|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
10-07-2016, 01:16 AM
|
#1 |
|
Registered User
Join Date: Apr 2009
Location: Murray,KY
Posts: 39
|
Help with Dana 44 front axle
Which direction does the chamfer face on the thrust washer that is on the stub shaft? I can't get the small snap ring on when I put my locking hub in. Wondering if the thrust washer may be my problem. Driver side went together with no problem.
|
|
|
|
10-07-2016, 01:49 PM
|
#2 |
|
Senior Member
 Join Date: Mar 2003
Location: Colfax-California
Posts: 8,382
|
Re: Help with Dana 44 front axle
It should face towards the u-joint
|
|
|
|
|
10-11-2016, 09:29 AM
|
#3 |
|
Registered User
Join Date: Apr 2000
Location: Chester County PA, USA
Posts: 1,228
|
Re: Help with Dana 44 front axle
You can reach in behind, and push out out the stub, while trying to put the snap ring on.
__________________
72 k/10 short wideside 72 k/5 Blazer 72 K/5 Blazer - obstacle course racer 72 custom/10 8' bed 70 K/5 Blazer 67 C-30 GMC Flat bed 86 GMC K2500 Plow Truck 85 GMC K3500 84 M1008 85 M1008 77 G30 Motor Home 72 Sears 12hp Tractor Glenmoore, Pennsylvania |
|
|
|
|
10-12-2016, 09:09 AM
|
#4 |
|
Special Order
  
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Re: Help with Dana 44 front axle
I've had the problem a few times and it was the bronze wheel bearing spacer placed in the wrong place. IIRC it was outside the outer bearing instead of inside the inner. #52
http://77cj.littlekeylime.com/Spicer...re_Dana44_.gif Been a while, but I think I remembered it right.
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
10-12-2016, 09:19 AM
|
#5 | |
|
Registered User
Join Date: Apr 2000
Location: Chester County PA, USA
Posts: 1,228
|
Re: Help with Dana 44 front axle
Quote:
51 is the thrust washer.
__________________
72 k/10 short wideside 72 k/5 Blazer 72 K/5 Blazer - obstacle course racer 72 custom/10 8' bed 70 K/5 Blazer 67 C-30 GMC Flat bed 86 GMC K2500 Plow Truck 85 GMC K3500 84 M1008 85 M1008 77 G30 Motor Home 72 Sears 12hp Tractor Glenmoore, Pennsylvania |
|
|
|
|
|
10-16-2016, 07:59 AM
|
#6 | |
|
Special Order
Join Date: Nov 2004
Location: Mt Airy, MD
Posts: 85,859
|
Re: Help with Dana 44 front axle
Quote:
__________________
"BUILDING A BETTER WAY TO SERVE THE USA"......67/72......"The New Breed" GMC '67 C1500 Wideside Super Custom SWB: 327/M22/3.42 posi.........."The '67" (project) GMC '72 K2500 Wideside Sierra Custom Camper: 350/TH350/4.10 Power-Lok..."The '72" (rolling) Tim "Don't call me a redneck. I'm a rough cut country gentleman" R.I.P. ~ East Side Low Life ~ El Jay ~ 72BLUZ ~ Fasteddie69 ~ Ron586 ~ 67ChevyRedneck ~ Grumpy Old Man ~ |
|
|
|
|
|
| Bookmarks |
| Thread Tools | |
| Display Modes | |
|
|
Linear Mode
