The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 11-30-2017, 11:53 AM   #1
1SG.Rob
Registered User
 
1SG.Rob's Avatar
 
Join Date: May 2017
Location: Vancouver, WA
Posts: 87
Replacing brake light switch

Good morning, gents! This weekend I will be replacing the brake light switch in my '69 C10. This is the first time doing this and I am little more than a novice when it comes to electronics and wiring. Is there anything specific I should watch out for? Any tips or advice? This is my daily driver for work so I gotta get these lights fixed ASAP. Thanks!!
1SG.Rob is offline   Reply With Quote
Old 11-30-2017, 12:25 PM   #2
randy500
Account Suspended
 
Join Date: Jul 2016
Location: Tacoma, WA
Posts: 6,873
Re: Replacing brake light switch

It’s a very difficult job because there is no room to work, the switch is above the steering column in a cavity of the brake pedal bracket. If you get frustrated just pull the steering column to get some working room.
Remove the switch first then the wiring from the switch.
Remove the lower nut on the switch, hopefully you can hold the lower nut with one hand and twist the upper part of the switch to remove the nut since there is not room for tools. Sometimes the nut is too tight to do it that way though.

The wire has a Clip on either side, I would make a wood wedge for each clip to disengage them both before pulling the connector off, releasing both clips at the same time can be difficult.
randy500 is offline   Reply With Quote
Old 11-30-2017, 12:45 PM   #3
1SG.Rob
Registered User
 
1SG.Rob's Avatar
 
Join Date: May 2017
Location: Vancouver, WA
Posts: 87
Re: Replacing brake light switch

Quote:
Originally Posted by randy500 View Post
It’s a very difficult job because there is no room to work, the switch is above the steering column in a cavity of the brake pedal bracket. If you get frustrated just pull the steering column to get some working room.
Remove the switch first then the wiring from the switch.
Remove the lower nut on the switch, hopefully you can hold the lower nut with one hand and twist the upper part of the switch to remove the nut since there is not room for tools. Sometimes the nut is too tight to do it that way though.

The wire has a Clip on either side, I would make a wood wedge for each clip to disengage them both before pulling the connector off, releasing both clips at the same time can be difficult.
Ouch, not the quick job I was hoping for. I've been meaning to replace the main dash wiring harness, might be best to just do them both at the same time and make a weekend of it. Thanks for the info!
1SG.Rob is offline   Reply With Quote
Old 11-30-2017, 12:59 PM   #4
demian5
Registered User
 
demian5's Avatar
 
Join Date: Aug 2016
Location: Lake Forest, CA
Posts: 2,177
Re: Replacing brake light switch

If you have some long needle nose pliers, and some long 90 degree ones, that helps a lot. Get it adjusted right the first time.
__________________
"Work hard, use your vacation days."
1970 C15 GMC Long Bed
1986 C20 Scottsdale
1983 K2500 Sierra Classic Suburban 6.2
Instagram: C10sofOC
demian5 is offline   Reply With Quote
Old 11-30-2017, 01:03 PM   #5
Andy4639
Old member
 
Andy4639's Avatar
 
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
Talking Re: Replacing brake light switch

I cut a piece of 2x2 off to fit between the brake pedal and the underside of the steering column to hold the brake pedal down. This takes the pressure off of the switch. The loosen the nut holding the switch. Pop the wire connector off the switch and screw it out. Nothing to it other than laying on your back under the dash.
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver
Seeing the USA in a 71


Upstate SC GM Truck Club
2013,14 and 2016 Hot Rod Pour Tour


http://upstategmtrucks.com/



Get out and drive the truck this summer and have some fun!
It sucks not being able to hear!

LWB trucks rule, if you don't think so measure your SWB!
After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.
Andy4639 is offline   Reply With Quote
Old 11-30-2017, 01:58 PM   #6
demian5
Registered User
 
demian5's Avatar
 
Join Date: Aug 2016
Location: Lake Forest, CA
Posts: 2,177
Re: Replacing brake light switch

Quote:
Originally Posted by Andy4639 View Post
Nothing to it other than laying on your back under the dash.
Way easier when you have an auto trans truck to lay across the floor.
__________________
"Work hard, use your vacation days."
1970 C15 GMC Long Bed
1986 C20 Scottsdale
1983 K2500 Sierra Classic Suburban 6.2
Instagram: C10sofOC
demian5 is offline   Reply With Quote
Old 11-30-2017, 04:13 PM   #7
1SG.Rob
Registered User
 
1SG.Rob's Avatar
 
Join Date: May 2017
Location: Vancouver, WA
Posts: 87
Re: Replacing brake light switch

Thanks for the advice, gents. It really helps me make my plan of attack.
1SG.Rob is offline   Reply With Quote
Old 11-30-2017, 05:20 PM   #8
Andy4639
Old member
 
Andy4639's Avatar
 
Join Date: Jan 2002
Location: Liberty, & Garden City S.C. , U.S.
Posts: 19,936
Talking Re: Replacing brake light switch

Quote:
Originally Posted by demian5 View Post
Way easier when you have an auto trans truck to lay across the floor.
At 57 years old nothing about laying in the floor board is easy!
__________________
1971 LWB Custom, 6.0LS & 4L80E, Speedhut.com GPS speedometer & gauges with A/C. 20" Boss 338's Grey wheels 4 wheel disc brakes. My Driver
Seeing the USA in a 71


Upstate SC GM Truck Club
2013,14 and 2016 Hot Rod Pour Tour


http://upstategmtrucks.com/



Get out and drive the truck this summer and have some fun!
It sucks not being able to hear!

