The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 05-10-2018, 06:46 PM   #1
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
What differential rear end do I have???

I was gonna replace the differential fluid in my new to me 1970 GMC LWB 1/2t. Don't see a drain plug or a fill plug (are they on the front of the differential?

Can we tell by outside pics what kind of gears etc I have?

My SPID is long gone (previous owner replaced the glovebox with chrome one). Original seat was replaced also so no paper/sheet in the back of the seat.
Attached Images
 
hotwls13 is offline   Reply With Quote
Old 05-10-2018, 07:09 PM   #2
Mike C
Registered User
 
Mike C's Avatar
 
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,709
Re: What differential rear end do I have???

12 bolt truck. No drain plug. Fill plug is on passengers side of case in front of axle tube.
__________________
44 Willys MB
52 M38A1
64 Corvette Coupe
68 Camaro 'vert LT1 & TH700
69 Z/28 355 12.6's @110
69 Chevy Short Step 4 1/2"/7" drop
72 Jimmy 4WD 4spd 4" & 35's
02 GMC 2500HD 4x4 Duramax
Mike C is offline   Reply With Quote
Old 05-10-2018, 07:12 PM   #3
Steeveedee
Who Changed This?
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,019
Re: What differential rear end do I have???

You have to take the cover off to drain the diff. You can inspect the gears while you are in there.
__________________
~Steven

'70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper

Simi Valley, CA
Steeveedee is offline   Reply With Quote
Old 05-10-2018, 07:34 PM   #4
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Thanks guys. That wa s the only pic I had of the truck. After I posted it I figured fill must be on front. So if I have to take the cover off I’m also gonna need a new seal right? Any recommendations as to brand etc? Or just whatever my autozone has??
hotwls13 is offline   Reply With Quote
Old 05-10-2018, 07:50 PM   #5
Ironangel
Senior Member
 
Ironangel's Avatar
 
Join Date: Feb 2010
Location: Falls City, Nebraska "100 Miles From Nowhere"
Posts: 2,219
Re: What differential rear end do I have???

Fel-Pro RDS 13391...Any GL-5 MP Gear Lube in the 80w/90 will work...
__________________
Michael of the clan Hill,
"Two Seventy Two's"
71 1-ton Dually 350 4-Speed
71 C/50 Grain Truck, 350 Split-Axle 4-Speed
02 3/4 ton Express
14 Indian Chief Vintage
1952 Ford 8N, "Only Ford Allowed On The Property"
"Be American, Buy American"
Ironangel is offline   Reply With Quote
Old 05-10-2018, 08:47 PM   #6
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Quote:
Originally Posted by Ironangel View Post
Fel-Pro RDS 13391...Any GL-5 MP Gear Lube in the 80w/90 will work...
Awesome thanks for the details!!
hotwls13 is offline   Reply With Quote
Old 05-10-2018, 10:15 PM   #7
Boog
laying low
 
Boog's Avatar
 
Join Date: Mar 2001
Location: Searcy, Ark. USA
Posts: 12,888
Re: What differential rear end do I have???

turn
Attached Images
 
__________________
Boog
69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver
primer is finer
91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said.

I stand for the flag and kneel at the cross
Boog is offline   Reply With Quote
Old 05-11-2018, 08:30 AM   #8
Mike C
Registered User
 
Mike C's Avatar
 
Join Date: Dec 1999
Location: Austin, TX, USA
Posts: 7,709
Re: What differential rear end do I have???

Once you get cover off you can get gear ratio from numbers stamped on OD of ring gear. You will also know if it has a limited slip and if so you will need to buy the friction modifier additive.
__________________
44 Willys MB
52 M38A1
64 Corvette Coupe
68 Camaro 'vert LT1 & TH700
69 Z/28 355 12.6's @110
69 Chevy Short Step 4 1/2"/7" drop
72 Jimmy 4WD 4spd 4" & 35's
02 GMC 2500HD 4x4 Duramax
Mike C is offline   Reply With Quote
Old 05-11-2018, 10:01 AM   #9
Knight72
Registered User
 
Join Date: Aug 2016
Location: Southside, Alabama
Posts: 173
Re: What differential rear end do I have???

Op, a factory Lsd will look like this.
Attached Images
 
__________________
72 C10 lwb fleetside aka Big Rhonda.

Still plugging away.

Build thread:
http://67-72chevytrucks.com/vboard/s...42#post8247142
Knight72 is offline   Reply With Quote
Old 05-11-2018, 11:08 AM   #10
Boog
laying low
 
Boog's Avatar
 
Join Date: Mar 2001
Location: Searcy, Ark. USA
Posts: 12,888
Re: What differential rear end do I have???

Turn
Attached Images
 
__________________
Boog
69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver
primer is finer
91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said.

