The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Forums > Alternate Tinkerings

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-30-2017, 10:45 AM   #1
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
67 Camaro Build

Short back story to start the 67 Camaro build. We acquired this project car in June 2011, previous owner had had enough Camaro fun and listed it in the local online classifieds. Hereís what the car looked like in September 2007 about the time the PO purchased it. From the ad copy it sounds like it was in need of some metal work, which is exactly what the PO started with a local shop.
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 11-30-2017, 10:46 AM   #2
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

After a bunch of $$$ (according to the PO during our negotiations) and the shop closing its doors the Camaro was left in mid metal repair. Hereís how it looked when we found it.
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 11-30-2017, 10:50 AM   #3
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

New two-piece floor, new trunk floor, both lower front fenders, front window channel and some right rocker repairs have been completed.
Attached Images
     
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 11-30-2017, 04:39 PM   #4
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

Man, she has had a lot of metal work done to her. I'm in to follow this, it's going to be sweet.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-03-2017, 09:52 AM   #5
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Thanks Ryan I hope so!




Car came with lots of parts here’s a few pics of the piles… Took several loads to get it all to our place.
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-03-2017, 12:06 PM   #6
Clyde65
1965 Chevy C10, 2005 4.8L/4l60
 
Clyde65's Avatar
 
Join Date: Aug 2004
Location: DFW Texas
Posts: 7,828
Re: 67 Camaro Build

Big project right there, hopefully all the metal work is done to your satisfaction!
My buddy had 6 or 7 of these when We were kids....iirc, he built them all with his dad and then sold them off to fund his college.


Good luck and great project!!
__________________
Clyde65

Rebuild of Clyde
http://67-72chevytrucks.com/vboard/s...84#post8338184

69 Aristocrat Lo Liner build
http://67-72chevytrucks.com/vboard/s...84#post7561684



support our troops!
Clyde65 is offline   Reply With Quote
Old 12-06-2017, 10:34 AM   #7
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Thanks Clyde65, whatís been done looks pretty good so one of our first moves is going to be inspecting that work again to refresh the memory. You know a good friend of mine also restored a pair of 69ís back in the day, both were big block cars and if I remember correctly it paid for (or darn close) his house that they still live in today.



Once the car got here it went to the media blaster. Only damage that weíve found not caused by rust and earlier body work is this spot on the left rear inner structure next to the quarter window.
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-06-2017, 03:49 PM   #8
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

Nice. The less rust repair the better! Have any plans for solid sub frame mounts or sub frame connectors etc?
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-09-2017, 10:57 PM   #9
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

I agree that would be nice! Perhaps or polyurethane (?), sub frame connectors for sure.


Hit it with the DA, bolted on some wheels and pushed it outside for some pics, looked pretty good from a few feet away. Here’s some close ups, plenty of area’s that still need attention.
Attached Images
     
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-09-2017, 11:00 PM   #10
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Car is getting full rear quarters, mini tubs, tail pan, etc., etc., etc.
Attached Images
     
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-11-2017, 11:07 AM   #11
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Shortly after that last round of pics we tore the car back down to a shell, Iíd no idea it would be a little over 5 years to get back to it.
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-11-2017, 04:34 PM   #12
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

Man, I'm so jealous. I can't leave anything bare metal for that long without doing more work.

Do you plan to race this car ot will it just be a tribute car? From the research I've done on the bushings, the polys still flex a bit. So racers recommend solid ones. I plan to auto cross mine so I think I'm going solid on it.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-13-2017, 10:34 AM   #13
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Oh no, donít be jealous, best way to describe the next maneuver is stupid is as stupid does... Yes, and no, not a dedicated race car (no roll cage) but a very fun street car with some time slips in the glove box!


Hereís pics of us pulling it out of storage a few months ago, some dingus (me?) put it away without sealing it up.
Attached Images
   
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-13-2017, 10:41 AM   #14
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Itís sporting a presidential tan these days!
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-13-2017, 05:46 PM   #15
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

Are you going to spray acid on it or a rust converter or just sand it off? It still doesn't look bad though.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-15-2017, 04:08 PM   #16
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Itís not that bad and would sand off (flash rust), probably will end up sanding some areas but with it getting rear quarters, etc. Itíll probably get media blasted one more time after weíre done with all the metal repairs.



