The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-15-2011, 01:36 AM   #1
hbaublit
Registered User
 
hbaublit's Avatar
 
Join Date: Feb 2009
Location: Broussard LA
Posts: 28
Is it a good deal?

I was looking for a frame with a stepnotch already welded in and came along this one. I am not sure what the going rate is for frames. This one is boxed and z'ed. The guy wants 200 for it. I haven't seen it in person yet, but here are some pics. When I do go look at it, what should I make sure to look at?


__________________

1970 Chevy Step
hbaublit is offline   Reply With Quote
Old 10-15-2011, 01:46 AM   #2
VA72C10
VA72C10
 
VA72C10's Avatar
 
Join Date: Mar 2008
Location: Midlothian, VA
Posts: 25,269
Re: Is it a good deal?

200 is a great deal but I question the a-arms and wonder if it's square or not...

Also, the rear notch probably could use some cross bracing....

also, what motor was it set up for? Looks like big block mounts (?) which you'd have to change if you're going sbc...
__________________
Looking for a 67-72 swb or blazer project in or around VA.
VA72C10 is offline   Reply With Quote
Old 10-15-2011, 02:06 AM   #3
hbaublit
Registered User
 
hbaublit's Avatar
 
Join Date: Feb 2009
Location: Broussard LA
Posts: 28
Re: Is it a good deal?

Quote:
Originally Posted by VA72C10 View Post
200 is a great deal but I question the a-arms and wonder if it's square or not...

Also, the rear notch probably could use some cross bracing....

also, what motor was it set up for? Looks like big block mounts (?) which you'd have to change if you're going sbc...
I will have to ask on the mounts, didn't even think about that. Bracing is defiantly the plan for the notch.
As for squareness, I am assuming that you are talking where it's got the goofy square tubing welded up?
__________________

1970 Chevy Step
hbaublit is offline   Reply With Quote
Old 10-15-2011, 03:06 AM   #4
Mike Bradbury
Registered User
 
Mike Bradbury's Avatar
 
Join Date: Apr 2008
Location: San Diego California
Posts: 1,316
Re: Is it a good deal?

looks like the entire cross member is welded to the frame, that might make it kind of difficult if you need to change any component.
A arms need to go, they are too sketchy looking.
__________________
I'd rather attempt something great and fail.. than try something ordinary and succeed. Norman Vincent Peale

Project: Barn Raising http://67-72chevytrucks.com/vboard/s...d.php?t=414961

Project: 30 Be Low https://67-72chevytrucks.com/vboard/...d.php?t=830583
Mike Bradbury is offline   Reply With Quote
Old 10-15-2011, 03:12 AM   #5
VA72C10
VA72C10
 
VA72C10's Avatar
 
Join Date: Mar 2008
Location: Midlothian, VA
Posts: 25,269
Re: Is it a good deal?

Wondering if the frame is square itself....measure front to rear diagonally and from the front crossmember ends to the frame rails and from the rear of the notches to the rear frame rail....
__________________
Looking for a 67-72 swb or blazer project in or around VA.
VA72C10 is offline   Reply With Quote
Old 10-15-2011, 03:26 AM   #6
OARNGESI
Registered User
 
OARNGESI's Avatar
 
Join Date: Sep 2008
Location: CASA GRANDE AZ
Posts: 4,276
Re: Is it a good deal?

that looks a little sketchy id start with a stock frame even if its more
__________________
70 SWB STEPSIDE
70 BLAZER
09 challenger
OARNGESI is offline   Reply With Quote
Old 10-15-2011, 08:36 AM   #7
eurospec1
Registered User
 
eurospec1's Avatar
 
Join Date: Jun 2011
Location: Green Cove Springs FL
Posts: 194
Re: Is it a good deal?

Quote:
Originally Posted by OARNGESI View Post
that looks a little sketchy id start with a stock frame even if its more
Ya, i would not trust someone elses fab work for something like this, you would be much better off getting a stock frame and doing the work yourself
__________________
68 SWB Fleet 383
eurospec1 is offline   Reply With Quote
Old 10-15-2011, 08:45 AM   #8
mbgmike
Registered User
 
Join Date: Aug 2005
Location: Pasadena,Tx /Pto Pta DR
Posts: 5,415
Re: Is it a good deal?

I would pass on this. Don't like commenting on others work however I would pass on this without hesitation.
Run Forrest Run

Last edited by mbgmike; 10-15-2011 at 09:58 AM.
mbgmike is offline   Reply With Quote
Old 10-15-2011, 08:49 AM   #9
OJ1988
Just a car guy
 
OJ1988's Avatar
 
Join Date: Feb 2006
Location: New Washington, IN
Posts: 991
Re: Is it a good deal?

I would take that straight to the recycler.

There is a reason why its not under a truck.
__________________
1955 belair Blown Pro Street cruiser
1971 Camaro Pro Touring
1973 Vega Drag Car
1970 C20 tow rig
OJ1988 is offline   Reply With Quote
Old 10-15-2011, 09:54 AM   #10
cdowns
Senior Member
 
cdowns's Avatar
 
Join Date: Jan 2003
Location: daytonabeach
Posts: 22,956
Re: Is it a good deal?

yep recycler is the place for that abortion
__________________
71c-10 350/2004r/4:11 lowered3/4 longbed/dead by hurricane

MEANING OF DEATH::::: SOMEBODY ELSE GETS YOUR STUFF

DONT BELIEVE EVERYTHING YOU THINK

TAKE MY ADVISE;I DON'T USE IT ANYWAY
cdowns is offline   Reply With Quote
Old 10-15-2011, 10:59 AM   #11
bcutt
Registered User
 
bcutt's Avatar
 
Join Date: Aug 2008
Location: North GA
Posts: 400
Re: Is it a good deal?

