Shawley's 1969 C10 Project - Page 2 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

shawley · 06-05-2015, 01:38 PM

Got a bunch of work done, not much for pictures,

Alternator mounted up

Transmission cooler mounted up

Rad all installed

Rad fan in there now too

We fired it up the other day too, and it started just fine and ran. Getting very close to driving it!!

Did Por15 gloss black paint on the floors with the rust protection.

More wiring fun, looks like a mess but its just getting all cleaned up and integrated

Then did my Wirez sound deadening on the floors and back wall!

It's getting so close!!!!!!!!!!!

shawley · 06-06-2015, 11:43 AM

A buddy from work came to help out and get the din hole for me new Pioneer deck cut out, I knew if I cut it, the hole would be crooked

We got the Dakota Digital cluster all working, just need to calibrate the speedo, once I get it driving

My Lumens LED headlights are working, and so are my LED side markers and park lights! Means all my wiring was correct haha.

BossHogg69 · 06-06-2015, 01:08 PM

Nice work - what brand are those parking lamps?

shawley · 06-06-2015, 01:11 PM

Thanks! They are all from LMC, I don't remember what brand they were though
Posted via Mobile Device

shawley · 06-09-2015, 10:42 AM

I got he under hood all wired up, 140amp alternator fused to the battery, my Accuair all connected to the battery, the stereo power routed to the cab, and a couple good grounds for the battery and in the engine bay.

My buddy Luke came by and worked on my truck with me till very late Saturday night so we got lots done, cleaned up all the wiring and got my deck installed, along with all the RCA's and speaker lines for the future stereo routed.

Deck installed, heater controls reinstalled, ash tray back in, usb mounted, and then the sub level control where the old manual choke was.

Got the cluster all in, tested and working 100%, and laid down the carpet in the cab.

It ended up fitting damn good, just need to do a little adjusting because this carpet is for a truck with a bit more of a raised floor for a shifter as my truck used to have a floor shifter, but didn't have the raised floor.

All powered up and working, just need my amps/speakers/custom kicks and I'll have sound

Lots more to do but so little left to do!

Really just need my shocks from Bag Barn, a coolant overflow, and mufflers and I'll be ale to take it around the block, then hopefully toss the box back on.

Justin@EntropyRad · 06-09-2015, 11:20 AM

really coming along!

shawley · 06-11-2015, 10:53 PM

Seats in,

Carpet too!

And the steering wheel!!!

And got a rad overflow tank

shawley · 06-18-2015, 03:52 PM

Truck is soooooo close to being finished up!!!! New mirrors on it now too.

Transmission needs one thing adjusted/changed and then the bed will go on and it's ready to drive! Just needs proper exhaust and an alignment.

Engine is pretty well all finished up, and we redid the alternator bracket as the last one was flexing way too much

Interior is all finished up besides the stereo, need to still build custom kick panels and my sub box.

False gas cap on there too.

Built a bracket for the Accuair controller

shawley · 06-23-2015, 10:23 AM

Well I got the truck going and driving!!!! My buddy Ryan came by and got the majority of the tranny issues resolved, as someone has modified it to run no lock up.

Took it around the block, everything is working awesome, the accuair, the motor, all of it!

Can't wait to get the bed on and get it all going

Need to also calibrate my GPS speedo

knomadd · 06-23-2015, 12:53 PM

That looks beautiful! Nice work!

Mr Chevorlet · 06-23-2015, 01:16 PM

Nice build, nice truck thanks for sharing.

**Sac** · 06-24-2015, 01:10 AM

Nice work!

WarMonger · 06-25-2015, 06:17 PM

truck looks amazing. great work

shawley · 06-30-2015, 07:57 PM

Thanks guys!

Got box ready, and cut the hole for the fuel filler

Then thanks everyone for lifting, when I couldn't

and drove it to the garage!

shawley · 07-21-2015, 01:04 PM

The truck is getting so close to completion, had some transmission issues that we thought could be a simple fix, but turned out that the transmission itself was toast.

Had 1st and 2nd gear but no 3rd or 4th so got it towed to a local transmission shop, the tow truck driver himself owns a 72 Suburban

Once I got there the owner had a 66' C10 himself, and knew lots about these trucks and also lots about the 700R4 transmissions, so it was great to get it worked on there

Turned out it needed to be fully rebuilt, so that's what I had them do, and now I'm able to drive it!

Just needs some exhaust work, the bed cut out for the diff, the stereo completed and and then it's finished!!! Well at least for this season.

Not bad for 8 months

**RRR18** · 07-21-2015, 02:34 PM

Great work. You should be proud.

92GMCDriver · 07-22-2015, 12:01 AM

Love this truck, nice to see another Albertan member on here!

shawley · 08-31-2015, 01:13 PM

Thanks guys!

Might as well at some more current pics, still haven't been able to do my stereo yet, just no time.

