The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-07-2018, 11:45 AM   #1
Keystone_Hate
Registered User
 
Join Date: Apr 2017
Location: Colorado Springs
Posts: 123
Edelbrock jetting for altitude

72 C10, stock 350 crate engine, edelbrock 1405, HEI.

Currently at 6000ft in Colorado Springs.

I figured out how I want to re-jet going by the plug reading and the Edelbrock adjustment chart. So my question isn't as to what jets/rods I should use.

The question is this, I am driving from Colorado Springs to New Braunfels Texas the end of this month for a road trip, a difference of about 5500ft in elevation. If I re-jet my carb now for current elevation of 6000ft, am I going to hurt the engine by doing a road trip to a lower elevation for a few days? I know it will be running a little lean for majority of the trip but do you guys think this is OK?

It says in the edelbrock manual to not worry about adjusting for altitude if you're only gonna be there for a little while. That's in reference to going UP in altitude where you'd be running rich for a bit instead of going down where you'd be running lean.

I'm not racing or anything crazy, just a long easy cruise to texas.

Would you guys mess with it now, or just leave it alone and worry about it upon returning to elevation after this road trip? I'd hate to develop a ping or extreme lean condition half way through my trip and have to mess with jetting on the road.

My only idea as to this being okay is that a 1406 comes with factory leaner jetting for better mileage, which is what I am going to match with my re-tune of my 1405. The 1406s are setup from the factory at the same elevation as the 1405, so i think I will be alright. Just looking for some opinions.
Keystone_Hate is offline   Reply With Quote
Old 03-07-2018, 03:39 PM   #2
truckster
Senior Member
 
truckster's Avatar
 
Join Date: Jan 2001
Location: Orem, Utah
Posts: 4,326
Re: Edelbrock jetting for altitude

I've never worried about retuning my Quadrajets when I go to sea level.
__________________
If I didn't build it or fix it, it's probably not mine.
truckster is offline   Reply With Quote
Old 03-07-2018, 06:29 PM   #3
Dead Parrot
Registered User
 
Join Date: Aug 2012
Location: Oklahoma City, OK
Posts: 1,089
Re: Edelbrock jetting for altitude

Go ahead and tune your carb for your current location. Research how much richer you will need for where you are going. Edelbrock has a nice tuning chart in the carb manuals. Find a set of rods and springs that will get you close with whatever jets you wind up with. Don't worry about changing jets. One nice thing about the 140x carbs is a rod/spring change is a 5 minute road side task. You may never need to change anything during your trip but at least you will be ready if you notice some pinging or knocking.

I did the reverse when I went from OKC to central CO to visit some friends at 9000ft. Just made a rod/spring change during a gas/rest stop somewhere around 6000ft. Really made a difference compared to the prior trip where I didn't make a change.
Dead Parrot is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 05:26 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com