I did have a red on red 67 Camaro (327, glide, 10 bolt) back in high school for a short time. Always wanted a 67 Camaro, big block, 4-speed day two-ish type drag car. The plan has always been a tribute car to Grumpyís Toy III. Donít know if weíll actually letter the car but I like everything about one of the first big block Camaroís. Hereís some picís of the actual restored car owned by the Mecumís and back in the day with Daí Grump & George Hurst.
Attached Images
     
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-15-2017, 04:43 PM   #17
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

That will be really cool. I want another 4 speed car to drive around too. I miss it so bad!
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-20-2017, 10:52 AM   #18
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Thanks Ryan, banging gears is a pretty good time!



For the purists, and itís just interesting to know how this particular Camaro was originally equipped when it left the factory, the dealer, who bought it and the delivery date (just had a B-Day).

Trim tag is still in place and we have the protect-o-plate, after decoding both and verifying itís not anything really special (nice colors) I donít feel bad about making into something better, IMO.

Trim Tag:
11 = Nov. B = 2nd Week R830 = Los Angles Plant Code#
ST 67- = 1967 12637 = Coupe, custom int. LOS = Van Nuys, CA. 8297 = Body #
TR 797-Z = Parchment custom buckets H-H = Mountain Green
W = Tinted Windshield 2G = Center Console 3K = RPO Z21, style trim group

Protect-O-Plate:
K = Parchment/Black (Carpet, instrument panel, and steering wheel are black)
HH = Mountain Green / Mountain Green
123377Lxxxxxx 1 = Chevrolet, 2 = Camaro, 3 = for 6-cylinder engine, 37 = coupe, 7 = 1967 model, L = Los Angeles, CA. xxxxxx = vehicle serial number sequence
B = Bay City (1 bbl/2 bbl))
F0922LN = F for Flint (MI) Motor Facility (L6 engines), 09 = month of year, 22 = day of month, LN = eng suffix code (without K19 (smog) 250ci/155HP L22 L6, 3- or 4-spd trans, no-A/C
PA1107G PA = 3.08 Ratio, 10 Bolt axle, 8.125 in. diameter ring gear, Non Ė Positraction, Standard Brake 11 = month of year, 07 = day of month, G = Detroit Gear & Axle plant
K = November 1966
S7P09 = Saginaw Manual 3-speed
Attached Images
     
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-20-2017, 04:43 PM   #19
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

Very cool! I just got a 71 RS and I've been trying to find the build sheet to verify it is an RS. I only have 1 place left to look and I hope it's there. Other wise oh well. It's just a 307/PG car so it wouldn't be worth what a big block car would be. Haha
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 12-22-2017, 01:58 PM   #20
rgunlock
Senior Member
 
rgunlock's Avatar
 
Join Date: Jul 2009
Location: Tomball, Texas
Posts: 1,224
Re: 67 Camaro Build

Just found that you'd started this thread. I'll be following. I drove a '69 Camaro my Sr. year and through college. Would love to get another one. For now I'll have to live vicariously through your build.
__________________
Rick

78 GMC K15 SWB, 350/NV4500/NP205/4.10s Project Thread
59 Chevy SWB Stepside (next in line)
rgunlock is offline   Reply With Quote
Old 12-23-2017, 12:05 PM   #21
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Quote:
Originally Posted by Dieselwrencher View Post
Very cool! I just got a 71 RS and I've been trying to find the build sheet to verify it is an RS. I only have 1 place left to look and I hope it's there. Other wise oh well. It's just a 307/PG car so it wouldn't be worth what a big block car would be. Haha
Congrats good for you, I really like the RS frontend on second gens! Hope you find it, we have the build sheets for Blue and our C10, that stuff is just cool.

Quote:
Originally Posted by rgunlock View Post
Just found that you'd started this thread. I'll be following. I drove a '69 Camaro my Sr. year and through college. Would love to get another one. For now I'll have to live vicariously through your build.
Thanks Rick, I always appreciate your thoughts and comments.



