The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-14-2017, 02:53 PM   #1
59chevy310p
Registered User
 
Join Date: Oct 2015
Location: Monroe, wa
Posts: 43
1958 GMC 336 tranny match up

Long story short got a 1958 GMC with the factory Pontiac 336 and I'm gonna be converting it to 4x4 trying to figure what tranny will bolt up to it so I can run four wheel drive. Didn't know if a turbo 350 will bolt right up. Anyone have some advice?
59chevy310p is offline   Reply With Quote
Old 05-14-2017, 09:21 PM   #2
dwcsr
Hollister Road Co.
 
dwcsr's Avatar
 
Join Date: Apr 2005
Location: Houston
Posts: 6,134
Re: 1958 GMC 336 tranny match up

Quote:
Originally Posted by 59chevy310p View Post
Long story short got a 1958 GMC with the factory Pontiac 336 and I'm gonna be converting it to 4x4 trying to figure what tranny will bolt up to it so I can run four wheel drive. Didn't know if a turbo 350 will bolt right up. Anyone have some advice?
Different pattern you would need something like this

http://www.wilcap.com/pontiac.html
dwcsr is offline   Reply With Quote
Old 05-14-2017, 09:59 PM   #3
Port&PolishMan
Registered User
 
Port&PolishMan's Avatar
 
Join Date: Mar 2017
Location: Etowah, TN
Posts: 210
Re: 1958 GMC 336 tranny match up

This Site does the Trans Swaps & Many Transmission Adapter Plates ..

You have to Dig around , but it's all there ..

https://www.novak-adapt.com/catalog/...er-case-parts/
Port&PolishMan is offline   Reply With Quote
Old 05-14-2017, 10:08 PM   #4
1project2many
Registered User
 
Join Date: Mar 2012
Location: Lakes Region NH
Posts: 3,149
Re: 1958 GMC 336 tranny match up

The Wilcap parts look complete and reliable. The flywheel spacer is an important part of installing an adapter. Couldn't find anything on the Novak page.
1project2many is offline   Reply With Quote
Old 05-14-2017, 10:39 PM   #5
Port&PolishMan
Registered User
 
Port&PolishMan's Avatar
 
Join Date: Mar 2017
Location: Etowah, TN
Posts: 210
Re: 1958 GMC 336 tranny match up

[QUOTE=1project2many;7942793]The Wilcap parts look complete and reliable. The flywheel spacer is an important part of installing an adapter. Couldn't find anything on the Novak page.[/QUOTE

Depends on what Transfer Vase Your going to use ..
That have lots of Adapter Plates for that . .

https://www.novak-adapt.com/catalog/...o-transmission

Do You have the SM465 ?

After Cruising that Site - Their Engineering does look Better . . !

Last edited by Port&PolishMan; 05-14-2017 at 10:59 PM.
Port&PolishMan is offline   Reply With Quote
Old 05-15-2017, 12:16 AM   #6
59chevy310p
Registered User
 
Join Date: Oct 2015
Location: Monroe, wa
Posts: 43
Re: 1958 GMC 336 tranny match up

I have the stock 4 speed manual tranny in it right now. currently don't have any tranny or transfercase for the project just getting started and trying to figure out what I can use.
59chevy310p is offline   Reply With Quote
Old 05-15-2017, 09:00 AM   #7
1project2many
Registered User
 
Join Date: Mar 2012
Location: Lakes Region NH
Posts: 3,149
Re: 1958 GMC 336 tranny match up

If you're OK with keeping a 4 speed the M420 is a tough transmission. The original NAPCO conversion was an add-on kit and used a divorced transfer case. Divorced transfer cases were common on trucks in the '60s and '70s and one advantage to using this style case is that you don't have to change any of the original engine or transmission configuration.

A later SM465 may bolt to the original bell housing. It does in the Chevrolets but I'm not going to promise it will work in the GMC with the Poncho engine. If you can use an SM465 then you can use a later transmission/transfer case assembly.

Many later 4X4 trucks have a wider stance which comes with with wider axles and wider spring mounts. Finding axles that fit under a TF with no modification can be a challenge. IIRC the 72-ish Dodge 1/2 ton trucks are very close. They also happen to use a divorced transfer case, the NP205, which is very tough. International and Ford trucks from the early '70s also used a divorced case but the axles may require more work to install.
1project2many is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 12:54 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com