The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > Info Center > FAQ Truck Tech > Interior > Audio

Web 67-72chevytrucks.com


Closed Thread
 
Thread Tools Display Modes
Old 01-21-2012, 03:51 AM   #1
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Adding an AM/FM Decal

To read the original thread and discussion on this topic go here- LINK

I recently acquired an early model van AM/FM radio. It has the Delco inscribed on the lens, which made me think it was an original truck radio. I later found out that it wasn't. The letting on the dial drum was white and a different font. I purchased some reproduction truck AM/FM drum decals to install. However, I could not find any write-up for installing any. So, being the do-it-your-selfer, I decided to do my own write-up.

So, here it goes...


1. Remove the 5 sheet metal screws on the top of the radio.
Attached Images
  
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal

Last edited by augie; 02-18-2012 at 08:29 PM.
70LonghornCST is offline  
Old 01-21-2012, 03:52 AM   #2
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

2. Remove the top cover. Be careful not too pull to hard so you don't damage the radio light connection at the circuit board.
Attached Images
   
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 03:56 AM   #3
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

3. Remove the light bulb from the light housing. Then unclip the light housing from the top radio plate. This will allow you access into the radio to unscrew the two sheet metal screws that fasten the dial drum housing (see step #5).
Attached Images
    
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:02 AM   #4
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

4. Next, remove the front face plate. Remove the flat nuts on the radio shafts. Then, remove the four sheet metal screws holding down the face plate, remove the plate.
Attached Images
     
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:12 AM   #5
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

5. Looking down into the radio as it lays flat right side up, you will see two sheet metal screws-one on the left side, and one on the right side of the radio dial drum housing. Carefully remove each of these screws. You will need to move the radio station from one left, then to the right in orider to allow enough room to access the screws. Be careful not to let the screws fall into the radio. The sheet metal screw on the left has a skinny, flat piece of metal that rests on the dial indicator. Study its resting position before removing so you are confident when it comes time to reinstall the screws.
Attached Images
  
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:17 AM   #6
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

6. From the front face of the radio, carefully remove the dial drum housing. BE CAREFUL as to NOT stress the dial adjustment string...remember, it's 40+ years old and likely to be on the brittle side. Also be careful not to scratch the orange paint on the back side of the indicator needle as you remove the dial drum housing.
Attached Images
    
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:26 AM   #7
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

7. Clean the AM/FM drum with water and a Q-Tip. I did this step out of order. It will actually be easier to clean once you remove the dial drum from its housing.
Attached Images
 
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:34 AM   #8
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

8. Remove the dial drum from its housing: In order to do this without causing any damage, you will have to spin the dial inside of the housing until the little plastic tab on the right end of the plast drum lines up with the hole on the right side of the houseing (shown in this picture). Shift the drum so the little pin slips into the hole. This will allow you carefully lift the left side of the drum up and out of the housing. Be careful to study the position of the tension spring on the right side. Note the direction that it sits on the its pin.
Attached Images
   
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:39 AM   #9
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

9. Next, you will need to prepare your decal. They are printed with a bit of extra black area that you will need to cut off to fit properly. Take some measurements off of your original dial and mark your decal for cutting. Once the decal is cut, remove the backing paper and carefull apply it to the drum. Be careful when applying it so you do not get any air bubbles.
Attached Images
     
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Old 01-21-2012, 04:52 AM   #10
70LonghornCST
Moderator
 
70LonghornCST's Avatar
 
Join Date: Jun 2008
Location: Modesto, CA
Posts: 5,775
Re: Adding an AM/FM Decal

10. Once the decal is firmly in place, reverse the order of removal. Take your time. Be sure to remember when reinstalling the face plate that you line up the AM/FM switch lever with the indicator shaft so it will flip to AM/FM when you move the lever.

Once it's all back together, enjoy your new truck AM/FM radio

I hope this write-up helps.

-Richard
Attached Images
  
__________________
2018 Chevy Crew Cab
2006 Impala SS
1965 Plymouth Sport Fury
1970 Chevy Longhorn
  • Bucket Seats
  • Shoulder Belts
  • Front Tow Hooks
  • Factory Air
  • Factory Speedwarning, Tach & Vaccum
  • Factory Tilt
  • CST Package
  • AM/FM Radio
  • Bumper Guards
Richard

70 Longhorn CST Build

Adding an AM/FM Decal
70LonghornCST is offline  
Closed Thread

Bookmarks


Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 06:40 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com