I stand for the flag and kneel at the cross
Boog is offline   Reply With Quote
Old 05-11-2018, 11:16 AM   #11
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Thanks guys. I'm a total newb at all of this. All of these gears look like drilling equipment to me. Haha.

So, I have a 12 bolt and when I get the cover off, where specifically are the numbers I'm looking for??

Just want to be sure I get all the info I need while in there.

Also, I picked up gear oil (80-90w) and the fel-pro gasket last night. What' proper procedure for putting the new gasket back on?? Do I need sealant as well? If so what type?

Just don't want to make things worse by getting in there and screwing something up.

I plan to take a bunch of pics but don't want to go back in if I don't have to.
hotwls13 is offline   Reply With Quote
Old 05-11-2018, 11:24 AM   #12
Knight72
Registered User
 
Join Date: Aug 2016
Location: Southside, Alabama
Posts: 173
Re: What differential rear end do I have???

Numbers in the red block. I don't believe felpro gaskets require sealant.
Attached Images
 
__________________
72 C10 lwb fleetside aka Big Rhonda.

Still plugging away.

Build thread:
http://67-72chevytrucks.com/vboard/s...42#post8247142
Knight72 is offline   Reply With Quote
Old 05-11-2018, 12:09 PM   #13
69 MOD
Senior Member
 
69 MOD's Avatar
 
Join Date: May 2013
Location: Lino Lakes, MN
Posts: 362
Re: What differential rear end do I have???

I'm not advocating not pulling the cover but if you jack the rear end up, put it in neutral and make a mark on your driveshaft you can make a very close estimate on gear ratio.

In one full rotation of your rear tire the driveshaft mark will go past 0 point X amount of times (short of 3 turns 2:54, just over 3 turns would be 3:04, 3-3/4 would be 3:73 etc.)

Backyard trick I picked up when I was a kid...
MOD
__________________
Chad

'71 GMC 2500 Custom Ol Blue
'72 Custom Deluxe Highlander Stuffed Olive
'73 Trans Am
'13 Silverado 2500 Duramax Storm Trooper
69 MOD is offline   Reply With Quote
Old 05-11-2018, 12:29 PM   #14
Stocker
20' Daredevil (Ret)
 
Stocker's Avatar
 
Join Date: May 2003
Location: Jefferson State
Posts: 13,488
Re: What differential rear end do I have???

If you decide to use a gasket sealer (I always do, gives me peace of mind), get Permatex 81182 -- it's made specifically for use with gear oil.

__________________
- Mike -

1972 K20 LWB 350/350/205

RIP El Jay
Stocker is offline   Reply With Quote
Old 05-11-2018, 12:33 PM   #15
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Thanks again everyone for the tips. I usually drive new/newer vehicles, and usually have the maintenance done by a pro. So intentionally getting into stuff like this is not typical for me. haha

But, I want to know that the running gear is OK before I start driving it around and especially if I put my family in it. A good friend of mine who has been working on vehicles for over 50 years is my mentor and though he is kinda tired of working on them, he gives very good and important advice. He said "check and change the rear end oil" so that is getting done. Figure while I'm in there it's important to find out what I have.

Might be kind of a Duh question but, I'm guessing it's better to change/fill fluid while it's on level ground? Correct? But to see the side of the gear I may need to jack up the rear wheels to spin the gear??

I usually lift the rear with jack under the pumpkin. Should I put the rear on low jacks, pop cover off, drain, ID the gears, put cover back on, then drop wheels on the ground then add fluid?

Also, I've read where some people use a little RTV with the fel-pro gaskets?? Do or don't do that? And if I do, how long should I give the RTV to dry/set before filling with oil?

Lastly, what are the torque specs for the rear end bolts?
hotwls13 is offline   Reply With Quote
Old 05-14-2018, 12:19 PM   #16
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Some external pics, hoping to get into the differential tonight.
Attached Images
   
hotwls13 is offline   Reply With Quote
Old 05-14-2018, 12:43 PM   #17
custom10nut
Registered User
 
custom10nut's Avatar
 
Join Date: Apr 2015
Location: East Tn (In the heart of the Smoky Mtns)
Posts: 1,846
Re: What differential rear end do I have???

Chiming in. I did this with mine last year, because the gasket failed. A light coat of the permatex will prevent any weeping.
On a side note:
Does anyone know where to get an "S-clip" these days?
We used to get them when I was a kid (like 35 years ago)
The clip will "tighten up" a one wheeler to make a poor man's posi
custom10nut is offline   Reply With Quote
Old 05-14-2018, 02:43 PM   #18
BCOWANWHEELS
Registered User
 
Join Date: Nov 2006
Location: KINGSPORT,TN.
Posts: 3,035
Re: What differential rear end do I have???

forget gasket......... use permatex ultra black rtv. works a lot better as for diff lube use synthetic , you,ll never have to change it again ever. wash rear out with spray starting fluid.
__________________
I BELIEVE IN JOHN 3:16
BCOWANWHEELS is offline   Reply With Quote
Old 05-14-2018, 03:17 PM   #19
leddzepp
Moderator
 
leddzepp's Avatar
 
Join Date: May 2007
Location: Southern Cal
Posts: 19,972
Re: What differential rear end do I have???

