The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1960 - 1966 Chevrolet & GMC Pickups Message Board > projects and builds

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-15-2017, 01:38 AM   #1
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
1962 C20 ... long way from home

I recently bought this C20, running manual tranny and a 327. I have been daily driving it for the past month, its wintery here in NZ right now.

Plan is an LS3 and 6L80 conversion (sitting in the shed), I am going 5 lug all the way around, I have a 70's C10 front end a 12 bolt rear, aircon, rewire... bed is currently non existent, lucky I have a mate who makes timber mouldings, so he will run the decking timber for me and I will reuse the old steel strips cleaned up a bit.

It will be signwritten, all the dings and dents will be left and it will be my daily driver. Chassis is in for blasting and painting in a week.





sluggy is offline   Reply With Quote
Old 07-17-2017, 12:50 AM   #2
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 20,472
Re: 1962 C20 ... long way from home

Welcome to the forum

That looks like a decent truck to work with.
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old 09-26-2017, 03:40 PM   #3
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
Re: 1962 C20 ... long way from home

Making some progress on this. Tray is off, front end off, replaced the floor pans as they were a bit holey, front seat is being reupholstered. Had the frame sand blasted and rust proofed/sprayed. I have removed the 327, and am currently working out mounts etc for the engine. I had bought the front end out of a 77 truck, but looks like I dont need to change the front end, even with the 6l80 trans there is plenty of space between the torsion bar crossmember and the rear of the trans. Also had a mate who machines timber run up some American oak for the deck.

At this stage I am looking to use the 77 perches, and fill the gap between these and the frame rails (pic is just a rough mock up !), and still need to fab up some brackets from the frame rails to the tranny mount.

Can anyone give me some direction on setting up the trans output angle and height in relation to the centre bearing (2 piece tailshaft) ? I should have measured the height of the old trans before removal, but forgot too ...
Heres some pics
Attached Images
    
sluggy is offline   Reply With Quote
Old 09-26-2017, 03:59 PM   #4
jchav62
1962 C-10
 
jchav62's Avatar
 
Join Date: Apr 2005
Location: Albuquerque, New Mexico
Posts: 4,600
Re: 1962 C20 ... long way from home

Looking good!!
__________________
Joseph Chavez
"See the USA in a Chevrolet!!"
......................_____
.........________//__{\_____
,,,,,,,/__(O)___//___/__(O)_/
jchav62 is offline   Reply With Quote
Old 10-01-2017, 04:28 AM   #5
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
Re: 1962 C20 ... long way from home

Got mounts pretty much done. Trans mount is looking a bit agricultural so will likely make some changes with this. But it is getting there. Pretty happy that I have the angle sorted for the first section of drive shaft.
Attached Images
  
sluggy is offline   Reply With Quote
Old 11-08-2017, 05:45 AM   #6
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
Re: 1962 C20 ... long way from home

Getting closer...80 % rewired, brakes to do, and interior to button up...
Attached Images
   
sluggy is offline   Reply With Quote
Old 11-20-2017, 03:59 PM   #7
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
Re: 1962 C20 ... long way from home

Got the seat back from upholstery, wiring is done but cant get it started so my friendly auto electrical mate is coming today to hopefully get it fired up. I have changed the spindles C20 - C10 classic industries spindles and their brake kit. Just need to rebuild the rear drums. Aircon is complete baring gassing up.

So not far off being back on the road after 2 months of working on it.
Attached Images
  
sluggy is offline   Reply With Quote
Old 01-17-2018, 05:05 PM   #8
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
Re: 1962 C20 ... long way from home

Havent updated this in a while. But its all running and back together. See pics below.
Running sweetly now apart from a fuel issue, I bought a relocate tank for the 62 from POL. The outlet is at the front lower passengers side. I didn't check, but there is no pick up tube, so 3/4 of a tank or less and you stand on it or go around a RH bend with your foot in it and it starves... Apparently the tank is baffled (didnt check) and they have a pick up tube they can supply. Just a heads up if you go down that route. Im going to put a surge tank in to alleviate the issue for ever.
Just did a 200 mile trip in it, ran flawlessly...
Attached Images
    
sluggy is offline   Reply With Quote
Old 01-17-2018, 06:35 PM   #9
clarsen
Registered User
 
Join Date: Jan 2017
Location: Belton MO
Posts: 17
Re: 1962 C20 ... long way from home

Nice job! You made quick work of that powertrain swap.
clarsen is offline   Reply With Quote
Old 01-17-2018, 06:51 PM   #10
The Rocknrod
Senior Member
 
The Rocknrod's Avatar
 
Join Date: Aug 2011
Location: China Spring, TX
Posts: 2,112
Re: 1962 C20 ... long way from home

And wheels? The wood looks terrific.
The Rocknrod is offline   Reply With Quote
Old 01-17-2018, 07:23 PM   #11
Rusty63
Registered User
 
Rusty63's Avatar
 
Join Date: Sep 2017
Location: Kincardine,Ontario
Posts: 25
Re: 1962 C20 ... long way from home

very nice work!
Rusty63 is offline   Reply With Quote
Old 01-18-2018, 12:44 AM   #12
Captainfab
60-66 Nut

 
Join Date: Mar 2007
Location: Coeur d'Alene, Idaho
Posts: 20,472
Re: 1962 C20 ... long way from home

Looks good Nicely done.
__________________
Power Steering Box Adapter Plates For Sale HERE
Power Brake Booster Adapter Brackets For Sale '63-'66 HERE and '67-'72 HERE and '60-'62 HERE and "60-'62 with clutch HERE
Rear Disc Brake Brackets For Sale. Impala SS calipers HERE Camaro Calipers HERE D52 Calipers HERE 6 Lug HERE
Hydroboost Mounting Plates HERE
Captainfab is offline   Reply With Quote
Old 01-18-2018, 09:32 PM   #13
sluggy
Registered User
 
Join Date: Mar 2017
Location: Auckland, NZ
Posts: 13
Re: 1962 C20 ... long way from home

Quote:
Originally Posted by The Rocknrod View Post
And wheels? The wood looks terrific.
Detroit steel wheels. 20 x9 at the rear 20 x 8 on the front. 295/40/20 rears 265/50/20 fronts (from memory). Just left them raw steel at the moment, get some natural patina on them and seal them up is the plan.

Rides really nice, But im going to put some sway bars on front and rear, fronts are marginally wrong, another 1/2" backspace wouldve been nice, they scrape a bit on our roads here. We have a lot of two lane twisty turny stuff outside of the cities.
sluggy is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 04:35 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright 1997-2013 67-72chevytrucks.com