Any one have any pics of blazer buckets and console in their truck

[BrianV]

I am thinking of buying blazer buckets and consolse for my truck and want to see if anyone else has this in their truck with some pics so i can check it out before i do it

thanks in advance

[JimKshortstep4x4]

Here is a picture of the buckets in my son's Burb. The picture is not the best but the buckets are really sharp.

Jim

[HuggerCST]

Here's mine.

[BrianV]

those are both really nice trucks - hugger did you use the vinyl dye on the console and door panels or did you order them that color

thanks alot for the pics - they look as good as i thought they would!!!

[HuggerCST]

Originally Posted by BrianV

hugger did you use the vinyl dye on the console and door panels or did you order them that color

I used SEM vinyl paint on the console & dash, but I bought the door panels, seat covers and visors that color.(sandalwood)

[jondancer]

Do these fit fine with the gas tank still in cab?
Posted via Mobile Device

[leddzepp]

Originally Posted by jondancer

Do these fit fine with the gas tank still in cab?
Posted via Mobile Device

Yes, they came from the factory that way.

[special-K]

To end any confusion in this thread,Blazer buckets are no different than truck buckets. They are the same seats. The only thing different is Blazers and Jimmys have tilt forward passenger side mounts and trucks are stationary.

[JimKshortstep4x4]

jondancer,

The tank does not interfere with the buckets. As mentioned they came from the factory with the tank in the cab.

Here is a pic of my son's 69 GMC and the tank is behind the carpet.

Jim

[screaminchevypickup]

here's the ones in my truck

[doubleb's69]

I know its an old thread but screaminchevypickup are those utility buckets in your truck? The shoulders look really square (or maybe its just the angle of the picture), was just wondering if they fit well with a console?
Also did trucks have the plastic backs on them?

[special-K]

No,trucks didn't have the plastic backs. 71/72 bucket seat backs are less tapered than 69/70s.

[VA72C10]

and a stock console won't fit between utility buckets

[z10kl]

OK, I been thinking about doing mine with buckets.
1. How do you tell the diff between utility buckets and regular?
2. Do you have to use the truck pass side brackets or will the flip forward one work?
3. If the flip ones work in a truck is it an advantage for any reason?
4. Hugger CST, what color SEM matches Sandlewood?

[Zoomin]

... And what did you guys use as far as mounting them in a bench seat truck? (seat mounts to cab)
Posted via Mobile Device

[screaminchevypickup]

Originally Posted by doubleb's69

I know its an old thread but screaminchevypickup are those utility buckets in your truck? The shoulders look really square (or maybe its just the angle of the picture), was just wondering if they fit well with a console?
Also did trucks have the plastic backs on them?

No they are regular buckets! They look the same as all the other ones in this thread!!
Posted via Mobile Device

[VA72C10]

Originally Posted by z10kl

OK, I been thinking about doing mine with buckets.
1. How do you tell the diff between utility buckets and regular?
2. Do you have to use the truck pass side brackets or will the flip forward one work?
3. If the flip ones work in a truck is it an advantage for any reason?
4. Hugger CST, what color SEM matches Sandlewood?

1) Utility buckets are very squared off and flat seat bottom cushion...no recess in the foam like the regular buckets.
2)You can use any brackets...but you will have to drill holes and then reinforce them. Either 67-72 bucket brackets (truck or blazer (not utility)) will keep the seats just below the rear window. 73-up work but are taller (nice for people with longer legs)
3) I like the blazer brackets for both driver's and passenger seats. I don't need the forward adjustment as I need the seat as far back as it can get...the tilt forward allows access behind the seat either for the gas tank....or if relocated...for storage behind the seats...and for easy access to the jack and hardware on the passenger side
4) Hopefully hugger responds...I know the SEM parchment color is too light so you have to use something else to match...

Originally Posted by Zoomin

... And what did you guys use as far as mounting them in a bench seat truck? (seat mounts to cab)
Posted via Mobile Device

I found a guy who had a set made very similar to the originals excluding the long brace....used angle iron cut to fit with capture nuts welded on for the seat to bolt into...
You could do something similar or just use large fender washers or similar to reinforce them.....

[HuggerCST]

I couldn't remember, so I had to check the can and actually it was Plastikote vinyl paint #419 buckskin.

[doubleb's69]

Originally Posted by screaminchevypickup

No they are regular buckets! They look the same as all the other ones in this thread!!
Posted via Mobile Device

Sorry, they just looked more square, like I said maybe its the angle the picture is taken. I'm new to the bucket seat world so give a newbie a break.

[special-K]

Originally Posted by doubleb's69

Sorry, they just looked more square, like I said maybe its the angle the picture is taken. I'm new to the bucket seat world so give a newbie a break.

Originally Posted by special-K

...71/72 bucket seat backs are less tapered than 69/70s.

There's your answer. The other seats in the thread are 69/70.

Originally Posted by z10kl

OK, I been thinking about doing mine with buckets.
1. How do you tell the diff between utility buckets and regular?
2. Do you have to use the truck pass side brackets or will the flip forward one work?
3. If the flip ones work in a truck is it an advantage for any reason?
4. Hugger CST, what color SEM matches Sandlewood?

1. Utility buckets can have the cushions modified,but the original ones are flat surfaced. The back has a tube frame at the edge and all came with steel backs that actually wrap over the side a bit. They are noticeably wider,too.
Here's a pic:

2. You would need the parts from the Blazer floor that accept the seat.
3. I guess if you moved the gas tank it would allow easier access behind the seat. You would only have access from between the seats without. The passenger seat flips right up to the dash/windshield. On the driver side the steering wheel will interfere. If tank is left in the cab,I see no advantage at all.
4. I don't know,ask Hugger CST

[JWall]

[doubleb's69]

Love the red JWall!

[72chevynut]

I know this is an old thread, but while researching original bucket seats I noticed this one mentioned that a console would not fit between utility buckets (with steel back cover). In my 71 K5, it has the original utility buckets (recovered) and a added console. Seats are still mounted original to blazer and console fits nicely between. Seats and console all function properly. Hope this helps any utility seat owners wanting a console.