Light coat of permatex on both sides of gasket. Let it tack over a bit, then install. Bolts do not need much torque at all, whatever service manual says. I’ve never had a leaking diff cover in my life doing it this way.
__________________
1972 C/10 Cheyenne Super SWB. Restored, loaded, slammed.

1968 C/10 50th Anniversary LWB. Unrestored, stock, daily driver/work truck.


RIP ElJay
RIP 67ChevyRedneck
RIP Grumpy Old Man
leddzepp is offline   Reply With Quote
Old 05-14-2018, 03:47 PM   #20
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Quote:
Originally Posted by leddzepp View Post
Light coat of permatex on both sides of gasket. Let it tack over a bit, then install. Bolts do not need much torque at all, whatever service manual says. I’ve never had a leaking diff cover in my life doing it this way.
Ok thanks. Don't have a service manual. Did look in the pdf version, couldnt find torque specs for rear end. Friend said not tight, one handed on ratchet close to head of ratchet (if that makes sense).
hotwls13 is offline   Reply With Quote
Old 05-14-2018, 05:37 PM   #21
Steeveedee
Who Changed This?
 
Steeveedee's Avatar
 
Join Date: Jan 2013
Location: Simi Valley, CA
Posts: 10,019
Re: What differential rear end do I have???

Bolt torque for the diff cover is specified on page 464. Dana 60 gets 35 Ft-Lbs.
__________________
~Steven

'70 Chevy 3/4T Longhorn CST 402/400/3.56 Custom Camper

Simi Valley, CA
Steeveedee is offline   Reply With Quote
Old 05-14-2018, 06:41 PM   #22
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Quote:
Originally Posted by Steeveedee View Post
Bolt torque for the diff cover is specified on page 464. Dana 60 gets 35 Ft-Lbs.
found it thanks. Page 646.

So I have a Dana 60??
hotwls13 is offline   Reply With Quote
Old 05-14-2018, 07:11 PM   #23
BCOWANWHEELS
Registered User
 
Join Date: Nov 2006
Location: KINGSPORT,TN.
Posts: 3,035
Re: What differential rear end do I have???

12 bolt gm
__________________
I BELIEVE IN JOHN 3:16
BCOWANWHEELS is offline   Reply With Quote
Old 05-14-2018, 11:42 PM   #24
Ironangel
Senior Member
 
Ironangel's Avatar
 
Join Date: Feb 2010
Location: Falls City, Nebraska "100 Miles From Nowhere"
Posts: 2,219
Re: What differential rear end do I have???

Quote:
Originally Posted by hotwls13 View Post
found it thanks. Page 646.

So I have a Dana 60??
No, you have a GM-12T (12-Bolt Truck) What manual are you guys getting page numbers from? My 72 Service Manual dont have page numbers...? 3/8-16 cover bolts get 35 ft lbs, 5/16-18 get 23 ft lbs, and the 1/4-20 cover bolts get 18 ft lbs. Your GM 12T cover bolts get 23 ft lbs. Make sure the cover mating surface is clean and flat, same for the carrier housing. Use a can or two of Brake Clean to spray the inside of the housing clean, dont forget the drip pan. Check your vent while your under there, a clogged vent will lead to seal leaks. Vents located on the top right of the diff housing. Make sure you place jack stands under the axle before you go to work under there. LeddZepp gave a good method for sealing the cover gasket. The Fel-Pro gasket # for the 12T is RDS 13391. "There is no reason not to use a gasket and several reasons why you should"
__________________
Michael of the clan Hill,
"Two Seventy Two's"
71 1-ton Dually 350 4-Speed
71 C/50 Grain Truck, 350 Split-Axle 4-Speed
02 3/4 ton Express
14 Indian Chief Vintage
1952 Ford 8N, "Only Ford Allowed On The Property"
"Be American, Buy American"

Last edited by Ironangel; 05-14-2018 at 11:52 PM.
Ironangel is offline   Reply With Quote
Old 05-15-2018, 12:55 AM   #25
hotwls13
Registered User
 
Join Date: Mar 2018
Location: Bakersfield, CA
Posts: 308
Re: What differential rear end do I have???

Here are the pics. I've got it all sealed back up, filling it back up tomorrow.
Attached Images
   
hotwls13 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:00 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com