project " little daisy" - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**FRENCHBLUE72** · 09-30-2007, 09:51 AM

Will have lots of updates with pics today spent a solid 10 hours workin on her yesterday and a couple of hours getting parts..

ChevyDude · 09-30-2007, 11:06 AM

That thing is gonna look really nice when you finish!!! Good job!!!

**FRENCHBLUE72** · 09-30-2007, 11:23 PM

Got the taillights comming hopefully they will be here sometime this week.... Heres a few pics from this weekend I think I have about 20 hours in this weekend........I resealed all the cab seams and started on the hacked up passenger side fresh air vent. Not sure what the previous owner did here but I managed to cut out a piece froma donor cab for $20..... Lots of welding and grinding involved...

**FRENCHBLUE72** · 09-30-2007, 11:28 PM

More progress of the fresh air vents almost done...

**FRENCHBLUE72** · 09-30-2007, 11:35 PM

Heres a few pics of what I scored at the yard left and right kick plates 40$ one tranny hump $25 as you can see the one on the right is hacked up pretty good. I also got the drivers side vent cover. I welded up the 4 speed hole. Also snapped a pic of the finished drivers side kick pannel.

**FRENCHBLUE72** · 09-30-2007, 11:59 PM

Got the passengerside door primed and hung,I only did the inside and jamb areas as the outside is gonna need some serious work....

**FRENCHBLUE72** · 10-01-2007, 12:01 AM

Last of the pics for tonight.....

**FRENCHBLUE72** · 11-21-2007, 10:50 AM

Im off all week so tons of progress should be had..... Finally..

my67chevytruck · 11-21-2007, 12:08 PM

Great Score.. Keep up the good work. Your hard work will payoff in the end.

**FRENCHBLUE72** · 11-23-2007, 01:20 PM

Well yesterday was like takeing a few steps back. I fired up the compressor and blew the hose so I had to fix that.. Cleaned the shop up and busted out the sawz all so that I could cut out a small section where the driveshaft was rubbing when you hit a bump. Dropped out the driveshaft and proceded to notch crossmember and they it happened I see fluid and think wtf did I cut gas ? brake line so I stop the saw and run for a bucket. Turns out the brake line runs accross the crossmember and it was so dirty I did not see it. Then I proceded to pop off the diff cover to change out the rear fluid and check to see if there really was a posi back there???? guess what no posi not really a big deal but I hate liars... So I get the rear end buttoned up and put the drive shaft back in and fire her up gonna move her out so I can take some pics she runs great and the after getting warmed up she dies crap.... So I check out everything and damned if shes not outta gas so into town I go... Hopefully today will be more productive... wish me luck..

Frizzle Fry · 11-23-2007, 01:51 PM

Work through that $h!t and don't let anything stop you. We've all had days like that, or worse. That truck is going to be so nice and I'm seriously jealous!

corn · 11-24-2007, 04:00 PM

Sweet project!

**FRENCHBLUE72** · 11-26-2007, 11:07 AM

Got all the door hardware out of the packages and lined for right and left doors. I got the father-in law over to help with shooeting the primer

thats a first for him and he did pretty well. He also shoot primer on the inner cab repairs and then he started feeling funny I told him to wear the mask..

**FRENCHBLUE72** · 11-26-2007, 11:16 AM

I got all the door hardware installed and now both doors open and close and you dont have to use a screw driver

The new door strikers are in and what a pain in the azz they were to align.

to who ever took it apart you made me

Also anyone know where these bumpers may go?

**FRENCHBLUE72** · 11-26-2007, 11:29 AM

Got the glove box door and lock installed and found a cardboard glove box that I am pretty sure is wrong. I also got the guages working and the guage lights to work

The best I can say about the wireing is

from the radio shackon the wrong end of town today its gonna say

as I got some wireing stuff from some other projects that I can use..

**FRENCHBLUE72** · 11-26-2007, 11:35 AM

Heres a pic of the new wireing fuse box that is going in. I also got the sandblaster to work and blaster a headlight bucket and a plate the bolts to the passengerside kick pannel. I also got the fuel filler picked out and ready to install as soon as the rear tank kit gets here.

**FRENCHBLUE72** · 11-26-2007, 11:41 AM

Headlight bucket installed and newly powdercoated plate. I also manages to get the headlights and parking lights to work off the old harness anyways ...

