The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Electrical

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 09-28-2018, 10:45 PM   #1
MikeB
Senior Member
 
MikeB's Avatar
 
Join Date: Jul 2000
Location: North Texas
Posts: 3,378
Fuse panel & wiring harness kits

Due to a water leak over much of its life, my 82 C10's fuse panel has lots of corroded, and even rusty fuse sockets -- not from getting wet, but from just sitting above the moisture on the floor. Seems like every few months I have to pull a fuse and use a burnishing tool to clean up the fuse panel contacts. But that's usually a temporary fix. Also, with a battery voltage of 12.6 volts, the dash lamps, headlamps, wipers, etc. see only around 11 volts, so I've got a voltage drop somewhere. And that's with two 10 gauge wires feeding the fuse panel.

Bottom line is I need to replace the fuse panel, and might as well get rid of the bulkhead connectors as a potential problem source, which means getting an entire kit including harnesses. I've installed an American Autowire Classic Update harness on a 66 truck, and really liked it, but for a square body, they cost $845. Also looking at a $465 Ron Francis XP-751 kit, but the panel is 7-1/2"wide, which makes it a really tight fit between kick panel and steering column. BTW, on another car I finished the install of a Ron Francis kit where the wires are terminated at the fuse panel, and I think that makes for a neater setup under the dash. Also, the kit uses 8 gauge wires for the panel feed and charging circuit, and virtually all the wires are larger than stock. Too bad the XP-751 Express fuse panel is so wide.

Pretty much ruled out Painless because they actually use smaller gauge wire than my factory wiring for panel feed and ignition! (Panel feed is two 10 gauge wires, but they crimp them to two 12 gauge wires 6" before the panel. Huh?)

What have you guys used, and are you happy with it?
__________________
Mike
1969 C10 LWB -- owned for 34 years. 350/TH350, 3.08 posi, 1st Gen Vintage Air, AAW wiring harness, 5-lug conversion, 1985 spindles and brakes.
1982 C10 SWB -- sold
1981 C10 Silverado LWB -- sold, but wish I still had it!
1969 C10 (not the current one) that I bought in the early 1980s. Paid $1200; sold for $1500 a few years later. Just a hint at the appreciation that was coming.
Retired as a factory automation products salesman.
Worked part-time over the years for an engine builder and a classic car repair shop.
Member here for 23 years! This is the very first car/truck Internet forum I joined. I still used a dial-up modem back then!

Last edited by MikeB; 09-29-2018 at 08:54 PM.
MikeB is offline   Reply With Quote
Old 10-01-2018, 04:29 PM   #2
SunSoaked
Registered User
 
SunSoaked's Avatar
 
Join Date: Dec 2011
Location: Yuma Arizona
Posts: 1,524
Re: Fuse panel & wiring harness kits

You sure the smaller sections aren't fusible links?
SunSoaked is offline   Reply With Quote
Old 10-01-2018, 05:23 PM   #3
MikeB
Senior Member
 
MikeB's Avatar
 
Join Date: Jul 2000
Location: North Texas
Posts: 3,378
Re: Fuse panel & wiring harness kits

Yes, the kit uses a maxi-fuse instead. And the transition is the last 6" or so before connecting the fuse panel B+ bus.
__________________
Mike
1969 C10 LWB -- owned for 34 years. 350/TH350, 3.08 posi, 1st Gen Vintage Air, AAW wiring harness, 5-lug conversion, 1985 spindles and brakes.
1982 C10 SWB -- sold
1981 C10 Silverado LWB -- sold, but wish I still had it!
1969 C10 (not the current one) that I bought in the early 1980s. Paid $1200; sold for $1500 a few years later. Just a hint at the appreciation that was coming.
Retired as a factory automation products salesman.
Worked part-time over the years for an engine builder and a classic car repair shop.
Member here for 23 years! This is the very first car/truck Internet forum I joined. I still used a dial-up modem back then!
MikeB is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 10:34 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com