At Drift For The Kids at Castrol Raceway

Took it to Rock'n August Drive In Movie, wanted to recline the seats to just lifted the front and dumped the back!

Rock'n August Car Show

At the shop one day

knomadd · 08-31-2015, 02:40 PM

That looks really good! I love those wheels.

88Stanger · 08-31-2015, 03:26 PM

very nice job!

knomadd · 09-02-2015, 04:30 PM

What are the specs on your wheels?

mcbassin · 09-03-2015, 08:28 AM

Awesome work on this truck. You really took it a long way in a short period of time. Looks great too!

06-05-2015, 01:38 PM	#26
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Got a bunch of work done, not much for pictures, Alternator mounted up Transmission cooler mounted up Rad all installed Rad fan in there now too We fired it up the other day too, and it started just fine and ran. Getting very close to driving it!! Did Por15 gloss black paint on the floors with the rust protection. More wiring fun, looks like a mess but its just getting all cleaned up and integrated Then did my Wirez sound deadening on the floors and back wall! It's getting so close!!!!!!!!!!!

06-06-2015, 11:43 AM	#27
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project A buddy from work came to help out and get the din hole for me new Pioneer deck cut out, I knew if I cut it, the hole would be crooked We got the Dakota Digital cluster all working, just need to calibrate the speedo, once I get it driving My Lumens LED headlights are working, and so are my LED side markers and park lights! Means all my wiring was correct haha.

06-06-2015, 01:08 PM	#28
BossHogg69 motor exploder Join Date: Mar 2009 Location: Pittsburgh, PA Posts: 2,346	Re: Shawley's 1969 C10 Project Nice work - what brand are those parking lamps? __________________ Adam 1969 Chevy CST/10 stepside, DART Big M/TREMEC Magnum Extreme/3.73's w/Detroit Truetrac 1965 Chevy Bel Air Wagon (daily driver), 327/TH350,10 bolt w/3.08's 1961 Chevy Bel Air Sport Coupe, ZZ454/M21/9" rear w/3.50's & Detroit Truetrac 2005 GMC 1500 ccsb 2wd, 6.0L/4L65e/3.73 G80 2006 GMC 2500HD ccsb 4x4, DMax LBZ/Allison 6spd/4.56's w/Detroit TrueTrac Use the SEARCH function on this forum - it is your friend!!

06-06-2015, 01:11 PM	#29
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Thanks! They are all from LMC, I don't remember what brand they were though Posted via Mobile Device

06-09-2015, 10:42 AM	#30
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project I got he under hood all wired up, 140amp alternator fused to the battery, my Accuair all connected to the battery, the stereo power routed to the cab, and a couple good grounds for the battery and in the engine bay. My buddy Luke came by and worked on my truck with me till very late Saturday night so we got lots done, cleaned up all the wiring and got my deck installed, along with all the RCA's and speaker lines for the future stereo routed. Deck installed, heater controls reinstalled, ash tray back in, usb mounted, and then the sub level control where the old manual choke was. Got the cluster all in, tested and working 100%, and laid down the carpet in the cab. It ended up fitting damn good, just need to do a little adjusting because this carpet is for a truck with a bit more of a raised floor for a shifter as my truck used to have a floor shifter, but didn't have the raised floor. All powered up and working, just need my amps/speakers/custom kicks and I'll have sound Lots more to do but so little left to do! Really just need my shocks from Bag Barn, a coolant overflow, and mufflers and I'll be ale to take it around the block, then hopefully toss the box back on.

06-09-2015, 11:20 AM	#31
Justin@EntropyRad Registered User Join Date: Jan 2015 Location: Charlotte, NC Posts: 483	Re: Shawley's 1969 C10 Project really coming along! __________________ * Call me NOT the website number* Justin Novick (773) 303-8251 Sales/Support Entropy Radiator / Engineered Cooling Products "The Sexiest Radiators For The Sexiest Hot Rods" - www.EntropyRad.com www.speedcooling.com

06-11-2015, 10:53 PM	#32
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Seats in, Carpet too! And the steering wheel!!! And got a rad overflow tank

06-18-2015, 03:52 PM	#33
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Truck is soooooo close to being finished up!!!! New mirrors on it now too. Transmission needs one thing adjusted/changed and then the bed will go on and it's ready to drive! Just needs proper exhaust and an alignment. Engine is pretty well all finished up, and we redid the alternator bracket as the last one was flexing way too much Interior is all finished up besides the stereo, need to still build custom kick panels and my sub box. False gas cap on there too. Built a bracket for the Accuair controller

06-23-2015, 10:23 AM	#34
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Well I got the truck going and driving!!!! My buddy Ryan came by and got the majority of the tranny issues resolved, as someone has modified it to run no lock up. Took it around the block, everything is working awesome, the accuair, the motor, all of it! Can't wait to get the bed on and get it all going Need to also calibrate my GPS speedo

