how do i get it to hook? - The 1947 - Present Chevrolet & GMC Truck Message Board Network

67chevypickup · 08-29-2002, 06:56 PM

im new to this board, need a little help with my pickup. this is all for my senior project for high school, im starting a year ahead of time to get what i want done.the truck is a 67 chevy shortwheelbase fleetside pickup. the engine is already taken care of, its in my signature. the engine will be putting out around 450 horsepower and 460-480 lb feet of torque so i know traction is going to be a problem. im already planning on bfg drag radials, im moving the gas tank from behind the seat to inside the bed, other than that im not sure of what to do. with this much torque im not sure if that is enough. any suggestions?my goal is a 7.7-7.8 in the 1/8th. is that possible with that much power?

thanks in advance!

67

HvyChevy454 · 08-30-2002, 05:50 PM

tub it out, put polyurethane bushings in, put the battery in the bed, get rid of all the unnecessary stuff under the hood, heater, ac, wheel wells, fritn bumper then if you really wanna get serious start replaceing the front sheet metal w/ fiberglass from USBody. But doing half of that makes it not a good daily driver

nate68 · 08-31-2002, 10:25 PM

you might wanna spend the extra and get some mickey thompson et streets or et drags. there was an article in car craft (i think) recently about radial ta vs. drag radial vs. et streets

08-29-2002, 06:56 PM	#1
67chevypickup Registered User Join Date: Aug 2002 Location: hertford, nc Posts: 1	how do i get it to hook? im new to this board, need a little help with my pickup. this is all for my senior project for high school, im starting a year ahead of time to get what i want done.the truck is a 67 chevy shortwheelbase fleetside pickup. the engine is already taken care of, its in my signature. the engine will be putting out around 450 horsepower and 460-480 lb feet of torque so i know traction is going to be a problem. im already planning on bfg drag radials, im moving the gas tank from behind the seat to inside the bed, other than that im not sure of what to do. with this much torque im not sure if that is enough. any suggestions?my goal is a 7.7-7.8 in the 1/8th. is that possible with that much power? thanks in advance! 67 __________________ 67chevy pickup, 383 stroker, comp cams xr276hr hydraulic roller, pro action 200cc angle plug heads with 2.08/1.60 valves, ported performer rpm intake, 650 holley double pumper, 9.7-1 compression, th350with trans go shift kit, 3.73 rear end.

08-30-2002, 05:50 PM	#2
HvyChevy454 Slowly getting CRSS... Join Date: Jul 2001 Location: Lutz, Florida Posts: 656	tub it out, put polyurethane bushings in, put the battery in the bed, get rid of all the unnecessary stuff under the hood, heater, ac, wheel wells, fritn bumper then if you really wanna get serious start replaceing the front sheet metal w/ fiberglass from USBody. But doing half of that makes it not a good daily driver __________________ -Nic Lutz, Fl My Team Website The Heavy Chevy Website ------------------ 72 Cheyenne 10 LWB GM 12-bolt 3.08 w/ Auburn Posi 91 454 Edel Performer RPM Intake 750 cfm carb Comp Cam 268/.495 Hedman Headers Dual 3'' Exhaust 71 Cheyenne 20 4x4 Fact. A/C PS PB Tilt Currently in the works... Speak Softly and Carry A Big Block... There is No replacement for Displacement... "If everything seems under control, you're just not going fast enough." - Mario Andretti

08-31-2002, 10:25 PM	#3
nate68 Registered User Join Date: Jan 2000 Location: ca Posts: 1,110	you might wanna spend the extra and get some mickey thompson et streets or et drags. there was an article in car craft (i think) recently about radial ta vs. drag radial vs. et streets __________________ 68 short step, 406/700r4, 9" w/discs.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.