TX Any need bottom end parts for 87-up SBC??

[bwood]

I would like to get rid of this stuff, here is a pic of all the bottom end parts I have:

http://i146.photobucket.com/albums/r...tecParts-1.jpg


-Federal Mogul Main Bearing Set-Standard-Part#4663MA
New-box opened but never installed $10

-Federal Mogul Rod Bearings-Standard (8)-Part #2555A
New $10

-Melling Standard Volume Oil Pump-Part #M155
New-Box opened, never installed $10

-Melling Oil Screen for above pump-Part #155S
New-Box opened, pump still in bag $5

-NAPA 3 Piece Timing Set-Part #103017
New-crank gear installed then removed-never run
Similar to Cloyes #C3017K $25

-NAPA Vortec Timing Cover-Part #600-5343
New-box opened never installed-incl plug and bolt for crankshaft sensor hole
and all new bolts for cover
Similar to Dorman #635-505 $10

-Fel Pro One Piece Oil Pan Set-Part #OS34500R
New-Never Installed, but complete $10

*The bearings, oil pan set and oil pump/screen should fit one piece rear main seal engines with truck pan V8s-verify before purchasing
*The timing cover and timing set are for 96-up Vortec V8s the timing cover will also fit 96-up Vortec also-Verify before purchasing

Everything in the pic- $50-contact for shipping cost.

Here is the rest of what I want to get rid of:

AC Delco Distributor-V6 Vortec
Bought used from a dealer w/o cam gear. I installed my old cam gear from my broken dist, make sure the gear is on correctly. Incl camshaft position sensor installed.
#???????? $20.00 obo

AC Delco Camshaft Position Sensor-Vortec
Used from old distributor-worked when removed
#10490645 $5.00

I also have the USED L30 Vortec 305 with 115k miles on it in a crate. It was running when I pulled it, it had low oil pressure and I found the main bearings and crank were in bad shape. I don’t believe that any of the bearings spun, but I only pulled #4 and #5 main caps. The engine had no knocking or ticking while running, but it did have a slight knock on start up that lasted until the oil pressure came up. I did not use any oil or smoke at all. It had 25-30 psi cold and 10-20 psi hot. This is a complete long block with valve covers and oil pan (similar to GM Goodwrench #12530284). The oil pan is bent on the pass corner from using a screwdriver to break the GM Grey RTV that the dealer put on it during a warr repair, should be easily repaired. The timing cover has been removed along with the timing set. It has no sensors or electrics. THIS IS A USED ENGINE.

I will take $75 w/ crate (the one the new engine came in, on wheels) Local Pick Up Only on this item.

All of these parts (unless otherwise noted) were purchased for my 98 305 (L30) Vortec. Parts may fit other engines/years, verify before purchasing.

I accept PayPal or check/Money Order. 2 weeks max for payment. Parts ship after payment clears. I will do local pickup, but ONLY in Denison/Sherman, Texas.

I am in Denison, Texas 75020
For PayPal use bnwood@sbcglobal.net but please do not send requests/questions to this email or PM, keep it on the thread.

[Blue_71]

i can't see the pic, but i would be interested in:

Federal Mogul Main Bearing Set-Standard-Part#4663MA
New-box opened but never installed $10

-Federal Mogul Rod Bearings-Standard (8)-Part #2555A
New $10

-Melling Standard Volume Oil Pump-Part #M155
New-Box opened, never installed $10

-Melling Oil Screen for above pump-Part #155S
New-Box opened, pump still in bag $5

Fel Pro One Piece Oil Pan Set-Part #OS34500R
New-Never Installed, but complete $10



i'll double check but all that should fit on my 89 K2500. please give me a shipped price on those to glasgow ky 42141

[bwood]

Thanks for the response. I'll have you a shipping price shortly and I fixed the link to the pic.

[bwood]

Sorry I for the late reply. I got a shipping quote but it was outrageous, $45 just for shipping (that was the cheapest between Fed Ex and UPS). They said the size of the box required to fit the pan gasket box would be so large they are going to charge for "volume weight" instead of actual weight (7.5 lbs). If it is ok with you I would like to take the pan set out of the original box, (all the gasket box contents put into a zipper bag and I will cut the label from the box so you can have the contents/fitment info) and put it all into a smaller box. Then package it all together or send it in two boxes. If this is ok with you and you are still interested, let me know.

[bwood]

Blue_71, check your PM's, I have sent you my phone #. There is another problem now. My wife's car had another break-in last night, the parts, stereo and carseat are gone.