The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > 47 - Current classic GM Trucks > The 1947 - 1959 Chevrolet & GMC Pickups Message Board

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 03-08-2018, 03:01 AM   #1
MiraclePieCo
Registered User
 
MiraclePieCo's Avatar
 
Join Date: Sep 2014
Location: USA
Posts: 2,249
Mechanical Fan Question

In my penchant for keeping things old school, I'll be using a mechanical fan on my 51 panel with a stock 350 SBC. As you all know, that places the fan pretty low on the radiator - maybe just covering half of the fin area. How about it you mechanical fan users - I see lots of you doing this, so I'm assuming it still must cool adequately?
Attached Images
 

Last edited by MiraclePieCo; 03-08-2018 at 05:05 AM.
MiraclePieCo is offline   Reply With Quote
Old 03-08-2018, 12:49 PM   #2
jackson
Registered User
 
Join Date: Jan 2012
Location: el campo texas
Posts: 322
Re: Mechanical Fan Question

I built an ofset fan shroud. Havent tried it yet but its a stock 283 so i dont see any problems
jackson is offline   Reply With Quote
Old 03-08-2018, 03:11 PM   #3
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,660
Re: Mechanical Fan Question

fan shroud is the trick to getting any fan to work efficiently
and the time to build it is now while you have good access to everything
__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Old 03-09-2018, 03:42 AM   #4
Softpatch
Registered User
 
Softpatch's Avatar
 
Join Date: Sep 2013
Location: Vashon WA
Posts: 969
Re: Mechanical Fan Question

Quote:
Originally Posted by MiraclePieCo View Post
In my penchant for keeping things old school, I'll be using a mechanical fan on my 51 panel with a stock 350 SBC. As you all know, that places the fan pretty low on the radiator - maybe just covering half of the fin area. How about it you mechanical fan users - I see lots of you doing this, so I'm assuming it still must cool adequately?
.

.
Why again do you want to run a mech fan.?
Do you also Have the old school foot starter
Generator/Voltage regulator set up
Got your set of ply tires on all four corners too.?

I'm pretty sure You 1951 panel was not stock with that 350

Stop with the "Keeping thing Old school" Nonsense

sure you can make a Shroud to fit that fan on that frame for that motor
or stop the madness and hookup an electric two speed fan
Fan and controller under $75
__________________
My Spelling is Not Incorrect...It's 'Creative'
.
.
1966 C-20 .....Swap 91 G-30(5.7 FI)/4L80E
http://67-72chevytrucks.com/vboard/s...d.php?t=789617
59 Viking Revival .. http://67-72chevytrucks.com/vboard/s...d.php?t=632341
Softpatch is offline   Reply With Quote
Old 03-09-2018, 05:31 AM   #5
MiraclePieCo
Registered User
 
MiraclePieCo's Avatar
 
Join Date: Sep 2014
Location: USA
Posts: 2,249
Re: Mechanical Fan Question

Quote:
Originally Posted by Softpatch View Post
.

.
Why again do you want to run a mech fan.?
Do you also Have the old school foot starter
Generator/Voltage regulator set up
Got your set of ply tires on all four corners too.?

I'm pretty sure You 1951 panel was not stock with that 350

Stop with the "Keeping thing Old school" Nonsense

sure you can make a Shroud to fit that fan on that frame for that motor
or stop the madness and hookup an electric two speed fan
Fan and controller under $75

My question was not which type of fan I should run. I've built numerous cars using both electric and mechanical fans respectively and I've found the mechanical much more to my liking for several reasons, primarily simplicity and it's cousin, reliability. Too many electric fan failures of thermostats, wiring or motors. And by "old school" I mean 1960s or '70s era technology, not 1940s - no power anything, no electric anything. However I don't want to let this question digress into a mechanical vs electric fan debate; my mind is made up. You build your car and I'll build mine, thank you. If however you have some actual experience with a low fan on an AD radiator and can answer my question, I'm all ears.

