Installing truck floorpan in blazer - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**pound41** · 12-06-2016, 09:57 AM

Has anyone cut down a new truck floor pan and installed in their blazer.
Thinking of having a try. I have all the patch panels but will have to replace more than 1/2 thats a lot of welding

BlazerLegacy · 12-06-2016, 04:42 PM

Following

hemi43 · 12-06-2016, 05:04 PM

How bad is your floor ? I replaced the rear half of mine and it wasn't difficult at all.

71meangreenc10 · 12-06-2016, 06:04 PM

I took a used floor pan and spliced it into my blazer mess. Worked fine so far.

Smitty

**pound41** · 12-07-2016, 05:49 PM

the perfect storm so to speak typical rot where the floor seams with the cowl. Outer rockers are gone some rust spots along the ridge where the front seat connects. Area where the front seat latch down sits had several small rust hole and the flat area badly pitted. Drivers side much the same. Its a weird blazer in that the inner b pillar is pretty much in tact, The little bracket under the floor at the knee wall is gone. I have the floor pan from an Arizona blazer that is fairly complete but needs some repairs as well. Body on the blazer is pretty good. Its a late 60 early 70 that is fairly well optioned so I want to do it right

12-06-2016, 09:57 AM	#1
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,267	Installing truck floorpan in blazer Has anyone cut down a new truck floor pan and installed in their blazer. Thinking of having a try. I have all the patch panels but will have to replace more than 1/2 thats a lot of welding

12-06-2016, 04:42 PM	#2
BlazerLegacy Registered User Join Date: Feb 2013 Location: Rome, GA Posts: 33	Re: Installing truck floorpan in blazer Following __________________ Zac 1970 Factory 2wd Blazer

12-06-2016, 05:04 PM	#3
hemi43 Registered User Join Date: Mar 2015 Location: Ontario Canada Posts: 1,497	Re: Installing truck floorpan in blazer How bad is your floor ? I replaced the rear half of mine and it wasn't difficult at all.

12-06-2016, 06:04 PM	#4
71meangreenc10 Its a Truck Thing...... Join Date: Dec 2004 Location: Sierra Vista, Arizona Posts: 3,158	Re: Installing truck floorpan in blazer I took a used floor pan and spliced it into my blazer mess. Worked fine so far. Smitty __________________ 71 C10 283/3SPD Full Resto 71 GMC 1500 Sierra Grande http://67-72chevytrucks.com/vboard/s...d.php?t=518599 70 C10 Suburban Former military GSA truck. 72 Chevy Blazer 4X4, Sloppy Jo, Mountain Climber. Wife says no more trucks. http://67-72chevytrucks.com/vboard/s...d.php?t=707378 72 GMC 1 Ton Motor Home, wife said no more trucks until she saw this one. Gen 3 6.0/4L80E 4.10 http://67-72chevytrucks.com/vboard/s...d.php?t=761110 68 GMC Suburban was 3/4 ton, now 1/2.Wife shook her head 71 C30 Wrecker 71 C20 Scott-Bilt As weird as it gets..BB Cheyenne AC Truck 68 GMC Long Stepside. They keep following me home 71 C20 Longhorn/Ole Yellor 69 C30 Former Motor Home, Flat Bed time

12-07-2016, 05:49 PM	#5
pound41 Registered User Join Date: Dec 2002 Location: Northern Virginia Posts: 1,267	Re: Installing truck floorpan in blazer the perfect storm so to speak typical rot where the floor seams with the cowl. Outer rockers are gone some rust spots along the ridge where the front seat connects. Area where the front seat latch down sits had several small rust hole and the flat area badly pitted. Drivers side much the same. Its a weird blazer in that the inner b pillar is pretty much in tact, The little bracket under the floor at the knee wall is gone. I have the floor pan from an Arizona blazer that is fairly complete but needs some repairs as well. Body on the blazer is pretty good. Its a late 60 early 70 that is fairly well optioned so I want to do it right

Thread Tools
Show Printable Version Email this Page
Display Modes
Linear Mode Switch to Hybrid Mode Switch to Threaded Mode



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.