Ls oil pan - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Nick_c10 · 12-15-2018, 12:04 AM

About to install a 04 5.3 Truck LS in my 68 stepside and was told the oil pan will fit but will hang too low for a lowered truck. Anyone know if the f-body pan will work? I can tell by looking at it that it will be short enough but the lower sump part is longer and I’m not sure if it will clear the cross member. I’d like to hear from someone that has installed it on their swap before I spend $300 on it off eBay. I’ll be using dirty dingo mounts. Thanks.

ls1nova71 · 12-15-2018, 03:30 AM

It will fit, but you have to put it pretty far back. A better pan is a CTSV pan or even the GM Muscle car pan.

**1971Stepside** · 12-15-2018, 09:38 AM

Second the CTSV pan.

**mongocanfly** · 12-15-2018, 12:36 PM

I used a c6 vett wet sump pan...it was the shallowest one I could find with my research...

Nick_c10 · 12-15-2018, 12:43 PM

Thanks guys, ordering one now.

**bigmoe** · 12-15-2018, 07:28 PM

Quote:

Originally Posted by Nick_c10

Thanks guys, ordering one now.

Where are you getting it from? Do you also need pan + matching pickup, dipstick, windage tray?

I'm probably in the same boat with my 65 C10, 3" drop spindles, 2008 5.3 LS from a Tahoe. I'm going with the adapter plates on the engine that allow you several positions. I assumed I would put it back as close to the firewall as possible to keep more room up front.

**1971Stepside** · 12-16-2018, 10:41 AM

If you go CTSV pan you need the pan, pick up tube, dipstick tube and dipstick. The wind age tray is the same. If you need the part numbers let me know. I can find my receipt

**bigmoe** · 12-16-2018, 10:46 AM

Quote:

Originally Posted by 1971Stepside

If you go CTSV pan you need the pan, pick up tube, dipstick tube and dipstick. The wind age tray is the same. If you need the part numbers let me know. I can find my receipt

Sure that would be great.

**1971Stepside** · 12-16-2018, 12:26 PM

CTVS Pan part #12631828 comes with new bolts and gasket
Pick up Tube #12621299
Dipstick tube #12584738
Dipstick #1258437
Windage tray (if you want it) #12611129

12-15-2018, 03:30 AM	#2
ls1nova71 Registered User Join Date: Dec 2009 Location: Independence Mo Posts: 4,117	Re: Ls oil pan It will fit, but you have to put it pretty far back. A better pan is a CTSV pan or even the GM Muscle car pan. __________________ My '72 short bed build. http://www.ls1tech.com/forums/conver...6-0-4l80e.html 5.3 swap into my RUSTY '71 C10 http://ls1tech.com/forums/conversion...71-c-10-a.html

12-15-2018, 09:38 AM	#3
1971Stepside Almost Satisfied Join Date: Mar 2002 Location: Springfield, MO Posts: 2,928	Re: Ls oil pan Second the CTSV pan. __________________ 1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far."

12-15-2018, 12:36 PM	#4
mongocanfly Post Whore Join Date: May 2015 Location: Alabama Posts: 14,581	Re: Ls oil pan I used a c6 vett wet sump pan...it was the shallowest one I could find with my research... __________________ Mongo...aka Greg RIP Dad RIP Jesse 1981 C30 LQ9 NV4500..http://67-72chevytrucks.com/vboard/s...d.php?t=753598 Mongos AD- LS3 TR6060...http://67-72chevytrucks.com/vboard/s...34#post8522334 Columbus..the 1957 IH 4x4...http://67-72chevytrucks.com/vboard/s...63#post8082563 2023 Chevy Z71..daily driver

12-15-2018, 12:43 PM	#5
Nick_c10 Registered User Join Date: Jan 2015 Location: Rapid City SD Posts: 31	Re: Ls oil pan Thanks guys, ordering one now.

12-16-2018, 10:41 AM	#7
1971Stepside Almost Satisfied Join Date: Mar 2002 Location: Springfield, MO Posts: 2,928	Re: Ls oil pan If you go CTSV pan you need the pan, pick up tube, dipstick tube and dipstick. The wind age tray is the same. If you need the part numbers let me know. I can find my receipt __________________ 1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far."

12-15-2018, 12:04 AM	#1
Nick_c10 Registered User Join Date: Jan 2015 Location: Rapid City SD Posts: 31	Ls oil pan About to install a 04 5.3 Truck LS in my 68 stepside and was told the oil pan will fit but will hang too low for a lowered truck. Anyone know if the f-body pan will work? I can tell by looking at it that it will be short enough but the lower sump part is longer and I’m not sure if it will clear the cross member. I’d like to hear from someone that has installed it on their swap before I spend $300 on it off eBay. I’ll be using dirty dingo mounts. Thanks.

12-16-2018, 12:26 PM	#9
1971Stepside Almost Satisfied Join Date: Mar 2002 Location: Springfield, MO Posts: 2,928	Re: Ls oil pan CTVS Pan part #12631828 comes with new bolts and gasket Pick up Tube #12621299 Dipstick tube #12584738 Dipstick #1258437 Windage tray (if you want it) #12611129 __________________ 1971 C10 Stepside. LSx 6.0 with BTR Stage IV, Speed Engineering Headers, 4L80e transmission w/3200 Circle-D Stall. 3.73. Posi. Purchased this truck when I was 17. I started the rebuild (or take apart) in 1993. I have drug it around all over the country in pieces. Finally back on the road in 2021. "I can't complain, but sometimes I still do. Life's been good to me so far."



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.