The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Suspension

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 01-13-2011, 03:23 AM   #1
dicer
Registered User
 
Join Date: Dec 2010
Location: seattle, wa
Posts: 529
How many do their own alinements?

Just curious if anyone does there own back yard front end alinement?
Especially if its the straight axle, there is not much that can be done other than the wedges for caster, axle has to be bent for camber. Toe in using a laser and board ?
dicer is offline   Reply With Quote
Old 01-13-2011, 11:21 AM   #2
dznucks
Registered User
 
dznucks's Avatar
 
Join Date: Feb 2006
Location: Smyrna, Ga
Posts: 1,647
Re: How many do their own alinements?

I did a complete front end rebuild and I had to set my tie rod adjustment to drive it to the alignment shop.

i used a long piece of string and four jack stands. I placed a jack stand behind each rear wheel and in front of the front wheels. next I tied string between the front and back jackstands. the rear jackstands will need to be tucked under the truck so the string is forced against the back edge of the rear tire. you then take the front jack and position it such that the string just touches the front edge of the rear tire, remember that the front jack should be in front of the front tires.

At this point, the string is positioned in plane with the rear tires. you should easily see how out your tie rod adjustment is at this point. repeat for the opposite side of vehicle.
dznucks is offline   Reply With Quote
Old 01-13-2011, 07:47 PM   #3
66skylarkpost
Registered User
 
66skylarkpost's Avatar
 
Join Date: Mar 2006
Location: kearney,nebraska
Posts: 443
Re: How many do their own alinements?

i race a imca /nascar dirt stock car , so i better understand alignment . i do all my own . i have a rebco camber/caster guage with the magnetic adapter , toe plates as well as a toe stick . whats important is the specsification manuals and how to measure the heighth so you can properly adjust caster on our trucks .
__________________
'70 k-10 longbox- mid 70's drivetrain 350/350 487x heads 10.1:1 flowmasters ,35's 3.73's auburn posi ,rear shackle flip. '72 short stepside U.S. forestry truck, '73 455 buick,400 turbo,dropped 2"-4 1/4" ,3.07 posi,:'89 silverado 1500 ,OK truck ,5.7 holley tbi ,trick 700r4 3.07 auburn posi ,and my '66 skylark ,'73 centurion and my '84 monte carlo imca stock car
66skylarkpost is offline   Reply With Quote
Old 01-14-2011, 07:52 AM   #4
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
Re: How many do their own alinements?

I do all my own on everything.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline   Reply With Quote
Old 01-14-2011, 08:21 AM   #5
LONGHAIR
just can't cover up my redneck
 
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
Re: How many do their own alinements?

Quote:
Originally Posted by dicer View Post
axle has to be bent for camber.
That is not so, there are tapered shims that go between the spindle and knuckle for that....but if you need that, the axle is already bent or you have a bad ball-joint.
__________________
You can review the site's rules here.



Quote:
Originally Posted by Longhorn Man View Post
As for reading directions...
The directions are nothing but another man's opinion.
Learn from the mistakes of others, you won't live long enough to make them all yourself...

Bad planning on your part does not necessarily constitute an instant emergency on my part....

The great thing about being a pessimist is that you are either pleasantly surprised or right.
LONGHAIR is offline   Reply With Quote
Old 01-14-2011, 12:07 PM   #6
vin63
It's Better With Nitro
 
vin63's Avatar
 
Join Date: Apr 2008
Location: Chino Hills, CA
Posts: 2,261
Re: How many do their own alinements?

Quote:
Originally Posted by dicer View Post
Just curious if anyone does there own back yard front end alinement?
Especially if its the straight axle, there is not much that can be done other than the wedges for caster, axle has to be bent for camber. Toe in using a laser and board ?
I do the alignments on my hot rods and race cars...I use a mechanical toe-in gauge, a tape measure, and a bubble caster/camber gauge.
__________________
1963 C-10: Deluxe-optioned cab, shortbed, fleetside
Pontiac 462 ci, Kauffman D-Port alum. heads
4L80E, narrowed sheetmetal Ford 9-inch
Tubular front and rear suspension
Custom 6-piston front disc and 4-piston rear disc brakes

Last edited by vin63; 01-14-2011 at 01:24 PM.
vin63 is offline   Reply With Quote
Old 01-14-2011, 01:18 PM   #7
dicer
Registered User
 
Join Date: Dec 2010
Location: seattle, wa
Posts: 529
Re: How many do their own alinements?

So with the string set up how close was it?

Last edited by dicer; 01-14-2011 at 01:21 PM.
dicer is offline   Reply With Quote
Old 01-14-2011, 08:16 PM   #8
cparman
sharp as a marble
 
Join Date: Jan 2007
Location: atlantic beach,florida
Posts: 1,082
Re: How many do their own alinements?

I own an auto repair shop. When my ' car guys ' bring me their cars, it is nice that they have it 'CLOSE' iT MAKES OUR JOB EASIER. Without a camber/caster gauge IMO you could get close, but still could have a pull or a pending tire wear problem. I would try and get it close and take it to a traditional repair shop to get it aligned, just to make sure you were where you need to be. If you go to the mass merchandiser ( tire store chains ) you probably will get the " we do not know how to do your old truck" remark.


Quote:
Originally Posted by dicer View Post
So with the string set up how close was it?
cparman is offline   Reply With Quote
Old 01-17-2011, 07:59 AM   #9
dznucks
Registered User
 
dznucks's Avatar
 
Join Date: Feb 2006
Location: Smyrna, Ga
Posts: 1,647
Re: How many do their own alinements?

The string trick was not a complete alignment fix. It was to get it "good enough" to get it to the alignement shop after a complete front end rebuild.

It drove very striaght and didnt pull at all. I painted the new tie rods and adjuster sleeves, before the alignment. I was able to tell how much they adjsuted it, which wasnt more than a full rotation of the adjuster sleeve on either side.

in doing this, i also noticed that my drivers side rear tire wasnt straight, but the passenger rear tire was. This wouldnt have been caught at the alignment shop since they dont (usually) check the rear wheels.
dznucks is offline   Reply With Quote
Old 01-17-2011, 11:49 AM   #10
kev2809
low n' slo
 
kev2809's Avatar
 
Join Date: Mar 2009
Location: rosenberg, texas
Posts: 5,129
Re: How many do their own alinements?

how does the rear tires get not straight? maybe thats something i need to look out for..
__________________
67 1/2 ton Suburban - Project DRGNWGN. Build thread

-_--_--_ _________
_--_-_ -/____|__|__\__
,.,,,.,.,,.,|_O _______ O_]
kev2809 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:18 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com