The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1988 - 1998 GMT400 Chevy & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 10-27-2018, 05:28 PM   #1
crsgmc
Registered User
 
Join Date: Apr 2018
Location: Denver, CO
Posts: 19
Clutch Fluid

I have looked around a bit and have not found any answers. I have a 1996 GMC K1500 five speed manual transmission. The clutch fluid is really bad, like it is the original fluid when the truck was built. The transmission is a Getrag, probably the one the truck came with. It has an internal slave. My question is how do I drain / replace the fluid. Gravity bleed would probably work fine. There are two things sticking out of the slave with access holes in the transmission. Is one of those to drain the fluid, and if so which one? I just finished replacing the engine, clutch, and flywheel and I should have done it then. I didn't know it was this bad until the engine was in. If I had to do it again I would have also replaced the internal slave as well. Thanks for any assistance you can provide.
crsgmc is offline   Reply With Quote
Old 10-27-2018, 05:50 PM   #2
95 S_Trucker
Senior Member
 
95 S_Trucker's Avatar
 
Join Date: Oct 2009
Location: Lancaster, PA
Posts: 1,982
Re: Clutch Fluid

You have a NV3500 transmission.

Did you bleed the clutch when you replaced it? Your clutch kit should have came with a new hydraulic release bearing(slave cylinder).

They can be a real pain to bleed. You’d have to bleed it to change all of the fluid.
__________________
-99 K2500 LS CCSB 7.4
-11 GMC 2500HD SLE CCSB 6.0
-96 C3500 HD 7.4 NV4500 Rollback
-85 K10 5.7 700r4
-78 K10 5.7 4 Speed
-90 ZR1 5.7 6 Speed
-62 Lincoln Sedan 430 Auto
-61 Lincoln Convertable 430 Auto


85 Project: http://67-72chevytrucks.com/vboard/s...d.php?t=368864

78 Big10 Project: http://67-72chevytrucks.com/vboard/s...d.php?t=383629

96 Project: http://67-72chevytrucks.com/vboard/s...d.php?t=614515
95 S_Trucker is offline   Reply With Quote
Old 10-27-2018, 11:42 PM   #3
Mr_Rich
Registered User
 
Mr_Rich's Avatar
 
Join Date: May 2006
Location: Santa Maria, Calif.
Posts: 517
Re: Clutch Fluid

I would strongly recommend installing a remote bleeder from Speedway Motors or another vendor. The stock configuration is so difficult to bleed especially in a car like my '98 Firebird. When I replaced the engine and trans I installed a 3' remote bleeder in that car. Made a big difference in ease of maintenance.
Gravity bleed is a bad idea. It will drain out so quickly all you'll have is air in the system and then it's really a PITA.
__________________
1989 K1500 Chev. EC
Original owner; some of the aftermarket parts I've installed are Borla headers, Hypertech chip, Edelbrock water pump, and a Stillen rear disc brake conversion kit.
2009 Hummer H3T 3.7L 5M.
1997 K2500 Chev. EC 7.4L/ 4L80E
Mr_Rich is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:54 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com