Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
12-09-2018, 05:06 PM | #1 |
Registered User
Join Date: Feb 2018
Location: wellington,kansas
Posts: 8
|
two piece driveshaft yoke
I have a yoke that needs go be replaced on my C20,,,,,it's the one that goes on right after the Carrier/Support Bearing,,,,,it has about 10 splines and is held on by a bolt in the center,,,,there's a number cast on to it #3740097.I wondered if they still make or reproduce this????
|
11-20-2022, 01:33 AM | #2 |
Registered User
Join Date: Jul 2015
Location: Vacaville CA
Posts: 153
|
Re: two piece driveshaft yoke
I was searching for a vendor that sells this center bearing position yoke but can't seem to find anyone that carries them. Anyone know if anyone is making and/or selling these?
|
11-20-2022, 09:29 AM | #3 |
Registered User
Join Date: Oct 2015
Location: IN
Posts: 208
|
Re: two piece driveshaft yoke
Base on info I found the Dana Spicer 2-4-1921 is the same, but looks like most places don't have it in stock or say obsolete.
Here's more info on it. http://www.northerndrivetrain.com/pr...-2-4-1921.html |
11-20-2022, 11:51 AM | #4 |
Registered User
Join Date: Jul 2015
Location: Vacaville CA
Posts: 153
|
Re: two piece driveshaft yoke
Yes I was running into the same, no longer available. Mine has cracks where the c clips go in and I would like to find a new one but it may not be possible.
|
11-20-2022, 12:10 PM | #5 |
Senior Member
Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: two piece driveshaft yoke
I think this is what your looking for ?
__________________
1967 Factory short bed - Old school '71 - 350 / 4bolt / 487 heads / Edelbrock C3BX Muncie M-22 4 speed / Hurst Comp plus Factory 12 bolt posi 3.73 / 255-70-15 Smoothed firewall / Factory cowl induction Power disc brakes / power steering / 3.5-5" drop |
11-20-2022, 03:51 PM | #6 |
Post Whore
Join Date: Feb 2016
Location: Portland Oregon
Posts: 10,804
|
Re: two piece driveshaft yoke
It's possible there is a difference between the C10 and the C20's. With all the folks converting to one piece drive lines there should be some good used ones around. Take a look in the classified ads.
Or better yet get your premium membership going and post a want to buy ad.
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help. RIP Bob Parks. 1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo If it breaks I didn't want it in the first place The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377 |
11-21-2022, 01:58 AM | #7 |
Registered User
Join Date: Jul 2015
Location: Vacaville CA
Posts: 153
|
Re: two piece driveshaft yoke
Thanks all for the input! I was hoping it would be something available new but it seems they are made of that special material unobtanium. I'll be looking for a good used one after I speak with the drive line shop, maybe they have a source? I installed the CPP rear slip drive shaft and poly center bearing and now I have a bad vibration so I think it needs to be balanced and when it is at the shop I'll have them try to cross reference the yoke.
|
11-21-2022, 02:27 AM | #8 |
Registered User
Join Date: Mar 2015
Location: washington
Posts: 2,159
|
Re: two piece driveshaft yoke
I have one. PM me. For family reasons I only have Monday to respond to any PM's.
|
Bookmarks |
|
|