The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > LSx Swaps

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-24-2018, 09:59 PM   #1
skymangs
Registered User
 
skymangs's Avatar
 
Join Date: Apr 2010
Location: Warrensburg, MO
Posts: 2,690
2000 corvette 4L60E question

I have a 4L60E from a 2000 vette that I wish to put in my 70 c10. As you know 2000 vettes did not use a tailshaft housing, so I bought one, with a vss, or so I thought. Now my mechanic is asking me how the vss connects to the tailshaft. I don’t have a friggin clue, so I turn to you. How do I make a 2000 vette 4L60 work in a c10?
skymangs is offline   Reply With Quote
Old 11-24-2018, 10:30 PM   #2
AussieinNC
Moderator
 
AussieinNC's Avatar
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,152
Re: 2000 corvette 4L60E question

The VSS is installed into the transmission case...not anywhere near the tailshaft...but you have bigger challenges ahead of you.

2000 Corvettes use a torque tube drive with the trans mounted directly to the differential unit that is solidly to the rear of the Corvette chassis. The rear end is fully independent, not a live axle as is in a C-10.

Unless you intend to do a major rear chassis rework to install the entire rear axle assembly from a Corvette you would be better to sell the Corvette trans and source a standard rear 2 wheel drive trans like a 4L60e or better still a 4L80e.

Both will require an electronic trans controller.

You could also look at a T700R4 but it should receive a major rebuild and upgrade before you install it...
Attached Images
 
__________________
Family and country before all others...

2006 Chevy Silverado (Daily Driver)
2012 Chevy Equinox

AussieinNC is offline   Reply With Quote
Old 11-24-2018, 10:53 PM   #3
skymangs
Registered User
 
skymangs's Avatar
 
Join Date: Apr 2010
Location: Warrensburg, MO
Posts: 2,690
Re: 2000 corvette 4L60E question

Quote:
Originally Posted by AussieinNC View Post
The VSS is installed into the transmission case...not anywhere near the tailshaft...but you have bigger challenges ahead of you.

2000 Corvettes use a torque tube drive with the trans mounted directly to the differential unit that is solidly to the rear of the Corvette chassis. The rear end is fully independent, not a live axle as is in a C-10.

Unless you intend to do a major rear chassis rework to install the entire rear axle assembly from a Corvette you would be better to sell the Corvette trans and source a standard rear 2 wheel drive trans like a 4L60e or better still a 4L80e.

Both will require an electronic trans controller.

You could also look at a T700R4 but it should receive a major rebuild and upgrade before you install it...
so you’re saying it’s better to use a standard 4L60E rather than try to convert the vette trans to an open type driveshaft, shoot, he’s already got it in. the reason for the vette trans is because it already has a bunch of performance upgrades.
skymangs is offline   Reply With Quote
Old 11-25-2018, 10:32 AM   #4
AussieinNC
Moderator
 
AussieinNC's Avatar
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,152
Re: 2000 corvette 4L60E question

To fit that vette trans in he would have had to install a new front bell housing assembly, new pump, new output shaft and extension housing....

Oh well...the VSS (Vehicle Speed Sensor ) simply needs either a digital style speedo or a convertor....

Maybe the problem is the trans installed no longer supports the VSS....hence his asking "How do I get a VSS to connect to the tailshaft?)

The VSS plugs into the extension housing and fits close to a reluctor wheel on the outout shaft...
See the attached pic...it shows a 4WD unit, but 2WD unit is similar...

Good luck
Attached Images
 
__________________
Family and country before all others...

2006 Chevy Silverado (Daily Driver)
2012 Chevy Equinox

AussieinNC is offline   Reply With Quote
Old 11-25-2018, 11:17 AM   #5
davepl
Registered User
 
davepl's Avatar
 
Join Date: Aug 2006
Location: Redmond, WA
Posts: 6,332
Re: 2000 corvette 4L60E question

I'm no expert but I think you need a passenger car trans from a B body or F body, but the Y body Corvette is very different.

Some trans, like the 4L80E, do not have a physical pickup for the speedo at all. Then you need to run a little computerizeds box that spins the cable for you.
__________________
1970 GMC Sierra Grande Custom Camper - Built, not Bought
1969 Pontiac 2+2 427/390 4-speed Coupe
1969 Pontiac 2+2 427/390 4-speed Convertible
davepl is offline   Reply With Quote
Old 11-25-2018, 02:19 PM   #6
skymangs
Registered User
 
skymangs's Avatar
 
Join Date: Apr 2010
Location: Warrensburg, MO
Posts: 2,690
Re: 2000 corvette 4L60E question

Quote:
Originally Posted by davepl View Post
I'm no expert but I think you need a passenger car trans from a B body or F body, but the Y body Corvette is very different.

Some trans, like the 4L80E, do not have a physical pickup for the speedo at all. Then you need to run a little computerizeds box that spins the cable for you.
i have the Dakota digital conversion box. so you’re saying a non vette trans would be a lot simpler than converting this one
skymangs is offline   Reply With Quote
Old 11-25-2018, 11:13 PM   #7
AussieinNC
Moderator
 
AussieinNC's Avatar
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,152
Re: 2000 corvette 4L60E question

Without repeating myself...please review my first post response....

To install the "vette trans" you would need to install the entire rear trans axle and torque tube system from a Corvette....back halving the chassis etc...

