The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 02-13-2018, 11:13 PM   #1
jaywashburn
Registered User
 
Join Date: Aug 2012
Location: boulder, CO
Posts: 47
Engine priming issue

Hello,fellow members,

seeking some insight on possible reasons I am having an "issue" while priming oiling system on my 350. Motor has been completely gone through by a professional local builder. It was then properly stored indoors for 2 years.
I am just now getting ready to break in cam on it.
I purchased a priming tool & spent about 4-5 minutes spinning the oil pump gear. I have good flow of oil coming from all pushrods on drivers side & but nothing from the passenger side. Also, I did crank the motor over briefly a couple of times during the process but again no flow of oil from pass side.
I have good oil pressure during priming (55 psi).
Could this just a case of not having the right priming tool ? I bought it on Ebay
(sleeved billet shaft). It supposed allow for oil to travel to heads.
Thanks
Attached Images
 
jaywashburn is offline   Reply With Quote
Old 02-13-2018, 11:47 PM   #2
clay68c10
Senior Member
 
clay68c10's Avatar
 
Join Date: Aug 2004
Location: Centennial, CO
Posts: 1,881
Re: Engine priming issue

That tool looks like it should let oil go across to the other side. Maybe the sleeve area isn't quite sealing?

Toss it back in there and spin it for another 5-10 minutes. Sometimes it just takes forever to get the air out of those oil galleries and the lifters. You won't do any harm.
__________________
68 C10 Bought in 89, wrecked in 03. Slow low $ rebuild started '17.
68 Cadillac Sedan de Ville
93 K1500 Short Step, 350, NV4500, EBL flash ECU. Vortec heads & roller cam someday...
02 E320
13 Tahoe LTZ
clay68c10 is offline   Reply With Quote
Old 02-14-2018, 12:21 AM   #3
Steeveedee
Senior Member
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 2,315
Re: Engine priming issue

If you spin the pump enough, you are going to flush all the break-in lube off the cam/lifter wearing surfaces. If it has a roller cam, that's a moot point, though. If you really want oil on all cam surfaces, you need to do the oil pump spinning on half-crankshaft turn intervals, since the lifters are at varying levels in their bores. Once I build an engine, I run the priming tool until I see oil anywhere in the valve train, then fire it up. You are over-doing it, I think.
__________________
'70 Chevy 3/4T Longhorn CST 400/400/3.54 Custom Camper

"Orange Acres"
Steeveedee is offline   Reply With Quote
Old 02-14-2018, 10:46 AM   #4
jaywashburn
Registered User
 
Join Date: Aug 2012
Location: boulder, CO
Posts: 47
Re: Engine priming issue

Thanks guys. It sounds like my concern is much ado about nothing.
jaywashburn is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:11 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com