need input on this - The 1947 - Present Chevrolet & GMC Truck Message Board Network

chincha805 · 01-09-2016, 10:36 AM

ok, i have a 86 4.3L V6 , that is carbureted. my plan is to change the stock intake with a Edelbrock 2111 intake , change the 4 barrel stock carberator with a Edelbrock 1404 (500cfm) caburetor, i am removing all the electronics computers and will need tto change the distributor to non computerized MSD . has anyone done this, my goal is to make this V6 run with out any computers.

Highsider · 01-09-2016, 10:55 AM

I like your thinking.

**joedoh** · 01-09-2016, 03:42 PM

there were a few carbureted 4.3 V6 cars and trucks, try the 84-85 fullsize and same year gbody (monte carlo, malibu, el camino). personally I would buy a new distributor than a 30 year old one, so rockauto or o'reillys should have the parts you need.

and if you have all the harness and computer and the engine runs you are adding a layer of complexity and expense that you dont really need, my advice: install it, get it running, then do your carb and distributor swap. just my opinion though, and my opinion is only worth what it cost.

chincha805 · 01-09-2016, 08:27 PM

i guess what i need to know is what kind of distributor would i need to get? my Oriellys and Napa store are clueless on what to do. will a HEI distributor work. i sure it can be done , i know the expense is greater but thats what i want to do.

**joedoh** · 01-09-2016, 09:47 PM

I just did a quick google search for an HEI distributor for a 4.3 V6 1985 el camino and this came up.

http://www.aipelectronics.com/index....3-8l-4-3l.html

Henry50 · 01-09-2016, 10:46 PM

There wasn't a single wire HEI built from the factory for the 4.3,

Here's a little info that might help,
http://blog.wrenchmanrepair.com/2012...ei-conversion/

**joedoh** · 01-09-2016, 11:51 PM

that looks like totally less work than just using the tbi setup that you already have. I'm just being smarmy of course, but looks like good info if thats really what you want to do.

mr48chev · 01-09-2016, 11:59 PM

O'Reilly's does show a vacuum advance distributor for the 4.3 http://www.oreillyauto.com/site/c/de...2780&ppt=C0334

Evidently the 4.3 came with either a vacuum controlled distributor or a a full computer controlled version in 1985. The compatibility list is the same on the one from OReilly's as the one Joedoh showed if you are inclined to go junk yard hunting.

chincha805 · 01-10-2016, 08:21 PM

i'm going to buy a new one. thanks for the info.

01-09-2016, 10:36 AM	#1
chincha805 Registered User Join Date: Mar 2015 Location: Buellton, CA Posts: 123	need input on this ok, i have a 86 4.3L V6 , that is carbureted. my plan is to change the stock intake with a Edelbrock 2111 intake , change the 4 barrel stock carberator with a Edelbrock 1404 (500cfm) caburetor, i am removing all the electronics computers and will need tto change the distributor to non computerized MSD . has anyone done this, my goal is to make this V6 run with out any computers.

01-09-2016, 10:55 AM	#2
Highsider Registered User Join Date: Jun 2012 Location: Southern Iowa Posts: 944	Re: need input on this I like your thinking. __________________ Jimi J from I-Oh-Way '57 Panel 3105 Met this deer... Roof Swap on my Panel Jim's Bread Truck

01-09-2016, 03:42 PM	#3
joedoh Senior Member Join Date: May 2007 Location: Doodah Kansas Posts: 7,747	Re: need input on this there were a few carbureted 4.3 V6 cars and trucks, try the 84-85 fullsize and same year gbody (monte carlo, malibu, el camino). personally I would buy a new distributor than a 30 year old one, so rockauto or o'reillys should have the parts you need. and if you have all the harness and computer and the engine runs you are adding a layer of complexity and expense that you dont really need, my advice: install it, get it running, then do your carb and distributor swap. just my opinion though, and my opinion is only worth what it cost. __________________ the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393

01-09-2016, 08:27 PM	#4
chincha805 Registered User Join Date: Mar 2015 Location: Buellton, CA Posts: 123	Re: need input on this i guess what i need to know is what kind of distributor would i need to get? my Oriellys and Napa store are clueless on what to do. will a HEI distributor work. i sure it can be done , i know the expense is greater but thats what i want to do.

01-09-2016, 09:47 PM	#5
joedoh Senior Member Join Date: May 2007 Location: Doodah Kansas Posts: 7,747	Re: need input on this I just did a quick google search for an HEI distributor for a 4.3 V6 1985 el camino and this came up. http://www.aipelectronics.com/index....3-8l-4-3l.html __________________ the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393

01-09-2016, 10:46 PM	#6
Henry50 Registered User Join Date: Sep 2011 Location: Evansville In Posts: 173	Re: need input on this There wasn't a single wire HEI built from the factory for the 4.3, Here's a little info that might help, http://blog.wrenchmanrepair.com/2012...ei-conversion/

01-09-2016, 11:51 PM	#7
joedoh Senior Member Join Date: May 2007 Location: Doodah Kansas Posts: 7,747	Re: need input on this that looks like totally less work than just using the tbi setup that you already have. I'm just being smarmy of course, but looks like good info if thats really what you want to do. __________________ the mass of men live lives of quiet desperation if there is a problem, I can have it. new project WAYNE http://67-72chevytrucks.com/vboard/s...d.php?t=844393

01-09-2016, 11:59 PM	#8
mr48chev Registered User Join Date: Jul 2007 Location: Toppenish, WA Posts: 15,304	Re: need input on this O'Reilly's does show a vacuum advance distributor for the 4.3 http://www.oreillyauto.com/site/c/de...2780&ppt=C0334 Evidently the 4.3 came with either a vacuum controlled distributor or a a full computer controlled version in 1985. The compatibility list is the same on the one from OReilly's as the one Joedoh showed if you are inclined to go junk yard hunting. __________________ Founding member of the too many projects, too little time and money club. My ongoing truck projects: 48 Chev 3100 that will run a 292 Six. 71 GMC 2500 that is getting a Cad 500 transplant. 77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.

01-10-2016, 08:21 PM	#9
chincha805 Registered User Join Date: Mar 2015 Location: Buellton, CA Posts: 123	Re: need input on this i'm going to buy a new one. thanks for the info.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.