|
Register or Log In To remove these advertisements. |
|
|
|
|||||||
 |
|
|
Thread Tools | Display Modes |
06-16-2017, 05:05 PM
|
#1 |
|
Registered User
Join Date: Aug 2007
Location: Orange City, Florida
Posts: 76
|
Door glass channel install help
Just bought a 72 Chevy truck (common theme around here it appears). Both window regulators were/are bad so I've ordered replacements. Anyways, the metal channel that goes on the bottom of the door glass has fallen off. I bought the flat rubber inserts that go in the channel and around the bottom of the glass (to eliminate vibration I presume). I don't know what kind of adhesive I need to be using to glue the glass back into the channel. Any help would be appreciated. thanks
Scott |
|
|
|
06-16-2017, 07:44 PM
|
#2 |
|
Registered User
 
Join Date: Oct 2011
Location: jackson michigan
Posts: 755
|
Re: Door glass channel install help
I used black silicone.
|
|
|
|
|
06-16-2017, 07:53 PM
|
#3 |
|
Senior Member
Join Date: Dec 2013
Location: Gods country East,Tn
Posts: 8,545
|
Re: Door glass channel install help
Silicone doesn't last . toss the rubber inserts and use windshield sealant urethane sealer .do it once and be done with it .
|
|
|
|
|
06-18-2017, 09:36 PM
|
#4 |
|
Senior Member
Join Date: Feb 2002
Location: Tucson, AZ USA
Posts: 7,047
|
Re: Door glass channel install help
If it's the thin rubber sheeting that you wedge the bottom of the door glass into, then the 1968 Chassis Service manual recommended painting it with clean 30 weight engine oil. The oil would breakdown the rubber into an adhesive, and not rattle.
I couldn't find the archaic rubber sheet stuff, so I used some super adhesive a glass shop sold me, and now I can't get that window loose.
__________________
Every 25 years I like to rebuild that 292, whether it needs it or not. |
|
|
|
|
06-18-2017, 11:31 PM
|
#5 |
|
Registered User
Join Date: Feb 2004
Location: brownfield texas (west texas)
Posts: 1,936
|
Re: Door glass channel install help
You dont glue them in you are supposed to use window seam tape. If you heat it and tap it on it will stay very good. You can get a roll of it on ebay about 15 bucks. Measure the gap. Subtract the width of glass and devide by two for correct thickness. Get it slightly thick and the heat and rubber mallet will make a snug fit. Dont use oil even though thats what they used to do.
__________________
The Ghost 67 short wide full custom. 550 hp LSX, 4l80E, narrowed 9". Body dropped w/air ride! ........................ ___ .........________//__{\_____ ,,,,,,,/__(⊙)___//___/__(O)_/ @disciple2.rc 💪instagram💪 LED TAILS Last edited by Robznob11; 06-19-2017 at 08:56 AM. |
|
|
|
|
06-19-2017, 08:09 AM
|
#6 |
|
Senior Member
Join Date: Feb 2002
Location: Tucson, AZ USA
Posts: 7,047
|
Re: Door glass channel install help
Well I listened to the wrong guys 11 years ago. Now I may have to cut out the stuck window regulator with a cutting wheel. The regulator is stuck down, or about 1'' up. Won't go up. Won't go down. Gear stripped. Has to go all the way up to disassemble IIRC. Anyway I'm stuck til the new regulator gets in from GMC Paul.
Be some fun getting that window glass out. Sorry for the hijack.
__________________
Every 25 years I like to rebuild that 292, whether it needs it or not. |
|
|
|
|
06-19-2017, 09:03 AM
|
#7 |
|
Registered User
Join Date: Feb 2004
Location: brownfield texas (west texas)
Posts: 1,936
|
Re: Door glass channel install help
Here you go.....its called glass setting tape! This is what I used! I dont remember the thickness i used but it worked great for the side and re setting the vent glass. Also there are some great videos on youtube on it. Look at this on eBay
Look at this on eBay http://www.ebay.com/itm/351852977047
__________________
The Ghost 67 short wide full custom. 550 hp LSX, 4l80E, narrowed 9". Body dropped w/air ride! ........................ ___ .........________//__{\_____ ,,,,,,,/__(⊙)___//___/__(O)_/ @disciple2.rc 💪instagram💪 LED TAILS |
|
|
|
|
| Bookmarks |
|
|
Linear Mode
