The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain > Diesel Conversions

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-14-2018, 03:49 PM   #1
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
C20/cummins 12 valve

I got a 12 valve for my next project and I have a few questions for you guys. Donor engine is from a 1989 dodge. It was missing the vacuum pump/power steering. Went out to the junkyard and found one but it donít work. I also found a crack on the housing unit. Would I need to replace it?
Attached Images
  

Last edited by MONTE; 03-19-2018 at 07:33 PM.
MONTE is offline   Reply With Quote
Old 03-14-2018, 11:01 PM   #2
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

Yes, I'd say replace that gear housing or have it welded properly. Those early 1st gens had a diaphragm type vacuum pump and the whole assembly is shorter than the later vane type vac pump setups. You can get the later vane style like you have to work with some mods to the throttle bracket. I'd rather have the later set up anyway.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-14-2018, 11:35 PM   #3
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Thanks for the info. Hopefully I can get the correct 1 or get my refund for the pump.
MONTE is offline   Reply With Quote
Old 03-16-2018, 09:20 AM   #4
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Some pics
Attached Images
     

Last edited by MONTE; 03-19-2018 at 07:37 PM.
MONTE is offline   Reply With Quote
Old 03-16-2018, 09:26 AM   #5
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

more pics
Few upside down, not sure why...
Attached Images
   

Last edited by MONTE; 03-19-2018 at 07:30 PM.
MONTE is offline   Reply With Quote
Old 03-19-2018, 07:16 PM   #6
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

Monte, very cool! That looks like a pretty clean truck. It also appears to be a Longhorn from what I can see from the pics. Do you plan to use that 727? If so you better try to get rear end gears near 3.08 or so.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-19-2018, 07:22 PM   #7
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Im going with the automatic for now until I find a good manual transmission. The truck is a longhorn, it's in great condition.
MONTE is offline   Reply With Quote
Old 03-19-2018, 07:38 PM   #8
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

If you can find a D60 with 3.54 gears from one of these trucks, that would help. Your truck probably has 4.10s unless it was a big block truck.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-20-2018, 12:12 AM   #9
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

My truck is a big block 402 8 lug, I need to look and see what it has.
MONTE is offline   Reply With Quote
Old 03-24-2018, 10:52 AM   #10
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Cooler heater exchanger/converter oil cooler

Where do I find a replacement cooler or do I need it ?
What setup are you guys using?
Would I need to replace the metal line or can I use rubber hoses for the coolant?
They are all rusted.
Attached Images
 
MONTE is offline   Reply With Quote
Old 03-26-2018, 10:21 PM   #11
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

That is the torque converter heat exchanger. On a Texas truck with a 727 I'd just toss it and put a good after market cooler in front of the radiator.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-27-2018, 01:46 AM   #12
Peanutbutter
Senior Member
 
Join Date: Feb 2013
Location: Mesa, Colorado
Posts: 404
Re: C20/cummins 12 valve

When I go down this road again I will put a block off plate on the gear housing and belt drive a common ps pump and go hydraboost. The marriage vacuum pump and ps pump can be a real pain if you get a bad shaft and seal on the ps pump. As long as you have the gear housing off make sure you put a fix on the killer dowl pin or it may destroy the whole motor. I was lucky, dowl pin fell down and instead of going between the two gears it got caught between the gear and tin cover, when I pulled the timing cover it looked like you had shot it with a 45 ACP from the inside out. Could'nt figure out where all the oil was coming from.
Peanutbutter is offline   Reply With Quote
Old 03-29-2018, 06:04 PM   #13
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Thanks for all the information guys. First time working on diesels for me.
Got a few parts today:
Gear housing
Expansion plugs
Water inlet seal
Water pump
Changing all the gaskets other than manifold and head.
Waiting on the Killer dowel pin to come in.
Attached Images
    
MONTE is offline   Reply With Quote
Old 03-29-2018, 06:59 PM   #14
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

Quote:
Originally Posted by Peanutbutter View Post
When I go down this road again I will put a block off plate on the gear housing and belt drive a common ps pump and go hydraboost. The marriage vacuum pump and ps pump can be a real pain if you get a bad shaft and seal on the ps pump. As long as you have the gear housing off make sure you put a fix on the killer dowl pin or it may destroy the whole motor. I was lucky, dowl pin fell down and instead of going between the two gears it got caught between the gear and tin cover, when I pulled the timing cover it looked like you had shot it with a 45 ACP from the inside out. Could'nt figure out where all the oil was coming from.
The power steering pumps have a drive coupler that is pressed on the pump shaft. That is a wear item and can be purchased with a new or reman pump. I can't tell you how many of these vac/ps pumps I've resealed and have no issues with them. I have had some severly worn ones I've had to source odd parts for but I still wouldn't hang a different pump off the side and run another belt to drive it. You can run hydroboost with a non hydroboost pump. You just have to either t the return or add a return to your reservoir on the pump.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-29-2018, 07:02 PM   #15
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

Quote:
Originally Posted by MONTE View Post
Thanks for all the information guys. First time working on diesels for me.
Got a few parts today:
Gear housing
Expansion plugs
Water inlet seal
Water pump
Changing all the gaskets other than manifold and head.
Waiting on the Killer dowel pin to come in.
Buying those parts from Mopar sounds pricey. Make sure you replace the oil cooler gaskets. I'd go ahead and do the cooler too if it has a lot of miles on it. Those early ones are known to leak and cause headaches. Make sure if your crankshaft has a groove worn in it that you get a seal with a wear sleeve other wise you will be having leaks again. That goes with the rear main seal too.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-30-2018, 12:09 AM   #16
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

I'll look into the oil cooler next.
Looks like a reman one will run about $200-$300.
Should I apply any type of permatex with the expansion plugs or just press them in?
MONTE is offline   Reply With Quote
Old 03-30-2018, 05:13 PM   #17
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

Which expansion plugs?
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-30-2018, 06:33 PM   #18
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Core plugs/freeze plugs.
MONTE is offline   Reply With Quote
Old 03-30-2018, 10:45 PM   #19
Dieselwrencher
6>8 Plugless........

 
Dieselwrencher's Avatar
 
Join Date: Sep 2007
Location: Mitchellville, Ia
Posts: 14,951
Re: C20/cummins 12 valve

Red lock tite is what I use but usually I put in billet ones. You could use permatex rated for coolant though.
__________________
Ryan
1972 Chevy Longhorn K30 Cheyenne Super, 359 Inline 6 cylinder, Auto Trans, Tilt, Diesel Tach/Vach, Buckets, Rare Rear 4-link and air ride option Build Thread
1976 K30 CC SWB Build Thread

Tired of spark plugs? Check this out.
Dieselwrencher is offline   Reply With Quote
Old 03-31-2018, 09:52 PM   #20
MONTE
Registered User
 
MONTE's Avatar
 
Join Date: Oct 2005
Location: El Paso, Texas
Posts: 195
Re: C20/cummins 12 valve

Got the KDP today.
Attached Images
 
MONTE is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 07:11 PM.


Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2018, vBulletin Solutions, Inc.
Copyright 1997-2013 67-72chevytrucks.com