The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1988 - 1998 Chevy & GMC Pickups Message Board > projects and builds 88-98

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-29-2018, 01:02 AM   #101
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Trial fit the ram air cowl hood today. Now itís time to cut a hole in the front scoop and make the ram air functional
Attached Images
 
fredscarryall is offline   Reply With Quote
Old 03-31-2018, 02:09 AM   #102
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Ram air hood is now functional
Attached Images
    
fredscarryall is offline   Reply With Quote
Old 03-31-2018, 02:36 AM   #103
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

I used a moroso 97070 air pan foam,k&n 03351 base plate,air 801-452 air filter,k&n 14Ēx4 air filter(filters stacked on top of each other),and a k&n 66-1100 x-stream 11Ē top filter
Attached Images
     
fredscarryall is offline   Reply With Quote
Old 03-31-2018, 02:48 AM   #104
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Also used a 16Ē deep dish pizza pan, had to extend the center carb stud with spectre 42133 air cleaner stud kit, aluminum gutter screen,a piece of 1/8 3íx3í sheet of aluminum and then anchored it down with #10 self tappers. Its solid and doesnít flex at all
Attached Images
   
fredscarryall is offline   Reply With Quote
Old 04-03-2018, 12:09 AM   #105
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Finally got a decent day to take some picture with all the recent upgrades
Attached Images
     
fredscarryall is offline   Reply With Quote
Old 04-03-2018, 01:32 AM   #106
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Next is the rear roll pan with wind diffuser (I will see how close I can get to my rendering)and interior,but Iím changing the carpet and center console to black. I got the carpet from classic industries but I think I will lay some dynomat down first.Then using some bucket seats from a 2015 dodge caravan that are black with a red stitch off craiglist for $200 ( I just have to figure out what wires goes to the side air bags and not hook them up). For all the purist. I am still saving everthing. So no 454ssís were harmed in these mods.
Attached Images
     

Last edited by fredscarryall; 04-03-2018 at 01:56 AM.
fredscarryall is offline   Reply With Quote
Old 04-05-2018, 12:07 AM   #107
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Mocked up the fiberglass roll pan I got off amazon today. Fits pretty good for fiberglass.Now I have to take it off to install the diffuser fins and paint it.
Attached Images
 

Last edited by fredscarryall; 04-05-2018 at 12:13 AM.
fredscarryall is offline   Reply With Quote
Old 04-16-2018, 12:42 AM   #108
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Painted the rear roll pan. I though I would give a preval sprayer a tray again.I sprayed a single stage urethane. Works really well. Not bad for $12 including a rustoleum hand sprayer from Home Depot (I went through 1 sprayer with a jar and 1 refill) I used this same sprayer when I painted a hood a few years ago. Just make sure you use a high end primer no rustoleum or dulicolor.You donít need any special filters and you throw the air sprayer cartridge away after your done. Great alternative to someone who doesnít have a compressor.Gives you a little bit of orange peel over a real spray gun. But I was planning on cutting and buffing it anyway. Next I will double stick the air fins.
Attached Images
    
fredscarryall is offline   Reply With Quote
Old 04-16-2018, 12:54 AM   #109
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Final results on the the roll pan sprayer with the preval sprayer. This week is the hood. I going to spray the hood with a $27 harbor freight gun with 20% off coupon.I did a firewall a few years ago with this same gun and it turn out awesome.
Attached Images
   
fredscarryall is offline   Reply With Quote
Old Today, 01:13 AM   #110
fredscarryall
Registered User
 
fredscarryall's Avatar
 
Join Date: Feb 2010
Location: gresham oregon
Posts: 729
Re: Fastfreddys 454ss

Taught my 17 year old neighbor how to paint a hood today. Turn out perfect. Had a little freight damage that I had to take care of first. Next week I’m going to tint the windows. Then start on the interior. Going to install the black carpet, dynomat the floor, finish wiring the sound system, replace the seats and dye the door panels black that I got off ebay. There goes another tote to fill with the factory stock parts. Should take about a week on the interior. Then comes the engine performance mods.
Attached Images
   

Last edited by fredscarryall; Today at 01:38 AM.
fredscarryall is offline   Reply With Quote
Old Today, 09:57 AM   #111
arrg
Registered User
 
Join Date: Feb 2016
Location: Omaha, NE
Posts: 28
Re: Fastfreddys 454ss

What paint are you using?
__________________
1988 Chevrolet C1500 RCSB
arrg is offline   Reply With Quote
Old Today, 02:57 PM   #112
jjzepplin
Senior Member
 
jjzepplin's Avatar
 
Join Date: Feb 2012
Location: Riverview Florida
Posts: 3,333
Re: Fastfreddys 454ss

That's nice!
__________________
70 swb 4x4 406sbc 700r4 203/205 d60/14blt locker yadda yadda http://67-72chevytrucks.com/vboard/s...88#post6935688
72 Blazer 2wd conversion project "No Daggum Money" http://67-72chevytrucks.com/vboard/s...d.php?t=550804 3.73 posi-4-speed Saginaw-307-no budget build.
58 Belair http://67-72chevytrucks.com/vboard/s...d.php?t=756563
jjzepplin is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 08:33 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright 1997-2013 67-72chevytrucks.com