|
09-29-2018, 08:50 PM
|
#1 |
|
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,312
|
well im an idiot....
LS Oil pan swap.
Was having problems with my torque wrench for some reason ......... think it was the angle. I overtightened the oil pickup tube 10mm bolt and snapped if off ..... so mad at myself as usually Im really careful with that stuff in aluminium What are my options here ? ........ 
__________________
FAKKY 57 PANEL BUILD |
|
|
|
09-30-2018, 01:15 PM
|
#2 |
|
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,312
|
Re: well im an idiot....
Git out .....
__________________
FAKKY 57 PANEL BUILD |
|
|
|
|
10-01-2018, 08:12 PM
|
#3 |
|
Moderator
 
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,153
|
Re: well im an idiot....
Not sure but that snapped bolt does not look correct...with that turned down end it most likely bottomed out in the bolt hole before clamping down fully....
Check the bore threads in the block for damage Double check the depth of the thread needed and make sure bolt is not too long I always dry assemble first then back the bolts out and apply thread locker to each bolt Tighten to 106 in pounds.... Thats inch pounds Lucky you got the broken piece out ok... Good luck 
__________________
Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox 
Last edited by AussieinNC; 10-01-2018 at 08:18 PM. |
|
|
|
|
10-01-2018, 08:55 PM
|
#4 |
|
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,312
|
Re: well im an idiot....
Not sure. But it could have bottomed out by over tightetning.
Have another one in the head (not my fault this one) on exhuast manifold. What do you think - use a weld/nut or try the same appraoch with left hand drill bit. See the "Eagles V Collingwood"  yes Sir.
__________________
FAKKY 57 PANEL BUILD |
|
|
|
|
10-02-2018, 08:46 PM
|
#5 |
|
Moderator
Join Date: Jun 2017
Location: Cherryville, NC
Posts: 2,153
|
Re: well im an idiot....
If the bolt in the exhaust manifold is in the head it should be center drilled and a stud extractor used to remove the broken stud....
While you are at it, replace all the studs / bolts with new ones and make sure you use anti sieze on the threads when re-installing them... Eagles v Collingwood...nah...I am Sydney born...more likely yo be Eels v Rabitohs.... Where you at mate?
__________________
Family and country before all others... 2006 Chevy Silverado (Daily Driver) 2012 Chevy Equinox
|
|
|
|
|
10-02-2018, 09:10 PM
|
#6 | ||||
|
"I ain't nobody, dork."
Join Date: Sep 2007
Location: Whidbey Island, Washington
Posts: 8,921
|
Re: well im an idiot....
Here is a thread where I removed the broken exhaust manifold bolt on the LS in my '06 Silverado K2500 HD. Hope it helps.
http://www.67-72chevytrucks.com/vboa...d.php?t=587659 Gary
__________________
'cuz chicks dig scars... My 1972 GMC 1500 Super Custom (Creeping Death) "long term" build thread. The Rebuild of Creeping Death after the wreck Quote:
Quote:
Quote:
Quote:
|
||||
|
|
|
|
10-05-2018, 04:39 PM
|
#7 | |
|
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,312
|
Re: well im an idiot....
Quote:
St Petersburg - FL ...... originally from Perth. 
__________________
FAKKY 57 PANEL BUILD |
|
|
|
|
|
10-05-2018, 04:40 PM
|
#8 | |
|
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,312
|
Re: well im an idiot....
Quote:
__________________
FAKKY 57 PANEL BUILD |
|
|
|
|
|
10-06-2018, 12:53 PM
|
#9 |
|
Registered User
Join Date: Sep 2016
Location: Redington Beach
Posts: 1,312
|
Re: well im an idiot....
Curious minds gary.
Tried the easy out/left hand drill bit - no beuno on this one either. So going to try weld. Why does the weld not stick to the aluminium block though - I know its mig/steel wire not aluminium wire ....... but still thought it would try and stick and potentially the damage the threads etc.
__________________
FAKKY 57 PANEL BUILD |
|
|
|
|
10-09-2018, 10:18 PM
|
#10 |
|
Registered User
Join Date: Oct 2018
Location: Bradford maine
Posts: 7
|
Re: well im an idiot....
I have luck by plug welding a flatwasher to the broken bolt n then tackweld a nut on in place and then plug welding that mainly cause you can see the broken bolt and get a good well to it with washer then can weld nut solid to washer easier than to small bolt...I've just found this to work for me as working on big trucks every day I run into broken bolts often
|
|
|
|
 |
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
