 2 of the trucks intoo running fashion one custom and one basicly stock the thirth will be sacrificed for parts

05-18-2007, 10:49 PM	#116
BigTruckDriver Registered User Join Date: Apr 2007 Location: Dallas Posts: 156	Re: Xmas In March, Thanks To Porterbuilt. You don't have to worry about your lines or bags. The tank is where moisture will collect. Then it will cause rust and the rust could clog up you lines. You could always put a drain on your tank and check the system every now and then. But then again to each his own ,if you don't need it you don't need it Scotti, you running nitrogen tanks? What are you running? Last edited by BigTruckDriver; 05-18-2007 at 10:54 PM.

05-19-2007, 11:13 AM	#119
BigTruckDriver Registered User Join Date: Apr 2007 Location: Dallas Posts: 156	Re: Xmas In March, Thanks To Porterbuilt. If you are drawing air in from the outside for your system that its likely you will get some moisture. Scotti how old is your system? Have you had a chance to look inside to SEE that you do not have moisture problems or you just saying you do not? A aluminum tank will be good also. A filter is not a necessity but just a little added insurance. On my high dollar system I would not have a problem running a cheap filter. Oh well

05-19-2007, 06:35 PM	#123
SCOTI Registered User Join Date: Apr 2001 Location: DALLAS,TX Posts: 21,910	Re: Xmas In March, Thanks To Porterbuilt. I took a hammer to the tank & 'rattled' it around some. I did get some corrosion/rust pieces out of it. I wonder how long it would take to eat through a tank? Soooooo . . ..... it would be wise to run a filter/trap; especially if your running an electronic system w/solenoids & valves (just to protect your investment). It's prob not that big of a deal on manual control systems. __________________ 67SWB-B.B.RetroRod 64SWB-Recycle 89CCDually-Driver/Tow Truck 99CCSWB Driver All Fleetsides @rattlecankustoms in IG Building a small, high rpm engine with the perfect bore, stroke and rod ratio is very impressive. It's like a highly skilled Morrocan sword fighter with a Damascus Steel Scimitar..... *Cubic inches is like Indiana Jones with a cheap pistol.*

05-20-2007, 02:54 AM	#124
watahyahknow Registered User Join Date: Jul 2006 Location: the netherlands europe Posts: 4,335	Re: Xmas In March, Thanks To Porterbuilt. it should work on automated systems too since the watertrap is placed between the compressor and tank . you now im studying for my big rig licence at the moment and those big truck have the same problem they use a "wet tank" in here the air gets compressed and the vapor condenses to the bottom and after that they distribute the compressed air intoo the other tanks with a special 4 way valve , newer trucks dont have the wet tank no more but have a special dehumidifier that looks like a oilfilter cartridge . the little pullvalves with cords they use on trucks would be indeal for our aplycation too i believe it sure beats crawling halfway under the bed to open up the little valves on the tanks to drain the water __________________ i got a job again and having fun at it too idea's for the trucks and the order of things to do are taking shape and get closer to being realized , a few more months and i be able to start building for real i complete 2 of the trucks intoo running fashion one custom and one basicly stock the thirth will be sacrificed for parts



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.