The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Info Center > FAQ Truck Tech > 67-72

Web 67-72chevytrucks.com


Closed Thread
 
Thread Tools Display Modes
Old 03-02-2006, 05:42 PM   #1
Zumo
Hot Rods For Life
 
Zumo's Avatar
 
Join Date: Sep 2001
Location: Waxahachie, TX
Posts: 3,305
Tips for spring removal

Getting ready to remove my springs this weekend to cut them. Anyone have any comments.
__________________
1968 C10 LWB ****SOLD***
Andy
Viva Los Bicicletas!
Los Muertos Custom Bicycles

Last edited by Zumo; 04-09-2006 at 11:07 AM.
Zumo is offline  
Old 03-02-2006, 05:51 PM   #2
70c10
67-72 Addict!
 
70c10's Avatar
 
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,857
Re: Any tips for spring removal?

I cut 1.25 coils and got about 2 3/4" drop. After you cut the first coil use it as a template with a sharpie on the other one to be exact for the cut.
__________________
Jim

1970 C/10 Fleetside w/Ghost Flames
Lowered 4.5" front and 4" rear (Raked)
355/350 Turbo w/shift kit
10" Redneck Performance Verter w/2500 stall
Hooker Super Comps part#2808-1
Performer RPM Air-Gap
12 Bolt w/3:73 gears- Eaton Posi
Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads
70c10 is offline  
Old 03-02-2006, 05:53 PM   #3
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
Re: Any tips for spring removal?

no need for a compressor.
Support the truck by the frame
place floor jack under lower a arm and lightly lift... just enough to place a small load on the spring.
Disconnect lower ball joint
slowly lower jack. The spring will simply fall out. It will not be under pressure.
Longhorn Man is offline  
Old 03-02-2006, 05:56 PM   #4
70c10
67-72 Addict!
 
70c10's Avatar
 
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,857
Re: Any tips for spring removal?

LonghornMan is correct. Be careful when lowering the jack that you don't pull on the brake line too hard.
__________________
Jim

1970 C/10 Fleetside w/Ghost Flames
Lowered 4.5" front and 4" rear (Raked)
355/350 Turbo w/shift kit
10" Redneck Performance Verter w/2500 stall
Hooker Super Comps part#2808-1
Performer RPM Air-Gap
12 Bolt w/3:73 gears- Eaton Posi
Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads
70c10 is offline  
Old 03-02-2006, 06:09 PM   #5
Zumo
Hot Rods For Life
 
Zumo's Avatar
 
Join Date: Sep 2001
Location: Waxahachie, TX
Posts: 3,305
Re: Any tips for spring removal?

Sweet
__________________
1968 C10 LWB ****SOLD***
Andy
Viva Los Bicicletas!
Los Muertos Custom Bicycles
Zumo is offline  
Old 03-02-2006, 07:50 PM   #6
hotrodhomi
Registered User
 
hotrodhomi's Avatar
 
Join Date: Apr 2004
Location: Sacramento
Posts: 3,737
Re: Any tips for spring removal?

Why don't you buy new springs. They are cheap. I've had both and I would not recomend cut springs.
__________________
'72 2wd blazer, bagged w/ watts link & EDC
'72 C10 "Lowered Farm Truck" STOLEN 5-18-11
'66 impala ht
hotrodhomi is offline  
Old 03-02-2006, 08:48 PM   #7
glberen
Registered User
 
Join Date: Oct 2005
Location: Denton, Tx
Posts: 7
Re: Any tips for spring removal?

what do you cut the springs with?
glberen is offline  
Old 03-02-2006, 10:50 PM   #8
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
Re: Any tips for spring removal?

One man's budget part... is another man's truck budget. Not everyone has 200 bucks to throw at the springs, and many wouldn't call them cheap.


Quote:
Originally Posted by hotrodhomi
Why don't you buy new springs. They are cheap. I've had both and I would not recomend cut springs.
Longhorn Man is offline  
Old 03-02-2006, 08:49 PM   #9
70c10
67-72 Addict!
 
70c10's Avatar
 
Join Date: Feb 2002
Location: The TAX State!
Posts: 7,857
Re: Any tips for spring removal?

A 4" fiber disc.
__________________
Jim

1970 C/10 Fleetside w/Ghost Flames
Lowered 4.5" front and 4" rear (Raked)
355/350 Turbo w/shift kit
10" Redneck Performance Verter w/2500 stall
Hooker Super Comps part#2808-1
Performer RPM Air-Gap
12 Bolt w/3:73 gears- Eaton Posi
Comp Cams XE262 with 1.6 Crane Energizers, Road Demon 625 and Brodix IK 180 heads
70c10 is offline  
Old 03-02-2006, 08:56 PM   #10
Tx Firefighter
Watch out for your cornhole !
 
