55.2-59 What is this - The 1947 - Present Chevrolet & GMC Truck Message Board Network

MD2020 · 10-09-2022, 01:34 AM

What are these hole for??
4 holes

I'm about to weld these up

_Ogre · 10-09-2022, 01:08 PM

turn signal rubber plug inserts (both sides), similar to headlight plugs in inner fenders
horn i believe

ndeep · 10-09-2022, 08:37 PM

been a few years since i built mine, but if you plan on running vintage air i think you use those holes for reference points. not certain but check before you weld them up

MD2020 · 10-10-2022, 07:51 AM

Quote:

Originally Posted by ndeep

been a few years since i built mine, but if you plan on running vintage air i think you use those holes for reference points. not certain but check before you weld them up

When I took this picture I was mocking up the vintage air condenser and drier, I don't need those holes, I have the Compact Gen 2 system.

So there are blinkers that go there also?? My blinkers are under the head lights

**joedoh** · 10-10-2022, 11:43 AM

Quote:

Originally Posted by MD2020

So there are blinkers that go there also?? My blinkers are under the head lights

i think those holes are how the wiring exits the engine compartment TO the blinkers under the headlights.

_Ogre · 10-10-2022, 01:12 PM

Quote:

Originally Posted by joedoh

i think those holes are how the wiring exits the engine compartment TO the blinkers under the headlights.

correct. the body harness has a rubber female plug that fits in the hole, the light in the grill has a corresponding male plug that fits in the plug. my 58 the holes are a little lower, one of the vintage air hard lines went thru the right hole

MD2020 · 10-10-2022, 08:50 PM

Thanks guy's
No need to weld them up because you can not see them with the upper grill panel and hood latch

MD2020 · 10-25-2022, 07:27 PM

So what are those 4 louvers on each side for?? 1st picture
The Hood latch panel and upper grill panel bar hide them from being seen.
Does the horn sound come out there??

My truck was missing lot's of parts when I got it so It took me a while to figure out things.

10-09-2022, 01:34 AM	#1
MD2020 Registered User Join Date: Sep 2018 Location: Batesville,MISSISSIPPI Posts: 312	What is this What are these hole for?? 4 holes I'm about to weld these up Attached Images

10-09-2022, 01:08 PM	#2
_Ogre Registered User Join Date: Jan 2012 Location: Motown Posts: 7,667	Re: What is this turn signal rubber plug inserts (both sides), similar to headlight plugs in inner fenders horn i believe __________________ cool, an ogre smiley Ogre's 58 Truk build how to put your truck year and build thread into your signature shop air compressor timer

10-09-2022, 08:37 PM	#3
ndeep Registered User Join Date: Jan 2016 Location: Walnut Hill,Il Posts: 56	Re: What is this been a few years since i built mine, but if you plan on running vintage air i think you use those holes for reference points. not certain but check before you weld them up

10-10-2022, 08:50 PM	#7
MD2020 Registered User Join Date: Sep 2018 Location: Batesville,MISSISSIPPI Posts: 312	Re: What is this Thanks guy's No need to weld them up because you can not see them with the upper grill panel and hood latch

10-25-2022, 07:27 PM	#8
MD2020 Registered User Join Date: Sep 2018 Location: Batesville,MISSISSIPPI Posts: 312	Re: What is this So what are those 4 louvers on each side for?? 1st picture The Hood latch panel and upper grill panel bar hide them from being seen. Does the horn sound come out there?? My truck was missing lot's of parts when I got it so It took me a while to figure out things.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.