Last edited by MiraclePieCo; 03-09-2018 at 05:54 AM.
MiraclePieCo is offline   Reply With Quote
Old 03-09-2018, 08:52 AM   #6
Katrina/10
Registered User
 
Katrina/10's Avatar
 
Join Date: Oct 2010
Location: Ocean Springs, MS
Posts: 1,746
Re: Mechanical Fan Question

I put a V8 in my 51 years ago and ran a solid mounted flex fan just like yours. It turned out the same way, with the bottom fan blades below the radiator. I had no fan shroud at all. It never caused a problem with overheating, although I didn't really like the way it looked. I left it that way until I added air conditioning, then went to an electric fan to get better air flow through the condenser while moving slow.
__________________
Gary

1971 Chevrolet C/10
1951 GMC 100
1977 GMC C15
1955 Chevrolet 3100
Katrina/10 is offline   Reply With Quote
Old 03-11-2018, 03:49 AM   #7
Softpatch
Registered User
 
Softpatch's Avatar
 
Join Date: Sep 2013
Location: Vashon WA
Posts: 969
Re: Mechanical Fan Question

__________________
My Spelling is Not Incorrect...It's 'Creative'
.
.
1966 C-20 .....Swap 91 G-30(5.7 FI)/4L80E
http://67-72chevytrucks.com/vboard/s...d.php?t=789617
59 Viking Revival .. http://67-72chevytrucks.com/vboard/s...d.php?t=632341

Last edited by Softpatch; 03-11-2018 at 11:33 PM.
Softpatch is offline   Reply With Quote
Old 03-11-2018, 04:55 AM   #8
MiraclePieCo
Registered User
 
MiraclePieCo's Avatar
 
Join Date: Sep 2014
Location: USA
Posts: 2,249
Re: Mechanical Fan Question

Since this thread is now officially degenerating, I'll add this fan experience:

In recent years I built two cars of similar vintage, both with SBCs, tri-power and Mustang radiators. One had a cheapo swap meet flex fan, the other featured a top-of-the-line Spal 16" electric fan with custom aluminum shroud.

Guess which one ran cool and which one ran hot...
MiraclePieCo is offline   Reply With Quote
Old 03-11-2018, 08:52 AM   #9
Desert1957
Registered User
 
Desert1957's Avatar
 
Join Date: Apr 2009
Location: New Freedom Pa.
Posts: 1,335
Re: Mechanical Fan Question

Quote:
Originally Posted by MiraclePieCo View Post
Since this thread is now officially degenerating, I'll add this fan experience:

In recent years I built two cars of similar vintage, both with SBCs, tri-power and Mustang radiators. One had a cheapo swap meet flex fan, the other featured a top-of-the-line Spal 16" electric fan with custom aluminum shroud.

Guess which one ran cool and which one ran hot...
X2

FYI, here is my 34 Coupe, 355 SBC "Mechanical" fan and fuel pump. runs cool in all weather.

I too am a believer in simple is better. IMO more reliable.

Name:  13230159_1784350928468426_8283342778722642180_n - Copy.jpg
Views: 233
Size:  43.1 KB
__________________
Desert
Desert1957 is offline   Reply With Quote
Old 03-11-2018, 09:43 AM   #10
Purcell69
Registered User
 
Join Date: Jul 2013
Location: Central OK
Posts: 521
Re: Mechanical Fan Question

Like was previously suggested, a fan shroud is the answer. Build one that is offset with enough room for air to be drawn down from the top of the radiator and you will be fine, maybe 2" away from the rear side of the fins at the top.

-Joe
__________________
My '57 "Ram-rolet" not a NAPCO build: http://67-72chevytrucks.com/vboard/s...d.php?t=589917
Purcell69 is offline   Reply With Quote
Old 03-11-2018, 11:19 AM   #11
Black_Sheep
Registered User
 
Black_Sheep's Avatar
 
Join Date: Jun 2017
Location: upper midwest
Posts: 1,129
Re: Mechanical Fan Question

Speedway has a kit to raise the fan 5". it used a 6 cylinder water pump...
https://www.speedwaymotors.com/Zips-...Kit,58831.html
Black_Sheep is offline   Reply With Quote
Old 03-11-2018, 02:13 PM   #12
mr48chev
Registered User
 
mr48chev's Avatar
 
Join Date: Jul 2007
Location: Toppenish, WA
Posts: 15,244
Re: Mechanical Fan Question

That Zips water pump riser kit that Black Sheep showed is a common Small block in a street rod get the fan up where it needs to be piece of equipment. It should let you run a slightly larger fan too.

I've never been too found of electric fans myself. It's not just "old school" it is simplicity and function.
__________________
Founding member of the too many projects, too little time and money club.

