proper placement - The 1947 - Present Chevrolet & GMC Truck Message Board Network

GMC JUNKIE TOO · 02-09-2003, 11:40 PM

I have question about a couple things. I have a sbc in the I6 position I installed a set of headers that a few other pepole said the collectors were paralell with the frame on theirs. I was wondering if the engines angle is difrent in the v8 position as opposed to the I6 position I know it will be about 3 farther forwards.

crazy longhorn · 02-10-2003, 12:20 AM

there isnt a noticeable diffference in the height/angle in I6 vs v8 position......that i could find anyway. I have hooker comps on mine , & the collectors are parallel with ea other, & show approx 2 1/4" below the frame. I dont have any shots of the bottom of the frame, but a couple eng shots. here is the link .... http://community.webshots.com/user/hotrodhorn I would say the Hookers are pretty much parallel with the frame. What headers are you running? crazyL

Longhorn Man · 02-10-2003, 12:41 AM

Here is a belly shot of mine with Super Comps with the engine in the proper location. (small block)

crazy longhorn · 02-10-2003, 12:50 AM

thats pretty much how my Comps hang in I 6 position....just a little farther to the rear....crazyL

GMC JUNKIE TOO · 02-10-2003, 12:53 AM

Thank guys I will leave it where it is.

02-09-2003, 11:40 PM	#1
GMC JUNKIE TOO THE QUICKER FIXERUPER Join Date: Jul 2002 Location: Ok Posts: 615	proper placement I have question about a couple things. I have a sbc in the I6 position I installed a set of headers that a few other pepole said the collectors were paralell with the frame on theirs. I was wondering if the engines angle is difrent in the v8 position as opposed to the I6 position I know it will be about 3 farther forwards.

02-10-2003, 12:20 AM	#2
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	there isnt a noticeable diffference in the height/angle in I6 vs v8 position......that i could find anyway. I have hooker comps on mine , & the collectors are parallel with ea other, & show approx 2 1/4" below the frame. I dont have any shots of the bottom of the frame, but a couple eng shots. here is the link .... http://community.webshots.com/user/hotrodhorn I would say the Hookers are pretty much parallel with the frame. What headers are you running? crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

02-10-2003, 12:50 AM	#4
crazy longhorn Fabricate till you "puke" Join Date: Jun 2002 Location: Ill Posts: 9,403	thats pretty much how my Comps hang in I 6 position....just a little farther to the rear....crazyL __________________ 69 longhorn,4" chop,3/5 drop, 1/2 ton suspension/disc brakes,1 1/2" body drop,steel tilt clip, 5.3/Edelbrock rpm intake/600 carb, Hooker streetrod shorties,2 1/2" exhaust/ H pipe/50's Flows , 6 spd Richmond trans,12 bolt/ 3.40 gears....

02-10-2003, 12:41 AM	#3
Longhorn Man its all about the +6 inches Join Date: Jan 2001 Location: Hilliard Ohio Posts: 2,693	Here is a belly shot of mine with Super Comps with the engine in the proper location. (small block)

02-10-2003, 12:53 AM	#5
GMC JUNKIE TOO THE QUICKER FIXERUPER Join Date: Jul 2002 Location: Ok Posts: 615	Thank guys I will leave it where it is.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.