The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1967 - 1972 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-28-2017, 07:16 PM   #1
willy12844
Registered User
 
Join Date: Jul 2015
Location: Gilberts, illinois
Posts: 102
Testing radio

I've had a old radio given to me along with the speaker. It has "GM" on the front and is AM only. I'd like to test it before I put it into my 72 C-10. How is the best way to test a radio out of the vehicle. The dial along with the push buttons work.
Thanks,
Bill
__________________
The pessimist is one who feels bad when he feels good for,
fear he'll feel worse when he feels better
willy12844 is offline   Reply With Quote
Old 10-28-2017, 09:20 PM   #2
franken
Registered User
 
Join Date: Jun 2013
Location: Somewhere
Posts: 3,052
Re: Testing radio

I'm looking at a truck AM radio and it says, don't operate w/o an 8-10 Ohm speaker. Electrical connections appear to be 12V, ground and speaker.
franken is offline   Reply With Quote
Old 10-28-2017, 09:55 PM   #3
bill3rail
Registered User
 
bill3rail's Avatar
 
Join Date: Jul 2013
Location: LI, NY 11801
Posts: 1,140
Re: Testing radio

I have two spare radios with three sets of knobs and have not tested them yet.
I would guess power it up, plug in antenna and add speaker should do it...

Bill
__________________
1970 C10 8' Fleetside, L6 250, 3 on the Tree.
The most basic of pickup trucks!
bill3rail is offline   Reply With Quote
Old 10-28-2017, 09:57 PM   #4
bill3rail
Registered User
 
bill3rail's Avatar
 
Join Date: Jul 2013
Location: LI, NY 11801
Posts: 1,140
Re: Testing radio

Quote:
Originally Posted by franken View Post
I'm looking at a truck AM radio and it says, don't operate w/o an 8-10 Ohm speaker. Electrical connections appear to be 12V, ground and speaker.
Is the speaker Ohm rating that important? Maybe long term but for testing I think anything should be fine.
__________________
1970 C10 8' Fleetside, L6 250, 3 on the Tree.
The most basic of pickup trucks!
bill3rail is offline   Reply With Quote
Old 10-28-2017, 10:12 PM   #5
BLT gmc
Registered User
 
Join Date: Feb 2014
Location: West Iowa
Posts: 1,109
Re: Testing radio

Absolutely not. Don't turn on or power up radio without proper ohm speaker. The output coil in the radio will fry within a 1/2 sec.
Posted via Mobile Device
BLT gmc is offline   Reply With Quote
Old 10-29-2017, 11:02 AM   #6
willy12844
Registered User
 
Join Date: Jul 2015
Location: Gilberts, illinois
Posts: 102
Re: Testing radio

I have the speaker that came out of the Blazer the radio came out of, they go together.
Thanks for all the help folks.
__________________
The pessimist is one who feels bad when he feels good for,
fear he'll feel worse when he feels better
willy12844 is offline   Reply With Quote
Old 10-29-2017, 04:28 PM   #7
bill3rail
Registered User
 
bill3rail's Avatar
 
Join Date: Jul 2013
Location: LI, NY 11801
Posts: 1,140
Re: Testing radio

Quote:
Originally Posted by BLT gmc View Post
Absolutely not. Don't turn on or power up radio without proper ohm speaker. The output coil in the radio will fry within a 1/2 sec.
Posted via Mobile Device
If this is true, I have blown many radios in my life! Crap!!
__________________
1970 C10 8' Fleetside, L6 250, 3 on the Tree.
The most basic of pickup trucks!
bill3rail is offline   Reply With Quote
Old 10-29-2017, 04:31 PM   #8
ray_mcavoy
Registered User
 
Join Date: Nov 2009
Location: Sherman, ME
Posts: 2,350
Re: Testing radio

Start by checking the speaker with an ohmmeter. The DC resistance will be a little bit less than the nominal 8 to 10Ω impedance so don't worry if you don't get that exact reading on your meter. You just want to make sure it isn't short circuited (zero Ohms) and that it is not open circuited (infinite reading, which would be the same as operating the radio without a speaker).

If your speaker checks out okay and still has the factory 3-terminal plug, simply plug that into the radio (it should be keyed so it will only fit one way). The empty/unused terminal in that plug is the +12V feed to the radio. Connect that through a fuse to the positive side of a 12V DC power supply or battery. Then connect the negative side of the power supply or battery to the metal case of the radio. Finally, plug in an antenna, turn the radio on, and with a little luck it should come to life. It's not uncommon for the volume & tone controls on these old radios to be a bit dusty & dirty so expect some popping & crackling noises as you adjust those controls. Spraying them with a little bit of cleaner (I use Caig DeoxIT F5) usually cleans them up and gets rid of the noise.
ray_mcavoy is offline   Reply With Quote
Old 10-29-2017, 04:44 PM   #9
Killer Bee
Registered User
 
Killer Bee's Avatar
 
Join Date: Jan 2016
Location: Barber City, CA
Posts: 4,717
Re: Testing radio

Quote:
Originally Posted by BLT gmc View Post
Absolutely not. Don't turn on or power up radio without proper ohm speaker. The output coil in the radio will fry within a 1/2 sec.
Posted via Mobile Device
true story.. I received the same warning from the owner here [forget who is who]

http://www.turnswitch.com/speakers.htm
vintage speakers Greg / Dan 877-780-2861

although many of us may have been lucky, no need to press our luck if we know better now, right?

turn switch does sell the correct speakers btw and they can answer many of your old radio questions..

good luck!
Killer Bee is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:50 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com