Project Grande Slam: Coley's Hot Rod Shop - Page 5 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**CC69Rat** · 03-19-2012, 11:23 AM

I wish I could do the billets that Stiney had, .. but I just can't on a daily driver and the truck will be sitting outside too. I will probably do the gray Coys just so they're easier to take care of and that's one of my favorite wheels ever.

20" Salt flats would be cool too.. not sure just yet. Still open for a used set. I'm hoping someone will want to freshen theirs up and sell a good setup soon.

There's a reason IMO a lot of people have the Coys and TTIIs They just look cool on old trucks. I'd put them on my lawnmower if I could.

72BlckButy · 03-19-2012, 02:04 PM

IMO... skip the rear discs.

NoNeck · 03-19-2012, 04:02 PM

With a limited budget, I would start off by dropping it!

Purchase a 5 lug disk brake conversion kit with 2" (or 2.5") drop spindles and 2" lowering springs. For now, change over to 5 lug rear axles, and drop the rear as much as possible without a c-notch (5" or 6"?). Maybe when you are ready to remove the bed, we can detail the frame and add rear disks? With this truck being a daily driver, you really don't want it scraping across speed bumps and curbs.

You could even run the 5 lug Rallys from your Big Block truck until you get your 20's if cash was a little low. This would eliminate those "grandpa" whitewalls and get the truck out of the nose bleed section.

POP

**CC69Rat** · 03-22-2012, 01:13 PM

Step One ! - Tires came in yesterday

Thinking about this wheel for the GMC? Raceline Burst

VA72C10 · 03-22-2012, 01:26 PM

Truck is looking good. I agree...skip the rear discs. And...while I like those Racelines...they don't seem to "fit" the look of the truck (light patina nice original) I think the coys, tt2's or similar would fit the truck better....just MHO though

Still hoping to swing by and see both your trucks sometime either on my way down or back again this time. last time I came back late at night with my sister in law and her daughter in the van so that was a no-go

Pm me your dad's address and I'll try to figure out how to work it into my schedule and see if we can meet up there sometime.

**67cheby** · 03-22-2012, 02:19 PM

Wheels are BEAUTIFUL !!!

big_al_71 · 03-22-2012, 04:22 PM

very nice looking wheels.....

shawno72 · 03-22-2012, 04:34 PM

Quote:

Originally Posted by CC69Rat

Step One ! - Tires came in yesterday

Thinking about this wheel for the GMC? Raceline Burst

How much do those run?

**CC69Rat** · 03-22-2012, 04:35 PM

Still undecided on the wheels, saving a little money up and I'll get them soon. It wouldn't make sense really to put billets on a driver that will have to sit outside.. I'll probably stay with a cast wheel of some sort.

Not sure what I'll get yet ..

**CC69Rat** · 03-22-2012, 04:43 PM

Oh, the Racelines are only $549 ea for the 20x8.5

Guess those are out ..

shawno72 · 03-22-2012, 04:46 PM

Quote:

Originally Posted by CC69Rat

Oh, the Racelines are only $549 ea for the 20x8.5

Guess those are out ..

raull · 03-22-2012, 05:17 PM

ok chad , i last posted on 2/13 on the big block truck, did you forget about that truck, he is feeling neglected buddy , lol

**CC69Rat** · 03-22-2012, 05:25 PM

I actually called the paint store this morning to price my grille / top paint for it. I haven't forgotten

.. but I did kinda borrow the fuel return spring off of it for my GMC the other day. I honestly felt bad for doing it.

Oh, no .. I haven't forgotten about it. Just trying to get the GMC in 'driver' condition then it's back to the 68. The funds are coming from a difference source on this truck than the BB truck too so that will help.

Momma keeps me pretty busy around the house too. She asked me this morning.. "When are you going to start the ceramic tile project in the kitchen?"

shawno72 · 03-22-2012, 05:33 PM

Tell her right after you finish a little something in the garage

raull · 03-22-2012, 07:32 PM

Quote:

Originally Posted by shawno72

Tell her right after you finish a little something in the garage

agree !!!

LakeAnna · 03-23-2012, 09:03 PM

Quote:

Originally Posted by CC69Rat

Step One ! - Tires came in yesterday

Thinking about this wheel for the GMC? Raceline Burst

Yeah! They would look awesome on your "driver".... BTW did you finish the tile yet?

