Sub frame motor mounts - The 1947 - Present Chevrolet & GMC Truck Message Board Network

jjjmm56 · 01-29-2009, 05:00 PM

Any one that has done a camaro sub frame swap , is there a right and left hand motor mount for a SB. My motor sits about 3\4" off. The drivers side is more foward . Any ideas?

jjjmm56 · 01-29-2009, 06:20 PM

This sub frame is grafted to a 56 frame

56chevy1300 · 01-29-2009, 06:41 PM

Most likely because the Camaro crossmember is not symmetrical.

my67chevytruck · 01-30-2009, 12:02 AM

have to agree. i have a camaro subframe, and my engine is sitting square...

Robertw · 02-03-2009, 12:08 PM

or the sub could have been in a collision some time

jjjmm56 · 02-03-2009, 06:03 PM

Found out everything is good, I didn't think about the pass side cyl head being 3/4" offset. I did then frame swap 20 yrs ago when there wasn't a lot of info on it. But measured everything and it's all good!

01-29-2009, 05:00 PM	#1
jjjmm56 Registered User Join Date: Jan 2009 Location: kissimmee Florida Posts: 494	Sub frame motor mounts Any one that has done a camaro sub frame swap , is there a right and left hand motor mount for a SB. My motor sits about 3\4" off. The drivers side is more foward . Any ideas?

01-29-2009, 06:20 PM	#2
jjjmm56 Registered User Join Date: Jan 2009 Location: kissimmee Florida Posts: 494	Re: Sub frame motor mounts This sub frame is grafted to a 56 frame

01-29-2009, 06:41 PM	#3
56chevy1300 Registered User Join Date: Dec 2006 Location: Edmonton, Alberta Posts: 522	Re: Sub frame motor mounts Most likely because the Camaro crossmember is not symmetrical.

01-30-2009, 12:02 AM	#4
my67chevytruck Under Construction Join Date: Oct 2007 Location: Midlothian,TX (DFW) Posts: 4,555	Re: Sub frame motor mounts have to agree. i have a camaro subframe, and my engine is sitting square... __________________ Heath subscribe to the board here: http://67-72chevytrucks.com/vboard/payments.php http://67-72chevytrucks.com/vboard/s...d.php?t=157669 FAQ how to's 1956 Chevy Apache 1967 C10 SWB FleetSide (under construction) 1969 K10 SWB FleetSide (Future Build) 1972 C10 SWB Stepside (Future Build) 56 chevy truck : http://www.cardomain.com/ride/2955823/1 67 truck build: http://www.67-72chevytrucks.com/vboard/showthread.php?t=281357/1 69 k10: http://67-72chevytrucks.com/vboard/s...d.php?t=389470

02-03-2009, 12:08 PM	#5
Robertw Registered User Join Date: Jun 2008 Location: muldrow ok Posts: 87	Re: Sub frame motor mounts or the sub could have been in a collision some time

02-03-2009, 06:03 PM	#6
jjjmm56 Registered User Join Date: Jan 2009 Location: kissimmee Florida Posts: 494	Re: Sub frame motor mounts Found out everything is good, I didn't think about the pass side cyl head being 3/4" offset. I did then frame swap 20 yrs ago when there wasn't a lot of info on it. But measured everything and it's all good!



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.