My ongoing truck projects:
48 Chev 3100 that will run a 292 Six.
71 GMC 2500 that is getting a Cad 500 transplant.
77 C 30 dualie, 454, 4 speed with a 10 foot flatbed and hoist. It does the heavy work and hauls the projects around.
mr48chev is offline   Reply With Quote
Old 03-11-2018, 02:49 PM   #13
dsraven
Registered User
 
Join Date: Nov 2010
Location: calgary alberta
Posts: 7,773
Re: Mechanical Fan Question

there is also a medium duty truck set up that used a high mounted mechanical fan set up. just don't remember the application. I did a quick google search but didn't come up with anything. maybe it was a big block thing, can't remember. it would get the fan up in the middle of the rad area for sure. then build a fan shroud that works. here is a tech article from the HAMB that moves the water pump up so the fan sits higher on the rad.

https://www.jalopyjournal.com/forum/...al-fan.168231/

here is a hotrod network version of building your own fan shroud from metal

http://www.hotrod.com/articles/1006s...d-fabrication/

and fiberglass from a different site

http://www.route66hotrodhigh.com/FanShroud.html


this is hotrodding, your truck, do what you like. consider the advice given but do what you want, as long as it is safe for you and everybody else driving on the same roads.
dsraven is offline   Reply With Quote
Old 03-11-2018, 03:35 PM   #14
Clarance J
Registered User
 
Clarance J's Avatar
 
Join Date: Feb 2013
Location: Grants Pass Oregon
Posts: 473
Re: Mechanical Fan Question

Hello MiraclePieCo. I had to fab my own fan shroud be cause of all the same reasons you gave above. This is the second shroud I built. The first one just didn't get the job done. I switched back to mechanical to solve my over heating problems. Its a little bit of work but it looks half way decent and works very well. Here is a picture of it done (minus the paint). How I made the shroud can be found in my thread "Just another old truck" by Clarance J in the projects and builds. I haven't posted in awhile so I had to go back and hunt myself down. You will find it on page 4 projects & builds. Then page 14 starting with post 333.

Earl
Attached Images
 
__________________
You have to have patiences or you'll be one.
Clarance J is offline   Reply With Quote
Old 03-11-2018, 11:03 PM   #15
MiraclePieCo
Registered User
 
MiraclePieCo's Avatar
 
Join Date: Sep 2014
Location: USA
Posts: 2,249
Re: Mechanical Fan Question

I'm not a fan (accidental pun) of shrouds; by covering so much of the radiator's surface they block ambient air flow through the fins when the fan isn't pulling.

For example: a radiator that's 20" wide and 20" tall has a surface area of 400 square inches on it's front side. But on the back side the fan opening for a 16-inch fan is only 254 square inches (3.14x9x9 fan radius squared). THE SHROUD HAS JUST COST YOU 160 SQUARE INCHES OF COOLING SURFACE!

For that reason many custom shrouds have resorted to rubber flaps to allow air flow, like the picture below. Still a poor trade off in my opinion.
Attached Images
 
MiraclePieCo is offline   Reply With Quote
Old 03-11-2018, 11:09 PM   #16
MiraclePieCo
Registered User
 
MiraclePieCo's Avatar
 
Join Date: Sep 2014
Location: USA
Posts: 2,249
Re: Mechanical Fan Question

Quote:
Originally Posted by dsraven View Post
here is a tech article from the HAMB that moves the water pump up so the fan sits higher on the rad.

https://www.jalopyjournal.com/forum/...al-fan.168231/
Ha ha dsraven, the HAMB guy really sums it up!

Because I believe that electric fans belong on Japanese cars with fart can exhaust ... and they are NOT needed on a Hot Rod, I will not run a electric fan on my Hot Rods.

And the Street Rodder article was pretty emphatic too:

...even electric-fan manufacturers will begrudgingly tell you that all things being equal a belt-driven fan with a shroud around it is about the most effective cooling option going.

Last edited by MiraclePieCo; 03-12-2018 at 02:01 AM.
MiraclePieCo is offline   Reply With Quote
Old 03-11-2018, 11:11 PM   #17
MiraclePieCo
Registered User
 
MiraclePieCo's Avatar
 
Join Date: Sep 2014
Location: USA
Posts: 2,249
Re: Mechanical Fan Question

Quote:
Originally Posted by Clarance J View Post
Hello MiraclePieCo. I had to fab my own fan shroud be cause of all the same reasons you gave above.
Earl
Awesome work Earl. That shroud is definitely needed since your fan is so far back from your radiator. And it's relatively open to allow the free flow of ambient air at speed. Nice job!
MiraclePieCo is offline   Reply With Quote
Old 03-12-2018, 01:13 PM   #18
_Ogre
Registered User
 
_Ogre's Avatar
 
Join Date: Jan 2012
Location: Motown
Posts: 7,660
Re: Mechanical Fan Question

Quote:
Originally Posted by Clarance J View Post
I haven't posted in awhile so I had to go back and hunt myself down.
nice well built shroud

put your build thread in your signature, read my signature
__________________
cool, an ogre smiley Ogre's 58 Truk build

how to put your truck year and build thread into your signature
shop air compressor timer
_Ogre is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 03:31 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com