Tx Firefighter's Avatar
 
Join Date: Jun 2003
Location: Azle, Texas
Posts: 14,162
Re: Any tips for spring removal?

I'm opposite of hotrodhomi, I've had springs from Belltech, Eibach, Ground Force, and Early Classic. After all that, I've always been just as happy with cutting stock springs. One coil gets 3 inch drop without riding any worse than custom wound lowering springs.

Zumo, there are several ways to separate the lower ball joint. Some ways tend to damage the boot, some don't. I do the "loosen the nut way off and smack the spindle hard with a hammer method". It's never failed to work and doesn't damage the grease boot or anything else like a pickle fork will.
__________________
I'm on the Instagram- @Gearhead_Kevin
Tx Firefighter is offline  
Old 03-03-2006, 10:15 AM   #11
Joe67
67 is sold
 
Join Date: Apr 2001
Location: Troy, Michigan
Posts: 6,738
Re: Any tips for spring removal?

I guess I'll be the one who recommends using a spring compressor on the front springs.
I know quite a few people don't, but if you are not careful, removing them without one can cause serious injury...
__________________
Joe - Formerly 67c10step
-------------------------------
1967 Chevy Stepside - ECE 4/6, fuelcell, 5lug - SOLD

gr8lakes - My ebay auctions

Click here to order forum apparel :: Click here to become a subscribing member
Joe67 is offline  
Old 03-03-2006, 10:34 AM   #12
sneakysnake
It's a catastrophic success.
 
sneakysnake's Avatar
 
Join Date: Jan 2003
Location: Oklahoma
Posts: 2,077
Re: Any tips for spring removal?

If you dont want to risk damaging you ball joints, you can remove the two U bolts that hold the lower control arm to the cross member.Just make sure you put the jack on the cross bar or on a solid place on the lower arm because there will be more flexibility with it only being held by the lower ball joint.
sneakysnake is offline  
Old 03-03-2006, 12:25 PM   #13
LONGHAIR
just can't cover up my redneck
 
Join Date: May 2004
Location: Columbus OH
Posts: 11,414
Re: Any tips for spring removal?

I am totally with TxFirefighter on this one, the hammer method works very well. Just remember to leave the nut on, loosened by several threads. If you totally remove the nut the spindle/upper a-arm assembly can jump off of the ball-joint stud. This can result in damage to the boot too.

Of course every TV show that I have ever seen uses the pickle fork method, either with a hammer or air-chisel. This is fine if you are replacing the ball-joint.....but not for general dis-assembly and re-assembly of the original parts. This method may also be perfered in the case of custom painted or plated/powder-coated parts.......I think you can still buy the grease boots seperate from the ball-joints, though it has been many years since I tried.

There should not be any tension on the spring when you lower the a-arm, it should drop far enough for the spring to just fall/roll out........be prepared and watch you feet. Newer trucks (or those with new/tight bushings) may require you to pry down a bit to get the spring to drop out....S-10s usually require this too.

The new (shortened) springs got back in just as easily. Just set them in place in the lower pocket and raise the jack. As the spring contacts the upper pocket give it a tug/jiggle to be sure that it seats properly and continue to raise it up to meet the spindle. If it is not centered you will hear/feel a nasty snap when it does pop in under tension.

After you are done installing the spring it is a good idea to make sure that there is some tension on the spring when the suspension is at full droop. (resting on the bump-stop) Execssively shortened springs will be loose especially if the bump-stop is worn or missing.
LONGHAIR is offline  
Old 04-08-2006, 11:29 PM   #14
Zumo
Hot Rods For Life
 
Zumo's Avatar
 
Join Date: Sep 2001
Location: Waxahachie, TX
Posts: 3,305
Re: Any tips for spring removal?

where on the spindle do I hit? Won't I damage the threads?
__________________
1968 C10 LWB ****SOLD***
Andy
Viva Los Bicicletas!
Los Muertos Custom Bicycles
Zumo is offline  
Old 04-09-2006, 12:23 AM   #15
glock35ipsc
Next project: 1970 K10
 
glock35ipsc's Avatar
 
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
Re: Any tips for spring removal?

Quote:
Originally Posted by Zumo
where on the spindle do I hit? Won't I damage the threads?
Be sure you hit the spindle, not the ball joint stem!!!!