My Dad always said "if momma aint happy... NObody is happy"

CROWN · 03-23-2012, 09:46 PM

Quote:

Originally Posted by CC69Rat

Oh, the Racelines are only $549 ea for the 20x8.5

Guess those are out ..

Where did you find that price at?? I looked on Racelines website and prices weren't listed. You can pm me if need be.
Posted via Mobile Device

**CC69Rat** · 03-24-2012, 11:53 AM

Took some more pictures today .. thought you might like to see.

**CC69Rat** · 03-24-2012, 11:54 AM

more ..

**CC69Rat** · 03-24-2012, 12:00 PM

I think the truck has had rockers put in it at one point in it's life, but the cab mounts and typical rust areas look really good (to me ?)

The door panels were curling up so I can understand the metal plates on the doors. I'll tack up the holes and grind them smooth / paint and the will be tough to see. The headliner is there, but it is drooping just a tad. I'll fix that .. I think it will clean up really nice.

It does still have the black pad / cover thing over the gas tank but it has slid down over the years ..

A good upholstry shop should be able to fix that foam in the seat .. you think?

The tailgate looks really good but the bed is shot. I will be pulling the entire bed floor, replacing the rear inner wheel wells with some really good original west coast GM fender wells and all new wood bed floor / supports. The front bed panel will also be replaced.

It looks like either cheap bedliner or maybe house paint in the bed ?? It's rough ! .. but not for long.

**CC69Rat** · 03-24-2012, 12:04 PM

More ..

Talking to Special-K, this might be a Super Custom? Not sure. Can you tell? Special-K mentioned the Z84 pkg on the SPID + the custom seat / headliner might be a Super Custom specific thing. I have no idea.. I hope (and feel like) he's right!

**CC69Rat** · 03-24-2012, 12:07 PM

The driver's side still has quite a bit of orange peel on it. The pasenger side has been cut and buffed and you can definitely tell it. More to come soon! I hope to order my suspension stuff in about 10 days. I am going to collect everything and just take a week off work. Hang out with dad and just do it all at one time. Suspension, wheels, tires, sway bars, complete interior, and new wood bed floor. Just sit the truck on stands, strip it and come back up. All the parts onsite and just do it.

Anyone heading to TN anytime soon ?

Mid May - Early June?

**67cheby** · 03-24-2012, 12:11 PM

great idea getting everything there and ready to go , then just hammer it out !! I dont understand how your cab supports can be so nice and the bedfloor be so rusty !! that is weird !

**lolife99** · 03-24-2012, 01:21 PM

Hey CC69Rat, I'm loving this truck more each time I see it.

What do the GMC fender emblems say?
Also,... if you change interior color,... I will be interested in a good set of '70 Gold seat belts. Keep me in mind.

Also another question for the GMC experts.
What year were the "nicer" side marker lights available on the GMC's? (71-72 only?)
Should your marker lights be the plain red and yellow version?
Or are those correct?

shawno72 · 03-24-2012, 01:35 PM

I love how the a/c has the deluxe knobs.

03-19-2012, 11:23 AM	#101
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop I wish I could do the billets that Stiney had, .. but I just can't on a daily driver and the truck will be sitting outside too. I will probably do the gray Coys just so they're easier to take care of and that's one of my favorite wheels ever. 20" Salt flats would be cool too.. not sure just yet. Still open for a used set. I'm hoping someone will want to freshen theirs up and sell a good setup soon. There's a reason IMO a lot of people have the Coys and TTIIs They just look cool on old trucks. I'd put them on my lawnmower if I could. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-19-2012, 02:04 PM	#102
72BlckButy Tot Roddin' Join Date: Apr 2005 Location: Mid-MO Posts: 24,461	Re: Project Grande Slam: Coley's Hot Rod Shop IMO... skip the rear discs. __________________ -Nate 1969 CST SWB - Project Blank Slate (4.5/6" ECE Static Drop, 6-lug disc brake upgrade (manual), Billet Specialties Vintec 20x8.5 255/40 (F) 20x10 295/40 (R), 250 I-6) 1960 AMF Skylark - Tot Roddin' (Lowered with custom frame; soon to include custom push bar and interior) 2008 Silverado CrewCab 1LT (5.3L, 3:73, 4x4, LT1, Z-71, Towing Package)

