Register or Log In To remove these advertisements. |
|
|
|
Thread Tools | Display Modes |
12-19-2004, 02:32 PM | #1 |
Dave's not here, man
Join Date: Jun 2004
Location: Winder, Georgia
Posts: 2,000
|
Need a carburetor...what kind??
I have a 68 SWB with a 307/Powerglide tranny. My Rochester carb started to leak around the front of the float bowl and around the baseplate gasket. I rebuilt it with no success because it still leaks. I've been looking for a replacement but I'm new to the carb. world and I don't know what I should use. Like most people, I'm on a budget and the truck is a daily driver so horsepower gains and performance aren't an issue. The other problem I'm trying to tackle is that the baseplate studs that stick up from the manifold are in bad shape and will need replacing. Will I need to get another manifold or can you just by the studs. Sorry for the long post but I'm really don't know what my next step should be...
Thanks in advance!! |
12-19-2004, 02:51 PM | #2 |
Garage Queen Material
Join Date: Oct 2002
Location: USA
Posts: 4,129
|
i'll sell you an edelbrock avs thunder series carb, 650cfm, plus.... the dual feed fuel line for $300
|
12-19-2004, 03:08 PM | #3 |
Registered User
Join Date: Sep 2004
Posts: 96
|
I tell ya...and plenty people disagree with me....but The Q-jet is the best carb for your chevy IF and only IF you plan on driving it daily.
Holley makes great carbs, but for stock performance I would stick with the Q-jet personal opinion....for what its worth |
12-20-2004, 12:56 AM | #4 |
Registered User
Join Date: Nov 2004
Location: "Under Montana skies."
Posts: 1,836
|
I, too, would stick with your carb and replace the gaskets that leak. Perhaps have a professional do it who has to guarantee against leaks. If it runs fine otherwise, maybe you would only need to pay for gasket replacement.
The intake studs are prolly available at most any parts store with a hardware-style bolt selection. Double nut one of the studs, pull it, and take it in to match it up.
__________________
'71 GMC K20 Suburban, '71 GMC K10 Suburban, '72 Chevy C10 CST Suburban, '72 Chevy K20 clunker pickup. |
12-20-2004, 07:47 AM | #5 |
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
You guys tell him to keep his quadrajet, but since he's talking about studs holding the carb down, my money says he has a 2 barrel Rochester carb, not a quadrajet.
Just the same, a 2 barrel Rochester is my all time favoritest carb ever. Have it rebuilt properly, install a good filter right before it and you should be good to go. Those carbs are as reliable as the family dog.
__________________
I'm on the Instagram- @Gearhead_Kevin |
12-20-2004, 02:33 PM | #6 |
Cantankerous Geezer
Join Date: Aug 2002
Location: Bel Aire, KS
Posts: 6,264
|
You can buy the studs at an auto parts store or a hardware store. To remove the old studs, put two nuts on the stud as far down as possible and tighten them against each other. Then turn the bottom nut to unscrew the stud. If the stud doesn't turn, heat the manifold around the stud with a torch, if you're using propane it will take a while. You should then be able to back the stud out.
I agree with the others, for a daily driver the Rochester will be your best bet. You might have a leaky throttle shaft, whiich will need to have a bushing installed.
__________________
Fred There is no such thing as too much cam...just not enough engine. |
12-20-2004, 11:41 PM | #7 | |
Registered User
Join Date: Nov 2004
Location: "Under Montana skies."
Posts: 1,836
|
Quote:
OK, maybe I was imagining Q-jet.
__________________
'71 GMC K20 Suburban, '71 GMC K10 Suburban, '72 Chevy C10 CST Suburban, '72 Chevy K20 clunker pickup. |
|
12-21-2004, 12:07 AM | #8 |
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
I've run into the carb studs being corroded and necked down badly. My advice, if the nut will thread down onto it, leave it alone.
A carb does not need much torque on the holdown nuts. There is no reason to tighten it very tightly. That's why there is a gasket under there, to seal the carb. No tighter than you need to cinch them down, don't risk ruining a stud trying to pull them out. I bet it's a cast iron manifold and I bet the stud seized in there tighter than heck. You'll likely get to learn about such neat things as easy-outs, drill bits and taps if you mess with it.
__________________
I'm on the Instagram- @Gearhead_Kevin |
12-21-2004, 08:33 PM | #9 |
Dave's not here, man
Join Date: Jun 2004
Location: Winder, Georgia
Posts: 2,000
|
Thank you all very much for your advice. I think I'll try and have it rebuilt by someone locally. They sell the reman. Rochester 2 bbl. for about $110 at the parts house, and a rebuild around here seems to go for about $100... six to one, half a dozen to the other. I'll keep you posted. THANKS AGAIN!!!
|
12-21-2004, 10:10 PM | #10 |
Registered User
Join Date: Apr 2004
Location: Clanton, AL
Posts: 1,253
|
Although... if he has problems removing the old carb studs, thats a perfect excuse to put in a nice aluminum intake. It'll give you a littl more power & run cooler air/fuel mix, resulting in slightly better gas mileage. You should be able to find a nice used Performer on here or ebay for 35-45'ish.
But, don't listen to me. I'm always looking for an excuse to break stuff. Especially if its properly working.
__________________
85' CUCV M1009!!! The newest addition! 6.2diesel, Th400, NP208, & only 36k miles! 70' C-10 LWB Fleetside - Looking good these days! 05' Dodge Neon 88' Winner Escape Sport 1750 - 4.3v6 94' Seadoo SP 84' Honda TRX200, bare nekkid. Just a frame & tires. Always looking for another project or any good deal! |
12-21-2004, 10:13 PM | #11 |
Watch out for your cornhole !
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
|
He's got a 2 barrel.
__________________
I'm on the Instagram- @Gearhead_Kevin |
12-23-2004, 10:54 PM | #12 |
Registered User
Join Date: May 2003
Location: Shreveport LA
Posts: 3,170
|
The local rebuild is the best bet. That way you get the same carb back & it's already calibrated for your vehicle (assuming it was right beforehand), and everything hooks up the same way, in the same place.
|
Bookmarks |
|
|