Using a plumb bob and making marks on the floor the subframe has passed our simple squareness test. Pulled the old body mounts and found that the left rear mount is going to need some attention, but the rest are in really great shape.
Attached Images
    
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-27-2017, 04:56 PM   #22
gringoloco
A guy with a truck
 
gringoloco's Avatar
 
Join Date: Sep 2005
Location: Utah!
Posts: 5,462
Re: 67 Camaro Build

Hey, a local Camaro build! Know where any more are hiding? We are looking for a 67-69 Camaro or 67-68 fastback Rustang
__________________
-Chris

Instagram _elgringoloco_

'70 Short-Wide How to: Ruin a perfectly good C10
Ď70 Blazer ConversionHow To: Ruin a Perfectly Good 4wd
'72 Highlander How To: Ruin a Perfectly Good K/5 (SOLD)
'72 Blazer 2WD How to: Ruin a perfectly good Blazer (SOLD)
'05 Yukon Daily Driven (not so stock) Yukon (SOLD)
Ď07 Yukon Denali (daily)

Members met list: SCOTI, darkhorse970, 67cheby, 67cheby'sGirl, klmore, porterbuilt, n2billet, Fastrucken, classicchev, Col Clank, GSFMECH, HuggerCST, Spray-Bomb, BACKYARD88, 5150, fine69, fatbass, smbrouss70, 65StreetCruiser, GAc10boy
gringoloco is offline   Reply With Quote
Old 12-27-2017, 05:50 PM   #23
ajviper
4x4 Guy
 
ajviper's Avatar
 
Join Date: Jul 2014
Location: Lakewood, Colorado
Posts: 90
Re: 67 Camaro Build

Always nice to see Gen 1 cars being brought back to life.
__________________
Chevy Runs Deep.
1956 210 LS1 TH350 3.31 Posi 12 Bolt
1969 Z/28 5.3 T56 3.73 Posi 12 Bolt
1973 Nova SS 355 TH350 2.73 Posi 12 Bolt
2000 K2500 Suburban LS 6.0 4L80 3.73 G80
2005 K2500HD CCSB LS 6.0 4L80 4.10 G80
2010 2SS/RS Camaro LS3 T56 Aqua Blue Metallic
ajviper is offline   Reply With Quote
Old 12-29-2017, 04:31 PM   #24
7dee2
Registered User
 
7dee2's Avatar
 
Join Date: May 2011
Location: Bountiful, Utah
Posts: 1,576
Re: 67 Camaro Build

Quote:
Originally Posted by gringoloco View Post
Hey, a local Camaro build! Know where any more are hiding? We are looking for a 67-69 Camaro or 67-68 fastback Rustang
You betcha Chris! Donít know of any personally but this 69 popped up on KSL a couple of days ago, https://www.ksl.com/auto/listing/4339502?ad_cid=4 might be something? Oops, and it's gone just that fast! That is where we found ours it was on KSL but they go really fast these days.

Quote:
Originally Posted by ajviper View Post
Always nice to see Gen 1 cars being brought back to life.
Thanks ajviper!




Time to say good bye to the wood cart its done its job and itís just way to wobbly so, up, up and away! Using the same plumb bob technique and making marks on the floor the shell also passed the high-tech squareness test. While doing this and looking closely at all the alignment holes (firewall & frame rails) they are all original and mounted to original inner panels which have not been removed by any previous work.
Attached Images
     
__________________
Brett
67 Camaro SS Build:http://67-72chevytrucks.com/vboard/s...d.php?t=751594
72 Cheyenne/K30 Super 133" DRW Build:http://67-72chevytrucks.com/vboard/s...d.php?t=645614 YouTube: https://www.youtube.com/channel/UCbN...aQ6fWWMHOi4K4g
72 Cheyenne/10 Super 115" Fleetside (Project),72 Custom/30 133" Flat Bed DRW (DD)
7dee2 is offline   Reply With Quote
Old 12-29-2017, 05:44 PM   #25
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Prairie City, Ia
Posts: 15,160
Re: 67 Camaro Build

Man, using the hoist is cheating, but I really like it. Maybe I could use a drive on to lift bodies off just like you did?
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:33 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com