It may be easier if you have both wheels off the ground, then you can turn the wheels completely to one side to get a bigger area to swing at. Hit the spindle right where the ball joint stem goes through it. Thats another good reason for leaving the nut on, just in case the hammer glances off of the spindle and hits it, it will protect the threads.

Get a BFG, not a little wimpy ball peen. Should only take a good smack or two.

BTW, I used to work in alignment shops when I was wrenching, and never used a compressor or anything else when removing coils. Struts are a different story, but just lower the arm slowly and nothing will happen.
__________________
Bob

1970 Chevy K10 LWB "Goldie" 350/TH350 next project!!
1981 Chevy C10 LWB 355/TH350 - My son's truck

LS SWAP FORUM! Tons of LS swap info here!
PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET!
CLICK HERE FOR THE FAQ INDEX by KRUE

Last edited by glock35ipsc; 04-09-2006 at 12:25 AM.
glock35ipsc is offline  
Old 04-09-2006, 01:06 AM   #16
Zumo
Hot Rods For Life
 
Zumo's Avatar
 
Join Date: Sep 2001
Location: Waxahachie, TX
Posts: 3,305
Re: Any tips for spring removal?

SHould I disconnect the shock and sway bar from the lower spindle as well?
__________________
1968 C10 LWB ****SOLD***
Andy
Viva Los Bicicletas!
Los Muertos Custom Bicycles
Zumo is offline  
Old 04-09-2006, 02:01 AM   #17
glock35ipsc
Next project: 1970 K10
 
glock35ipsc's Avatar
 
Join Date: Feb 2004
Location: Fort Collins, Colo 80524
Posts: 6,685
Re: Any tips for spring removal?

Yes.
__________________
Bob

1970 Chevy K10 LWB "Goldie" 350/TH350 next project!!
1981 Chevy C10 LWB 355/TH350 - My son's truck

LS SWAP FORUM! Tons of LS swap info here!
PLEASE CLICK HERE TO SUPPORT THE GREATEST BOARD ON THE NET!
CLICK HERE FOR THE FAQ INDEX by KRUE
glock35ipsc is offline  
Old 04-09-2006, 09:31 AM   #18
Zumo
Hot Rods For Life
 
Zumo's Avatar
 
Join Date: Sep 2001
Location: Waxahachie, TX
Posts: 3,305
Re: Any tips for spring removal?

Cool.
__________________
1968 C10 LWB ****SOLD***
Andy
Viva Los Bicicletas!
Los Muertos Custom Bicycles
Zumo is offline  
Old 04-09-2006, 09:59 AM   #19
Rokcrln
Senior Member
 
Rokcrln's Avatar
 
Join Date: Jul 2005
Location: Winters Ca. 95694
Posts: 4,843
Re: Any tips for spring removal?

Yes the nut, Hammer, smack works great! I have been doing it this way for about 20yrs now with out fail or injury. Just did it yesterday on "Project Trazer" (blazer section) so we can detail the frame and install a "C" notch kit.Zumo do you plan on just cutting the front springs or also the rear? I think the rear will give you some trouble trying to clamp them back inplace. May be someone has a tip on this as well for you since we have only be talking acout the fronts so far! Good luck and do not for get the brfore and after pics!!!

Kevin
LFD Inc.
Rokcrln is offline  
Old 04-09-2006, 09:57 AM   #20
toddtheodd
The oddest Todd around
 
toddtheodd's Avatar
 
Join Date: May 2004
Location: Miami, Florida
Posts: 1,418
Re: Any tips for spring removal?

I've got a brass pin that I use when hammering on anything on my truck. It came out of a U-joint for a big rig. Since the brass is softer than steel, I don't have to worry about damaging the steel.
Ft. Worth Gear and Axle have them, and most likely other places that work on big drive shafts will have them as well.
Toad
__________________
"The greatest pleasure is to vanquish your enemies and chase them before you, to rob them of their wealth and see those dear to them bathed in tears, to ride their horses and clasp to your bosom their wives and daughters." Ghengis Khan

IIOY???
toddtheodd is offline  
Old 04-09-2006, 12:15 PM   #21
Longhorn Man
its all about the +6 inches
 
Longhorn Man's Avatar
 
Join Date: Jan 2001
Location: Hilliard Ohio
Posts: 2,693
Re: Any tips for spring removal?

you can't (at least shouldn't) cut the rear springs they are tapered or pigtailed.
Longhorn Man is offline  
Closed Thread

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 01:33 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com