LWB trucks rule, if you don't think so measure your SWB!
After talking to tech support at Air Lift I have found out that the kit I need is 60811. Per the measurements I gave them. Ride height of truck inside spring and inside diameter of springs.
Andy4639 is offline   Reply With Quote
Old 11-30-2017, 11:37 PM   #9
68c10airstream
Registered User
 
68c10airstream's Avatar
 
Join Date: Mar 2013
Location: Marquette michigan
Posts: 828
Re: Replacing brake light switch

I'll throw this train of thought into the mix. If you possibly are going to an overdrive trans and/or cruise control in the future consider having the brake switch turn on/off a relay. Relays have an energized set of contacts and a de=energized set of contacts. The relay can then take the amps load of the circuit, remotely mounted (your choice of location) save wear and tear on the brake switch and now the brake switch is doing a double duty.

As an example; brake pedal pushed= 12volts + going to brake lights, Brake pedal released= the same 12volts+ that was going to the brake lights is now diverted to the lockup torque converter solenoid. If using cruise, you could tap into the correct side of the relay output as needed.

You can do this for less than 20 dollars.
68c10airstream is offline   Reply With Quote
Old 12-01-2017, 09:04 AM   #10
yuccales
Registered User
 
yuccales's Avatar
 
Join Date: May 2011
Location: Northern Calif.
Posts: 3,560
Re: Replacing brake light switch

All great info. Remember to block your wheels and/or use your e-brake! All your twisting around, squirming, etc, under that dash, you don't want to pull that thing out of park, or knock it out of gear! Don't ask how I know.
yuccales is offline   Reply With Quote
Old 12-04-2017, 01:57 PM   #11
1SG.Rob
Registered User
 
1SG.Rob's Avatar
 
Join Date: May 2017
Location: Vancouver, WA
Posts: 87
Re: Replacing brake light switch

Thanks for the information everyone. I was able to get it switched out on Saturday with relatively little trouble. Brake lights are back to fully operational!
1SG.Rob is offline   Reply With Quote
Old 03-29-2018, 07:44 PM   #12
cgster
Registered User
 
Join Date: Aug 2015
Location: Texas
Posts: 324
Re: Replacing brake light switch

Quote:
Originally Posted by 1SG.Rob View Post
Thanks for the information everyone. I was able to get it switched out on Saturday with relatively little trouble. Brake lights are back to fully operational!
Is there any adjustments you have to make when replacing the brake light switch?
cgster is offline   Reply With Quote
Old 03-30-2018, 12:37 PM   #13
1SG.Rob
Registered User
 
1SG.Rob's Avatar
 
Join Date: May 2017
Location: Vancouver, WA
Posts: 87
Re: Replacing brake light switch

Quote:
Originally Posted by cgster View Post
Is there any adjustments you have to make when replacing the brake light switch?
Yeah, you do have to adjust the screw on the switch a little bit to account for brake pedal travel. When I first installed the new switch, the lights were on no matter where the break pedal was. So you have to adjust it a bit so the lights go off when the pedal is not pushed down.
1SG.Rob is offline   Reply With Quote
Old 03-30-2018, 01:24 PM   #14
68 P.O.S.
Registered User
 
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,659
Re: Replacing brake light switch

I'm working on slowly rewiring my 72 and I've been avoiding this part cause I know it's a pain. Last time I did one was 15 years ago.
__________________
72 C10 lwb fleetside -stock 350/350 combo
68 P.O.S. is offline   Reply With Quote
Old 03-30-2018, 10:47 PM   #15
phat69
Registered User
 
Join Date: Mar 2018
Location: Texas
Posts: 51
Re: Replacing brake light switch

I too have tried to adjust mine but I gave because it's not road worthy but I'll fix that this weekend.
phat69 is offline   Reply With Quote
Old 04-24-2018, 11:30 AM   #16
68 P.O.S.
Registered User
 
Join Date: Jan 2007
Location: Puyallup, WA
Posts: 1,659
Re: Replacing brake light switch

I discovered another great way to remove a stuck switch. A hacksaw blade!
__________________
72 C10 lwb fleetside -stock 350/350 combo
68 P.O.S. is offline   Reply With Quote
Old 05-05-2018, 02:43 PM   #17
iriereggaeman
Registered User
 
iriereggaeman's Avatar
 
Join Date: Oct 2016
Location: Lake Mary, FL
Posts: 139
Re: Replacing brake light switch

Thanks for the good tips here. I always look at the forum before attempting a fix I haven't done before. The discussion helped me quickly locate the switch, make a depth adjustment, and get my brake lights working again! All, in about 15 minutes.
iriereggaeman is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:21 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com