**FRENCHBLUE72** · 11-26-2007, 11:45 AM

Can anyone tell me what these holes along the back of the cab floor are for? And I found this know hideing under the dash I know it goes to the wipers but it looks to be a cable of some sort any ideas?

**FRENCHBLUE72** · 11-26-2007, 11:50 AM

I also got the fubared hole in the floor welded up and the new tranny cover installed. Also I need to come up with a cover for the master cylinder, I think I m also gonna have the shifter cable come up through this hole.

**FRENCHBLUE72** · 11-26-2007, 11:54 AM

I got the power seats mocked up and the brake line that I cut fixed.... Now back to the shop I go...

**FRENCHBLUE72** · 11-27-2007, 10:10 AM

Working on wireing today.....yep you guess it ..it sucks..

**FRENCHBLUE72** · 12-24-2007, 07:55 AM

The wireing on this trucks sucks so im gonna have to order a kit for it.. But heres what we have done in the past few days.. Replaced the tilt harness and installed the b@m shifter..

**FRENCHBLUE72** · 12-24-2007, 08:08 AM

Got the door hung and primed and thats about it...

**FRENCHBLUE72** · 12-24-2007, 08:14 AM

Heres a few shots of her outside finally in mostly one piece.

**FRENCHBLUE72** · 01-01-2008, 04:37 AM

Got a few things done today I repaied some of the rust on the lower door hinge pocket cover. I got the headlight bucket glass beaded and powder coated black. My new chrome headlight rings came in also but I need a headlight adjusting screw. The guy at auto zone just glazed over when I asked him about the plastic tabs for a 56 chevy headlight adjuster.

09-30-2007, 09:51 AM	#26
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Will have lots of updates with pics today spent a solid 10 hours workin on her yesterday and a couple of hours getting parts.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

09-30-2007, 11:06 AM	#27
ChevyDude Senior Member Join Date: Jun 2003 Location: Westminster, CO Posts: 3,071	Re: project " little daisy" That thing is gonna look really nice when you finish!!! Good job!!! __________________ Alex 1971 Lil' Red 350 SBC 700R4

09-30-2007, 11:23 PM	#28
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Got the taillights comming hopefully they will be here sometime this week.... Heres a few pics from this weekend I think I have about 20 hours in this weekend........I resealed all the cab seams and started on the hacked up passenger side fresh air vent. Not sure what the previous owner did here but I managed to cut out a piece froma donor cab for $20..... Lots of welding and grinding involved... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

09-30-2007, 11:28 PM	#29
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" More progress of the fresh air vents almost done... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

09-30-2007, 11:35 PM	#30
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Heres a few pics of what I scored at the yard left and right kick plates 40$ one tranny hump $25 as you can see the one on the right is hacked up pretty good. I also got the drivers side vent cover. I welded up the 4 speed hole. Also snapped a pic of the finished drivers side kick pannel. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

09-30-2007, 11:59 PM	#31
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Got the passengerside door primed and hung,I only did the inside and jamb areas as the outside is gonna need some serious work.... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

10-01-2007, 12:01 AM	#32
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Last of the pics for tonight..... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. Last edited by FRENCHBLUE72; 10-01-2007 at 12:08 AM.

11-21-2007, 10:50 AM	#33
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Im off all week so tons of progress should be had..... Finally.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-21-2007, 12:08 PM	#34
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: project " little daisy" Great Score.. Keep up the good work. Your hard work will payoff in the end. __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

11-23-2007, 01:20 PM	#35
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Well yesterday was like takeing a few steps back. I fired up the compressor and blew the hose so I had to fix that.. Cleaned the shop up and busted out the sawz all so that I could cut out a small section where the driveshaft was rubbing when you hit a bump. Dropped out the driveshaft and proceded to notch crossmember and they it happened I see fluid and think wtf did I cut gas ? brake line so I stop the saw and run for a bucket. Turns out the brake line runs accross the crossmember and it was so dirty I did not see it. Then I proceded to pop off the diff cover to change out the rear fluid and check to see if there really was a posi back there???? guess what no posi not really a big deal but I hate liars... So I get the rear end buttoned up and put the drive shaft back in and fire her up gonna move her out so I can take some pics she runs great and the after getting warmed up she dies crap.... So I check out everything and damned if shes not outta gas so into town I go... Hopefully today will be more productive... wish me luck.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-23-2007, 01:51 PM	#36
Frizzle Fry Registered User Join Date: Aug 2005 Location: Hillsboro Oregon Posts: 6,449	Re: project " little daisy" Work through that $h!t and don't let anything stop you. We've all had days like that, or worse. That truck is going to be so nice and I'm seriously jealous!

