Door pins and bushings replaced today - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**dutchmanz** · 01-08-2016, 05:56 PM

I was tired of having to slam my drivers door 4 times just to get it to close. A buddy at the local NAPA found a set of pins/bushings that he said would work. The factory plastic bushings were all but gone. The new bronze ones worked great however one pin was too short. I used the engine lift and a small ratchet strap to hold the door for me. Unbolted the door from the hinges and rolled it back. Next, drove the old pins out from the bottom and took the outer halves of the hinges off. One of the bushings fell out on its own. The other 3 came out with a light tap from the punch. Over the years I learned to push bushings in rather than try to tap them in. A simple piece of threaded rod works great for this. I lubed them up and stuck them back together with the old pins. The longer one would have worked but my pins were not worn enough to matter. After than it was a simple matter of bolting the door back on and making sure it was aligned. Fairly simple project. Part number for the kit: 675-5150

WarMonger · 01-08-2016, 06:29 PM

good info there.

hugger6933 · 01-08-2016, 06:49 PM

That is a good project for people that don't have tons of wrench time[I'm not saying you don't just stating that it is a good project] It can really make a huge difference in the way the truck feels and when a person gets it done it can make a huge difference in the way they feel about tackling a larger type project. Jim

nicklear36 · 01-08-2016, 09:50 PM

http://67-72chevytrucks.com/vboard/s...d.php?t=680781

This is a link to thread a posted earlier. Did you have a problem similar to this before fixing? This might help my cause.

**dutchmanz** · 01-08-2016, 10:57 PM

Quote:

Originally Posted by nicklear36

http://67-72chevytrucks.com/vboard/s...d.php?t=680781

This is a link to thread a posted earlier. Did you have a problem similar to this before fixing? This might help my cause.

No, my problem was the door dropped down as it came away from the latch plate. The door was not aligned perfectly so I did adjust it in a little at the bottom and out at the top. I will have to go back and move the striker plate in more later, but my weatherstripping is fresh and I need to wait for it to compress some.

01-08-2016, 05:56 PM	#1
dutchmanz Knuckle Buster, Instructor Join Date: May 2010 Location: Pantego, NC Posts: 562	Door pins and bushings replaced today I was tired of having to slam my drivers door 4 times just to get it to close. A buddy at the local NAPA found a set of pins/bushings that he said would work. The factory plastic bushings were all but gone. The new bronze ones worked great however one pin was too short. I used the engine lift and a small ratchet strap to hold the door for me. Unbolted the door from the hinges and rolled it back. Next, drove the old pins out from the bottom and took the outer halves of the hinges off. One of the bushings fell out on its own. The other 3 came out with a light tap from the punch. Over the years I learned to push bushings in rather than try to tap them in. A simple piece of threaded rod works great for this. I lubed them up and stuck them back together with the old pins. The longer one would have worked but my pins were not worn enough to matter. After than it was a simple matter of bolting the door back on and making sure it was aligned. Fairly simple project. Part number for the kit: 675-5150 Attached Images __________________ Current classic fleet: 72 K5 Blazer CST, unrestored factory Orange paint...mostly 69 C10 factory SWB, 454, TH400, Saddle tan, Rust-o-ration 53 Studebaker M35 w/331 Reo gas I-6, Air Force Strata Blue

01-08-2016, 06:29 PM	#2
WarMonger Registered User Join Date: Jan 2015 Location: Ventura, CA Posts: 818	Re: Door pins and bushings replaced today good info there. __________________ ..................... ____ .........________//__{\_____ ,,,,,,,/__(O)___//___/__(O)_/ 1970 C20 -_--_--_- ______ _--_--_- /___\|__\____ -_--_-_ \|_(0)\|__\|_(0)] 1972 K5

01-08-2016, 06:49 PM	#3
hugger6933 Registered User Join Date: Oct 2008 Location: Marianna Arkansas Posts: 7,257	Re: Door pins and bushings replaced today That is a good project for people that don't have tons of wrench time[I'm not saying you don't just stating that it is a good project] It can really make a huge difference in the way the truck feels and when a person gets it done it can make a huge difference in the way they feel about tackling a larger type project. Jim

01-08-2016, 09:50 PM	#4
nicklear36 Registered User Join Date: Jun 2014 Location: Beaverton, Oregon Posts: 196	Re: Door pins and bushings replaced today http://67-72chevytrucks.com/vboard/s...d.php?t=680781 This is a link to thread a posted earlier. Did you have a problem similar to this before fixing? This might help my cause.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.