Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
|
02-09-2010, 08:43 PM | #1 |
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
dana 44-5F closed knuckle front end
Anyone know where to get replacement parts for this diff. Looking for knuckle seals, gaskets etc. Thanks
|
02-09-2010, 09:01 PM | #2 |
Registered User
Join Date: Jan 2010
Location: GREENEVILLE TENNESSEE
Posts: 1,311
|
Re: dana 44-5F closed knuckle front end
If you do have the closed knuckle front 44 you are better off ordering the front knuckle seals for a 1968 1970 jeep wagoneer...gladiator...ect i got mine from jc whitney..for my 69 K/20 front c/k 44 and these are the same parts...fit perfect
Last edited by 70BLAZERX2; 02-09-2010 at 09:02 PM. |
02-09-2010, 09:06 PM | #3 |
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
Re: dana 44-5F closed knuckle front end
Thanks, I'll check them out.
|
02-09-2010, 09:09 PM | #4 |
Registered User
Join Date: Jan 2010
Location: GREENEVILLE TENNESSEE
Posts: 1,311
|
Re: dana 44-5F closed knuckle front end
I know its wierd, but this way you can get them...and they were not that much anyway...it is still a dana44 no matter what it was in,unless a ford front then its reverse rotation high pinion.
|
02-09-2010, 10:07 PM | #5 |
Registered User
Join Date: Feb 2010
Location: Nanticoke, Pa.
Posts: 12
|
Re: dana 44-5F closed knuckle front end
Found them thanks again. Anything else on the knuckle I should get. I never took one apart, I only worked on 44's with ball joints 1975 up.
|
02-10-2010, 01:31 PM | #6 |
Registered User
Join Date: Jan 2010
Location: GREENEVILLE TENNESSEE
Posts: 1,311
|
Re: dana 44-5F closed knuckle front end
get an older book for the 68-70 trucks..I do have some of them if you cannot find them..I could e-mail you some exploded pics if needed..I have a factory service manual for these trucks
|
02-10-2010, 09:39 PM | #7 |
Senior Member
Join Date: Jul 2004
Location: Clarks Hill, Indiana
Posts: 733
|
Re: dana 44-5F closed knuckle front end
i picked up a book called the chevy owners bible, or something similar to that. I was the most info on a closed knuckle axle i had seen at the time.
__________________
1969 K10 - V8, 465, 205, 12 bolt, D44 2002-current 1969 K20 - V8, 465, 221, Eaton, D44 2012-current Nothin' but drums on all 4 corners! past horses in the stable 72 C10-short step (97-02), 68 C10-long fleet (06-12) |
02-11-2010, 06:36 PM | #8 |
Firefighter
Join Date: Feb 2001
Location: Yellville, Ar, USA
Posts: 1,943
|
Re: dana 44-5F closed knuckle front end
Try www.quad4x4.com Part #QU40188
__________________
'72 Chevy SWB 350 Auto '67 GMC LWB 350 4 speed '70 Chevy 4x4 Stepside 350 Auto Yellville, Ar. USA |
02-12-2010, 02:47 AM | #9 |
Registered User
Join Date: Feb 2010
Location: Santa Clara Utah
Posts: 85
|
Re: dana 44-5F closed knuckle front end
Is there a any difference in the dana 44 open knuckle front axles? My 72 k10 has the dana 44 with -5F in the lower right hand corner. My dads 72 k5 blazer has 44 in the lower right hand corner. Are they different?
__________________
1972 K10 4wd Swb 350, 4 speed, 205 t-case Sold 1971 Cheyenne 2wd Lwb 350 4 speed Sold 1972 K5 blazer 4WD auto A/C |
Bookmarks |
|
|