06-23-2015, 12:53 PM	#35
knomadd Registered User Join Date: Jul 2012 Location: Rosenberg, Texas Posts: 3,506	Re: Shawley's 1969 C10 Project That looks beautiful! Nice work! __________________ -Duane C/10 Club Texas member 1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project) 1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)

06-23-2015, 01:16 PM	#36
Mr Chevorlet Rusty Nuts Join Date: Sep 2008 Location: Clever Missouri Posts: 1,338	Re: Shawley's 1969 C10 Project Nice build, nice truck thanks for sharing. __________________ (Clever Missouri) Southwest Larry Mr Chevrolet My Build, The Marathon Truck http://67-72chevytrucks.com/vboard/s...d.php?t=604414

06-24-2015, 01:10 AM	#37
Sac Senior Member Join Date: Nov 2013 Location: Franklinton, LA Posts: 256	Re: Shawley's 1969 C10 Project Nice work! __________________ Green Survivor Father/Son Truck <SeveredTies>

06-25-2015, 06:17 PM	#38
WarMonger Registered User Join Date: Jan 2015 Location: Ventura, CA Posts: 818	Re: Shawley's 1969 C10 Project truck looks amazing. great work __________________ ..................... ____ .........________//__{\_____ ,,,,,,,/__(O)___//___/__(O)_/ 1970 C20 -_--_--_- ______ _--_--_- /___\|__\____ -_--_-_ \|_(0)\|__\|_(0)] 1972 K5

06-30-2015, 07:57 PM	#39
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Thanks guys! Got box ready, and cut the hole for the fuel filler Then thanks everyone for lifting, when I couldn't and drove it to the garage!

07-21-2015, 01:04 PM	#40
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project The truck is getting so close to completion, had some transmission issues that we thought could be a simple fix, but turned out that the transmission itself was toast. Had 1st and 2nd gear but no 3rd or 4th so got it towed to a local transmission shop, the tow truck driver himself owns a 72 Suburban Once I got there the owner had a 66' C10 himself, and knew lots about these trucks and also lots about the 700R4 transmissions, so it was great to get it worked on there Turned out it needed to be fully rebuilt, so that's what I had them do, and now I'm able to drive it! Just needs some exhaust work, the bed cut out for the diff, the stereo completed and and then it's finished!!! Well at least for this season. Not bad for 8 months



Register or Log In To remove these advertisements.

07-21-2015, 02:34 PM	#41
RRR18 Senior Member Join Date: Nov 2010 Location: Lordstown, OH / Wentzville, MO Posts: 870	Re: Shawley's 1969 C10 Project Great work. You should be proud. __________________ '67 BAD IDEA Follow on Instagram https://www.instagram.com/rtimes3c10/ Ryan

07-22-2015, 12:01 AM	#42
92GMCDriver Registered User Join Date: Oct 2010 Location: Lethbridge, Alberta Posts: 124	Re: Shawley's 1969 C10 Project Love this truck, nice to see another Albertan member on here! __________________ Cole. 1967 GMC c15 1991 k2500 2005 2500hd Duramax

08-31-2015, 01:13 PM	#43
shawley Registered User Join Date: Oct 2014 Location: Edmonton, AB Posts: 48	Re: Shawley's 1969 C10 Project Thanks guys! Might as well at some more current pics, still haven't been able to do my stereo yet, just no time. At Drift For The Kids at Castrol Raceway Took it to Rock'n August Drive In Movie, wanted to recline the seats to just lifted the front and dumped the back! Rock'n August Car Show At the shop one day __________________ My 69' C10 build thread

08-31-2015, 02:40 PM	#44
knomadd Registered User Join Date: Jul 2012 Location: Rosenberg, Texas Posts: 3,506	Re: Shawley's 1969 C10 Project That looks really good! I love those wheels. __________________ -Duane C/10 Club Texas member 1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project) 1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)

08-31-2015, 03:26 PM	#45
88Stanger Registered User Join Date: Mar 2015 Location: Washington State Posts: 1,644	Re: Shawley's 1969 C10 Project very nice job!

09-02-2015, 04:30 PM	#46
knomadd Registered User Join Date: Jul 2012 Location: Rosenberg, Texas Posts: 3,506	Re: Shawley's 1969 C10 Project What are the specs on your wheels? __________________ -Duane C/10 Club Texas member 1971 Chevy C10 "Brutus" SWB Fleetside 2016 6.0L (L96) 6L90E (driver/project) 1965 Pontiac GTO "Royal Goat" 400/TH400 w/AC (my baby)

09-03-2015, 08:28 AM	#47
mcbassin Still Learning Join Date: Jul 2009 Location: Central Oklahoma Posts: 10,108	Re: Shawley's 1969 C10 Project Awesome work on this truck. You really took it a long way in a short period of time. Looks great too! __________________ Mike "69 Short Wide" My Project 86 Silverado Landen's Project Instagram: @mcbassin My Website C/10 Club Oklahoma Facebook Group

Register or Log In To remove these advertisements.