That frame is only worth is weight in scrap...pass.
__________________
"Some of my finest hours have been spent on my back veranda, smoking hemp and observing as far as my eye can see."
- Thomas Jefferson


72 C10 SWB "Work in Progress"
bcutt is offline   Reply With Quote
Old 10-15-2011, 11:06 AM   #12
YBNORML
Registered User
 
YBNORML's Avatar
 
Join Date: May 2010
Location: Edmonton, Alberta
Posts: 3,846
Re: Is it a good deal?

Think about it, someone put a ton of time and money into that frame. And now they are basically giving it away? Why? Probably cause it's junk. I agree with the earlier posts, this kind of work is better handled by yourself or farmed out to someone reputable. Not purchased second hand where you know nothing about what was done!
Run away, I would
Posted via Mobile Device
__________________
---------------------------------------------------------------
Jason.

68’ GMC shortbox
https://67-72chevytrucks.com/vboard/...d.php?t=794201

72' 2WD Blazer
http://67-72chevytrucks.com/vboard/s...d.php?t=425385

67' LongBox C-10
http://67-72chevytrucks.com/vboard/s...d.php?t=691845

InstaGram ybnorml67
YBNORML is offline   Reply With Quote
Old 10-15-2011, 01:16 PM   #13
Flint70step
Registered User
 
Flint70step's Avatar
 
Join Date: Jan 2011
Location: Lake Travis,Texas
Posts: 586
Re: Is it a good deal?

Quote:
Originally Posted by YBNORML View Post
Think about it, someone put a ton of time and money into that frame. And now they are basically giving it away? Why? Probably cause it's junk. I agree with the earlier posts, this kind of work is better handled by yourself or farmed out to someone reputable. Not purchased second hand where you know nothing about what was done!
Run away, I would
Posted via Mobile Device
What he said......if it was a good frame the PO would still be using it and not dumping it for $200.Keep searching or DIY.Be good
__________________
72 Cheyenne Super LWB 350/350 Factory A/C Tilt/Posi White/Med Red/White(on the way)

72 Custom Deluxe Burb(Arizona truck)Nice interior
Great patina

Project Patina Azul http://67-72chevytrucks.com/vboard/s...d.php?t=467668
Flint70step is offline   Reply With Quote
Old 10-15-2011, 03:46 PM   #14
weircc
Registered User
 
weircc's Avatar
 
Join Date: Dec 2008
Location: richmond, MO
Posts: 794
Re: Is it a good deal?

these guys said it best!! too much time in that not to be using my friend!!
__________________
1971 rs camaro under the knife ls3 6 speed swap
1970 396 big block shorty fleet 67 clone
2010 rs/ss camaro
weircc is offline   Reply With Quote
Old 10-15-2011, 03:56 PM   #15
VA72C10
VA72C10
 
VA72C10's Avatar
 
Join Date: Mar 2008
Location: Midlothian, VA
Posts: 25,269
Re: Is it a good deal?

while I agree with the above comments....check to see if the spindles are drop spindles and in good shape. Plus, the frame looks fully boxed. If it was square i'd buy it for the frame, spindles, and brakes, and notch, (and possibly crossmember after checking out how it works with steering...and cut off/scrap the rest...

(spindles/brakes are worth over 200 if it's drop spindles)
__________________
Looking for a 67-72 swb or blazer project in or around VA.
VA72C10 is offline   Reply With Quote
Old 10-15-2011, 04:01 PM   #16
shawno72
C/10 junkie
 
shawno72's Avatar
 
Join Date: Nov 2010
Location: Stockton Ca
Posts: 9,093
Re: Is it a good deal?

Looks like hammer marks on this side of the step notch.
__________________
Shawn

70 LWB C10 current driver/project
http://67-72chevytrucks.com/vboard/s...d.php?t=663051
68 SWB C10 Work in progress.....SOLD
http://67-72chevytrucks.com/vboard/s...d.php?t=559520
72 LWB C10 Sold
71 LWB C10 Sold
68 LWB C10 CST Sold


http://youtu.be/kbB0QrBIs9k

My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"
shawno72 is offline   Reply With Quote
Old 10-15-2011, 04:25 PM   #17
big_al_71
Registered User
 
big_al_71's Avatar
 
Join Date: Jun 2008
Location: South Florida
Posts: 11,375
Re: Is it a good deal?

Pass!!!!
__________________
Get your facts first, and then you can distort them as much as you please!!!!!.



Sylvester's build thread >>>http://67-72chevytrucks.com/vboard/s...ht=big+rebuild
big_al_71 is offline   Reply With Quote
Old 10-15-2011, 08:33 PM   #18
hbaublit
Registered User
 
hbaublit's Avatar
 
Join Date: Feb 2009
Location: Broussard LA
Posts: 28
Re: Is it a good deal?

This is exactly why I posted on here first. I knew it's the place to get honest answers. Thanks everybody.
__________________

1970 Chevy Step
hbaublit is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:43 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com