The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-13-2018, 03:02 PM   #1
D13
Registered User
 
D13's Avatar
 
Join Date: Feb 2007
Location: Memphis MI
Posts: 1,667
Replacing high mile bearings

I've got my flame proof undies on, so...

I picked up a straight six powered 1/2 ton a couple years back. Finally got around to getting it running, and did the work on the top of the motor -rebuilt carb, stopped the valve cover leaks, etc. Now I'm at the big one - the rear main is more running than leaking.

I'm pretty sure no one has been in the motor before. I personally have driven these motors a lot of miles with no bearing issues (never had the pan off my 400,000 mile '67 Biscayne), and I'm not hearing any bottom end issues. I'm not interested in putting significant money into the beast as I intend to sell it (only round eye in my pile) and it's a $1k truck not a $20k truck (it's an ex-road commissin truck and it literally has the 'delete every option' option). To get at that seal I'm going to have to pull the pan, most likely by jacking up the motor.

So here's the question. While I'm replacing the seal, should I spend a few bucks and replace the bearings with a set of standard bearings? My thought is that it can't hurt and may encourage the old gal to keep her oil pressure up. I'm pretty sure I have a set floating around, or can get them cheap (my other motor, where all my money goes, is .020 under on the crank, so my 'newer' purchases have been oversizes).
__________________
1987 C10 6.2 oil burner
1987 2 ton
1982 250/TH350 beater in progress
Dad's 1981 3/4 L6 3 on tree posi and no options, awaiting restoration or scrapping
77 1/2 ton 250, 3OTT, and hokey aftermarket AC
Plus a mess o' tractors
D13 is offline   Reply With Quote
Old 02-13-2018, 04:16 PM   #2
Tiger Joe
Registered User
 
Join Date: Mar 2015
Location: South of Pittsburgh
Posts: 338
Re: Replacing high mile bearings

i would say no. if there is no issue with the bearing, why change it? and if there is an issue, like some nick/scar/damage- then likely the crank would need have the same defect, so if you toss a new bearing in with an old crank, it will just eat up the new bearing
Tiger Joe is offline   Reply With Quote
Old 02-13-2018, 04:37 PM   #3
truckster
Senior Member
 
truckster's Avatar
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 3,906
Re: Replacing high mile bearings

If you don't plan to do any more than replace the bearings, I would also say no. The minute you pull one of the caps you're likely to find a reason the crank needs to come out.
__________________
If I didn't build it or fix it, it's probably not mine.

Last edited by truckster; 02-13-2018 at 11:16 PM.
truckster is offline   Reply With Quote
Old 02-13-2018, 07:41 PM   #4
YoungPup1977
Registered User
 
YoungPup1977's Avatar
 
Join Date: Jun 2015
Location: North Carolina
Posts: 176
Re: Replacing high mile bearings

How is the oil pressure ? If you pull a bearing and check it...most likely it will not look new..... Bottom up rebuild ?
__________________
1972 c10 swb 383/700r4
1972 c10 swb 496/700R4
1971 blazer 4x4 396/700R4
1972 blazer 4x4 383/700R4
1972 blazer 2wd 454/700R4
1967 Camaro RS SS
YoungPup1977 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:17 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright 1997-2013 67-72chevytrucks.com