Much simpler to grab a 4l60E out of say a 2001 era Chevy or GMC 2wd pickup and install that....you will need a trans controller, but you would need one for the vette anyways...How were you thinking you would control the vette trans?....

What did the guy doing the work for you actually do to the trans to get it "in the truck"...

__________________
Family and country before all others...

2006 Chevy Silverado (Daily Driver)
2012 Chevy Equinox

AussieinNC is offline   Reply With Quote
Old 11-26-2018, 12:17 AM   #8
Wildkarde
Registered User
 
Join Date: Mar 2018
Location: Ardmore
Posts: 100
Re: 2000 corvette 4L60E question

As far as I know it isn't possible to convert a vette trans for use with a driveshaft. You can bolt a LT style bell housing to the front, but the rear is incompatible with any of the tailshaft housings. Not only is the bolt pattern completely different, the area between the trans and the differential on the vette trans is dry, the trans even has a water drain slot cast into it. Unless someone has come up with some really elaborate adapter plate the only way to use a vette trans in another vehicle is to use the getrag diff along with it.

Last edited by Wildkarde; 11-26-2018 at 12:59 AM.
Wildkarde is offline   Reply With Quote
Old 11-26-2018, 12:26 AM   #9
skymangs
Registered User
 
skymangs's Avatar
 
Join Date: Apr 2010
Location: Warrensburg, MO
Posts: 2,690
Re: 2000 corvette 4L60E question

Quote:
Originally Posted by AussieinNC View Post
Without repeating myself...please review my first post response....

To install the "vette trans" you would need to install the entire rear trans axle and torque tube system from a Corvette....back halving the chassis etc...

Much simpler to grab a 4l60E out of say a 2001 era Chevy or GMC 2wd pickup and install that....you will need a trans controller, but you would need one for the vette anyways...How were you thinking you would control the vette trans?....

What did the guy doing the work for you actually do to the trans to get it "in the truck"...

I have a trans controller, I was just trying to find a way around him having to pull the trans and install another.
skymangs is offline   Reply With Quote
Old 11-26-2018, 12:47 AM   #10
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,557
Re: 2000 corvette 4L60E question

Have you got pics of what he has done...I'm curious to see what he did..
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 11-26-2018, 10:36 AM   #11
skymangs
Registered User
 
skymangs's Avatar
 
Join Date: Apr 2010
Location: Warrensburg, MO
Posts: 2,690
Re: 2000 corvette 4L60E question

Quote:
Originally Posted by mongocanfly View Post
Have you got pics of what he has done...I'm curious to see what he did..
he just bolted on the tail shaft housing that I bought, it’s going behind a 401 nailhead. So I bought the bell housing and special flywheel, I even bought a firewall mounted TPS.
skymangs is offline   Reply With Quote
Old 11-26-2018, 10:39 AM   #12
skymangs
Registered User
 
skymangs's Avatar
 
Join Date: Apr 2010
Location: Warrensburg, MO
Posts: 2,690
Re: 2000 corvette 4L60E question

i just bought a stage 2 4L60E from JEGS, problem solved.
skymangs is offline   Reply With Quote
Old 11-26-2018, 10:38 PM   #13
AussieinNC
Moderator
 
AussieinNC's Avatar
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,152
Re: 2000 corvette 4L60E question

Hard to beat a 70 C-10.....

401 Hail Head

4L60e

What rear end is in it?

Build thread?

__________________
Family and country before all others...

2006 Chevy Silverado (Daily Driver)
2012 Chevy Equinox

AussieinNC is offline   Reply With Quote
Old 11-26-2018, 11:32 PM   #14
Wildkarde
Registered User
 
Join Date: Mar 2018
Location: Ardmore
Posts: 100
Re: 2000 corvette 4L60E question

I would be interested in what tailshaft housing you bought, if someone is now making a conversion housing that would make vette transmissions alot more worthwhile.
Wildkarde is offline   Reply With Quote
Old 11-27-2018, 10:46 PM   #15
AussieinNC
Moderator
 
AussieinNC's Avatar
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,152
Re: 2000 corvette 4L60E question

Its actually more than just the tail housing...

The Corvette housing rear bulkhead has multiple metal clad seal bores and O ring lands to seal the transmission to the differential housing..

There is a bore where the trans seal and differential seals are held and a thin O ring around the perimeter to seal the trans fluid inside the housing.

See pics....the Corvette 4L60e is "similar" but not the same as a "normal" 4L60e...

Attached Images
  
__________________
Family and country before all others...

2006 Chevy Silverado (Daily Driver)
2012 Chevy Equinox

AussieinNC is offline   Reply With Quote
Old 11-28-2018, 12:44 PM   #16
DieselSJ
Registered User
 
Join Date: Jun 2016
Location: Phoenix, AZ
Posts: 574
Re: 2000 corvette 4L60E question

Quote:
Originally Posted by skymangs View Post
so you’re saying it’s better to use a standard 4L60E rather than try to convert the vette trans to an open type driveshaft, shoot, he’s already got it in. the reason for the vette trans is because it already has a bunch of performance upgrades.
Yeah, you need to post up some pictures of that. The rear of the Vette trans is not compatible with just bolting on a tail housing from a non-Vette transmission.
__________________
87 R30 CC Dually, TBI 454, NV4500, zero rust barn find
87 Jeep Grand Wagoneer, 6.5 turbodiesel, 700R4
DieselSJ is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:13 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com