03-19-2012, 04:02 PM	#103
NoNeck Registered User Join Date: Jan 2011 Location: Chattanooga, TN Posts: 1,105	Re: Project Grande Slam: Coley's Hot Rod Shop With a limited budget, I would start off by dropping it! Purchase a 5 lug disk brake conversion kit with 2" (or 2.5") drop spindles and 2" lowering springs. For now, change over to 5 lug rear axles, and drop the rear as much as possible without a c-notch (5" or 6"?). Maybe when you are ready to remove the bed, we can detail the frame and add rear disks? With this truck being a daily driver, you really don't want it scraping across speed bumps and curbs. You could even run the 5 lug Rallys from your Big Block truck until you get your 20's if cash was a little low. This would eliminate those "grandpa" whitewalls and get the truck out of the nose bleed section. POP __________________ 2016 RAM Laramie HEMI 1966 Fairlane GT/A, 390/335 HP If it costs you a dollar to make a friend, KEEP THE DOLLAR. If it costs you a friend to make a dollar, KEEP THE FRIEND.

03-22-2012, 01:13 PM	#104
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop Step One ! - Tires came in yesterday Thinking about this wheel for the GMC? Raceline Burst Attached Images __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-22-2012, 01:26 PM	#105
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project Grande Slam: Coley's Hot Rod Shop Truck is looking good. I agree...skip the rear discs. And...while I like those Racelines...they don't seem to "fit" the look of the truck (light patina nice original) I think the coys, tt2's or similar would fit the truck better....just MHO though Still hoping to swing by and see both your trucks sometime either on my way down or back again this time. last time I came back late at night with my sister in law and her daughter in the van so that was a no-go Pm me your dad's address and I'll try to figure out how to work it into my schedule and see if we can meet up there sometime. __________________ Looking for a 67-72 swb or blazer project in or around VA.

03-22-2012, 02:19 PM	#106
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project Grande Slam: Coley's Hot Rod Shop Wheels are BEAUTIFUL !!! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-22-2012, 04:22 PM	#107
big_al_71 Registered User Join Date: Jun 2008 Location: South Florida Posts: 11,375	Re: Project Grande Slam: Coley's Hot Rod Shop very nice looking wheels..... __________________ Get your facts first, and then you can distort them as much as you please!!!!!. Sylvester's build thread >>>http://67-72chevytrucks.com/vboard/s...ht=big+rebuild

03-22-2012, 04:35 PM	#109
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop Still undecided on the wheels, saving a little money up and I'll get them soon. It wouldn't make sense really to put billets on a driver that will have to sit outside.. I'll probably stay with a cast wheel of some sort. Not sure what I'll get yet .. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-22-2012, 04:43 PM	#110
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop Oh, the Racelines are only $549 ea for the 20x8.5 Guess those are out .. __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-22-2012, 05:17 PM	#112
raull Registered User Join Date: Mar 2009 Location: miramar florida Posts: 1,232	Re: Project Grande Slam: Coley's Hot Rod Shop ok chad , i last posted on 2/13 on the big block truck, did you forget about that truck, he is feeling neglected buddy , lol __________________ check out my build thread 71 c/10 step side 5.3 twin turbo http://67-72chevytrucks.com/vboard/s...d.php?t=485320 raul

03-22-2012, 05:25 PM	#113
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop I actually called the paint store this morning to price my grille / top paint for it. I haven't forgotten .. but I did kinda borrow the fuel return spring off of it for my GMC the other day. I honestly felt bad for doing it. Oh, no .. I haven't forgotten about it. Just trying to get the GMC in 'driver' condition then it's back to the 68. The funds are coming from a difference source on this truck than the BB truck too so that will help. Momma keeps me pretty busy around the house too. She asked me this morning.. "When are you going to start the ceramic tile project in the kitchen?" __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-22-2012, 05:33 PM	#114
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: Project Grande Slam: Coley's Hot Rod Shop Tell her right after you finish a little something in the garage __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

03-24-2012, 11:53 AM	#118
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop Took some more pictures today .. thought you might like to see. Attached Images __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-24-2012, 11:54 AM	#119
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop more .. Attached Images __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-24-2012, 12:00 PM	#120
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop I think the truck has had rockers put in it at one point in it's life, but the cab mounts and typical rust areas look really good (to me ?) The door panels were curling up so I can understand the metal plates on the doors. I'll tack up the holes and grind them smooth / paint and the will be tough to see. The headliner is there, but it is drooping just a tad. I'll fix that .. I think it will clean up really nice. It does still have the black pad / cover thing over the gas tank but it has slid down over the years .. A good upholstry shop should be able to fix that foam in the seat .. you think? The tailgate looks really good but the bed is shot. I will be pulling the entire bed floor, replacing the rear inner wheel wells with some really good original west coast GM fender wells and all new wood bed floor / supports. The front bed panel will also be replaced. It looks like either cheap bedliner or maybe house paint in the bed ?? It's rough ! .. but not for long. Attached Images __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)



Register or Log In To remove these advertisements.

