The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > All 4x4 Tech & Off Roading

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 04-07-2022, 12:50 AM   #1
A.Delaney
Registered User
 
A.Delaney's Avatar
 
Join Date: Aug 2013
Location: Streator IL
Posts: 63
Dana 44 6 lug to 8 lug conversion

Since I can’t find a Dana 60. Is it simple enough to convert my 44 to 8 lug or would it be better to look for a complete HD front end?
__________________
72 Chevy C20
86 Silverado Shortbed
A.Delaney is offline   Reply With Quote
Old 04-07-2022, 02:20 AM   #2
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,553
Re: Dana 44 6 lug to 8 lug conversion

D44 and corp10 are basically the same axle..
on a corp10 you have to change the complete outers..
The Corp10 1/2t & 3/4t are the same inside the Cs ,so all you gain is extra lugs..
The 3/4t axles are getting harder to find..
And unless you doing heavy offroad, a D60 is a big chunk of iron up front
Heres one of many articles on it
https://forums.off-road.com/threads/...-8-lug.105161/
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 04-07-2022, 02:19 PM   #3
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,343
Re: Dana 44 6 lug to 8 lug conversion

Depending on the year of your 44 it could be as simple as a backing plate and hub/rotor swap. You can even still use the 1/2 ton caliper over
kwmech is offline   Reply With Quote
Old 04-07-2022, 09:30 PM   #4
A.Delaney
Registered User
 
A.Delaney's Avatar
 
Join Date: Aug 2013
Location: Streator IL
Posts: 63
Re: Dana 44 6 lug to 8 lug conversion

The plan as of now is 8” lift with 38’s and a 496” bbc. Should be around 700hp. The chassis now has a D44/12 bolt combo. I have a 14 bolt full floater for the rear now. I can get by with the d44 in the front but I would like it to be at least 8 lug to match the rear. It might look goofy with 6 lug in the front and 8 in the back.
__________________
72 Chevy C20
86 Silverado Shortbed
A.Delaney is offline   Reply With Quote
Old 04-08-2022, 07:31 AM   #5
mongocanfly
Post Whore

 
mongocanfly's Avatar
 
Join Date: May 2015
Location: Alabama
Posts: 14,553
Re: Dana 44 6 lug to 8 lug conversion

Yep..sounds like you need a 60 up front
__________________
Mongo...aka Greg

RIP Dad
RIP Jesse

1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598
Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334
Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563
2023 Chevy Z71..daily driver
mongocanfly is offline   Reply With Quote
Old 04-08-2022, 09:28 AM   #6
57taskforce
All about them K’s
 
57taskforce's Avatar
 
Join Date: Jun 2014
Location: Farmington, New Mexico
Posts: 6,148
Re: Dana 44 6 lug to 8 lug conversion

If you are planning to use that HP with those tires off road in 4x4 you are going to want a front 60 for sure.
__________________
Tyler
'57 3100 http://67-72chevytrucks.com/vboard/s...d.php?t=813888
'72 K20 Cheyenne http://67-72chevytrucks.com/vboard/s...d.php?t=662879
‘69 K10 SWB http://67-72chevytrucks.com/vboard/s...d.php?t=805206
'98 Silverado LT K2500HD ECLB Vortec 454/4l80E: 6" lift 315/75/16's
‘87 IROC-Z all original 50K mile survivor TPI 305 IROC Blue
‘10 Camaro 2SS/RS Aqua Blue Metallic #93 -version 2.0
57taskforce is online now   Reply With Quote
Old 04-09-2022, 10:38 AM   #7
Zoomad75
K5Camper
 
Zoomad75's Avatar
 
Join Date: Mar 2004
Location: Pueblo, CO
Posts: 1,513
Re: Dana 44 6 lug to 8 lug conversion

I’ve done a lot of wheeling with a d44 up front. It really depends on what you are doing and if you are going to run a limited slip or locker in it.

38” tires are pushing it too.

I beat the snot out of the 6 lug 44 in my ‘75 K5 but it had a wheezy 350, but it was with a manual trans. So there was a lot of shock load hammering on and off the throttle. It was open and I can say that’s probably what kept it alive.

Fast forward to my ‘91. 8 lug 44 with a Detroit Tru-trac helical limited slip. It stated out with a stock 5.3L ls swap and a 700r4. Managed to break two right side shafts and a single left side shaft. The shafts broke on three different trips to Utah over three different years. All were not getting hammered on either. Got stuck or hung up on something and was literally just going into reverse when they broke. Each time.

I’ve had the 8.1L in with a 5 speed for over a year now. Same 44 up front. A handful of off road trips under its belt, including crawling in Moab. No break. But the manual allows a different amount of finesse that I didn’t have with the auto.

I’m really cautious to not give it the beans with the wheels cranked to one side or the other. I carry spares too.

It comes back to what the plan is and how you plan on using it. Chrome-moly shafts for the 44 are an option to add strength where it’s needed too. But they don’t expect them to survive long term with 37” tires or larger. The will warranty them if you are running 35’s or smaller.
Posted via Mobile Device
Zoomad75 is offline   Reply With Quote
Old 07-17-2022, 09:31 PM   #8
A.Delaney
Registered User
 
A.Delaney's Avatar
 
Join Date: Aug 2013
Location: Streator IL
Posts: 63
Re: Dana 44 6 lug to 8 lug conversion

Well I picked up a Dana 60 today. Finally found one that wasn’t a ridiculous price. I am thinking about running a Detroit Truetrac locker in the rear. I’m wondering how that would be on the street. Clunky going around corners? The rear is a 14 bolt FF.
__________________
72 Chevy C20
86 Silverado Shortbed
A.Delaney is offline   Reply With Quote
Old 07-23-2022, 02:45 AM   #9
Richard
Senior Member
 
Join Date: Dec 1999
Location: Southern California
Posts: 2,647
Re: Dana 44 6 lug to 8 lug conversion

Quote:
Originally Posted by A.Delaney View Post
Well I picked up a Dana 60 today. Finally found one that wasn’t a ridiculous price. I am thinking about running a Detroit Truetrac locker in the rear. I’m wondering how that would be on the street. Clunky going around corners? The rear is a 14 bolt FF.
That is a gear type diff, no clunking. Excellent on the street. Should be real smooth. Just be aware that those limited slips turn into an open diff if you lift a wheel or one wheel looses complete traction. A little brake can help the situation.
__________________
Richard
1972 K10 Custom Deluxe SWB Fleetside
My build https://67-72chevytrucks.com/vboard/...d.php?t=800746
Richard is offline   Reply With Quote
Old 07-25-2022, 10:43 PM   #10
A.Delaney
Registered User
 
A.Delaney's Avatar
 
Join Date: Aug 2013
Location: Streator IL
Posts: 63
Re: Dana 44 6 lug to 8 lug conversion

Okay great thanks.
__________________
72 Chevy C20
86 Silverado Shortbed
A.Delaney is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:04 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com