11-24-2007, 04:00 PM	#37
corn Registered User Join Date: Dec 2003 Location: here Posts: 5,789	Re: project " little daisy" Sweet project!

11-26-2007, 11:07 AM	#38
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Got all the door hardware out of the packages and lined for right and left doors. I got the father-in law over to help with shooeting the primerthats a first for him and he did pretty well. He also shoot primer on the inner cab repairs and then he started feeling funny I told him to wear the mask.. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. Last edited by FRENCHBLUE72; 11-26-2007 at 11:08 AM.

11-26-2007, 11:16 AM	#39
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" I got all the door hardware installed and now both doors open and close and you dont have to use a screw driver The new door strikers are in and what a pain in the azz they were to align. to who ever took it apart you made me Also anyone know where these bumpers may go? Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. Last edited by FRENCHBLUE72; 11-26-2007 at 11:17 AM.

11-26-2007, 11:29 AM	#40
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Got the glove box door and lock installed and found a cardboard glove box that I am pretty sure is wrong. I also got the guages working and the guage lights to work The best I can say about the wireing is from the radio shackon the wrong end of town today its gonna say as I got some wireing stuff from some other projects that I can use.. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..



Register or Log In To remove these advertisements.

11-26-2007, 11:35 AM	#41
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Heres a pic of the new wireing fuse box that is going in. I also got the sandblaster to work and blaster a headlight bucket and a plate the bolts to the passengerside kick pannel. I also got the fuel filler picked out and ready to install as soon as the rear tank kit gets here. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P.. Last edited by FRENCHBLUE72; 11-26-2007 at 11:36 AM.

11-26-2007, 11:41 AM	#42
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Headlight bucket installed and newly powdercoated plate. I also manages to get the headlights and parking lights to work off the old harness anyways ... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-26-2007, 11:45 AM	#43
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Can anyone tell me what these holes along the back of the cab floor are for? And I found this know hideing under the dash I know it goes to the wipers but it looks to be a cable of some sort any ideas? Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-26-2007, 11:50 AM	#44
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" I also got the fubared hole in the floor welded up and the new tranny cover installed. Also I need to come up with a cover for the master cylinder, I think I m also gonna have the shifter cable come up through this hole. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-26-2007, 11:54 AM	#45
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" I got the power seats mocked up and the brake line that I cut fixed.... Now back to the shop I go... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

11-27-2007, 10:10 AM	#46
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Working on wireing today.....yep you guess it ..it sucks.. __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-24-2007, 07:55 AM	#47
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" The wireing on this trucks sucks so im gonna have to order a kit for it.. But heres what we have done in the past few days.. Replaced the tilt harness and installed the b@m shifter.. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-24-2007, 08:08 AM	#48
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Got the door hung and primed and thats about it... Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

12-24-2007, 08:14 AM	#49
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Heres a few shots of her outside finally in mostly one piece. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

01-01-2008, 04:37 AM	#50
FRENCHBLUE72 PROJECT 7DEUCE Join Date: Dec 2002 Location: GRANTS PASS OR Posts: 21,590	Re: project " little daisy" Got a few things done today I repaied some of the rust on the lower door hinge pocket cover. I got the headlight bucket glass beaded and powder coated black. My new chrome headlight rings came in also but I need a headlight adjusting screw. The guy at auto zone just glazed over when I asked him about the plastic tabs for a 56 chevy headlight adjuster. Attached Images __________________ GO BIG GREEN GO DUCKS MEMBER #6377 72 k-5 daily driver 6'' lift 35'' 350-350-205 slowly getting rust free. Project "7DEUCE" check out my build http://67-72chevytrucks.com/vboard/s...d.php?t=267665 Tim Powell..R.I.P EastSideLowlife..... R.I.P..

Register or Log In To remove these advertisements.