03-24-2012, 12:04 PM	#121
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop More .. Talking to Special-K, this might be a Super Custom? Not sure. Can you tell? Special-K mentioned the Z84 pkg on the SPID + the custom seat / headliner might be a Super Custom specific thing. I have no idea.. I hope (and feel like) he's right! Attached Images __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-24-2012, 12:07 PM	#122
CC69Rat Senior Member Join Date: Jan 2011 Location: Chattanooga TN Posts: 6,205	Re: Project Grande Slam: Coley's Hot Rod Shop The driver's side still has quite a bit of orange peel on it. The pasenger side has been cut and buffed and you can definitely tell it. More to come soon! I hope to order my suspension stuff in about 10 days. I am going to collect everything and just take a week off work. Hang out with dad and just do it all at one time. Suspension, wheels, tires, sway bars, complete interior, and new wood bed floor. Just sit the truck on stands, strip it and come back up. All the parts onsite and just do it. Anyone heading to TN anytime soon ? Mid May - Early June? __________________ Chad 1967 C10 SWB - Project Savannah - 6.0/4L80 Currently underway 1968 C10 SWB - TOTY 2018, 50th Anniversary Tribute Project * Sold * Pride and Joy 1986 Silverado Short Fleet - Scarlet Sold 1985 Silverado Short Fleet Sold 2022 Jeep Gladiator Mojave 2001 Jeep Cherokee XJ 4x4 - Lifted, Built 1992 Jeep Cherokee XJ 4x4 - Lifted 2013 Honda Accord EX-L v6 Coupe 6spd (wife's ride)

03-24-2012, 12:11 PM	#123
67cheby 67cheby Join Date: Sep 2008 Location: siloam springs ar 72761 Posts: 17,890	Re: Project Grande Slam: Coley's Hot Rod Shop great idea getting everything there and ready to go , then just hammer it out !! I dont understand how your cab supports can be so nice and the bedfloor be so rusty !! that is weird ! __________________ Check out Slosh Tubz, bolt-in inner fenders for frame laying C-10's Slosh Tubz Introductory Price $559 67 Cheby's Dropmember Build Thread Slosh Tubz on Facebook http://67-72chevytrucks.com/vboard/s...d.php?t=554172

03-24-2012, 01:21 PM	#124
lolife99 67-72 parts collector,… Join Date: Nov 2002 Location: Mid-MO Posts: 22,681	Re: Project Grande Slam: Coley's Hot Rod Shop Hey CC69Rat, I'm loving this truck more each time I see it. What do the GMC fender emblems say? Also,... if you change interior color,... I will be interested in a good set of '70 Gold seat belts. Keep me in mind. Also another question for the GMC experts. What year were the "nicer" side marker lights available on the GMC's? (71-72 only?) Should your marker lights be the plain red and yellow version? Or are those correct? __________________ Keith Convert to disc brakes. http://67-72chevytrucks.com/vboard/s...d.php?t=444823

03-24-2012, 01:35 PM	#125
shawno72 C/10 junkie Join Date: Nov 2010 Location: Stockton Ca Posts: 9,093	Re: Project Grande Slam: Coley's Hot Rod Shop I love how the a/c has the deluxe knobs. __________________ Shawn 70 LWB C10 current driver/project http://67-72chevytrucks.com/vboard/s...d.php?t=663051 68 SWB C10 Work in progress.....SOLD http://67-72chevytrucks.com/vboard/s...d.php?t=559520 72 LWB C10 Sold 71 LWB C10 Sold 68 LWB C10 CST Sold http://youtu.be/kbB0QrBIs9k My mom always had the best advice. It was just a tad late. After a fall that involved blood, she'd say....."Careful!"

Register or Log In To remove these advertisements.