1960 door glass install - The 1947 - Present Chevrolet & GMC Truck Message Board Network

Chev1171 · 11-13-2019, 07:44 PM

Removed my door glass to repair regulator rollers. Need help re-installing door glass into regulator track

**The Rocknrod** · 11-14-2019, 05:15 PM

This thread - http://67-72chevytrucks.com/vboard/s...d.php?t=578824

jbgroby · 11-18-2019, 12:49 PM

Chev,
I made a picture tutorial when I installed my vents and glass. I hope this helps.

Step 9: Attaching the Regulator to the Glass Frame

Ok, so far it’s been a bit long, but this step may find you cussing a little. You now need to fit the upper rollers in the window grove channel. BUT HOW YOU ASK - AS THEY DON’T MATCH UP. You will need to undo the two screws holding the groove to the window frame, have your helper hold onto the window in case it wants to slip, but I found that the tension and the felt held mine in place. You then slide the grooved channel over both rollers, you work the channel back and forth till you can get over the rollers and reset the screws. You will need to roll the regulator up sill it in the position shown. This seems hard but it is not. Once you put the screws back, you need to cycle the window a few times to see if it binds. Sometime a bit of graphite may be needed in the groves.

http://67-72chevytrucks.com/vboard/s...d.php?t=718048

11-13-2019, 07:44 PM	#1
Chev1171 Registered User Join Date: Aug 2013 Location: Ontario Canada Posts: 2	1960 door glass install Removed my door glass to repair regulator rollers. Need help re-installing door glass into regulator track

11-14-2019, 05:15 PM	#2
The Rocknrod Moderator Join Date: Aug 2011 Location: China Spring, TX Posts: 7,280	Re: 1960 door glass install This thread - http://67-72chevytrucks.com/vboard/s...d.php?t=578824 __________________ Master Chief, US Navy, Retired 1964 C10 Step-side Short Bed - In Progress 2009 2500HD Duramax LTZ 1948 GMC Panel 1956 Big Window Stepside 1953 5 Window Chevy Stepside 1932 Coupe New Seat Foam for Bench Seats?

11-18-2019, 12:49 PM	#3
jbgroby Registered User Join Date: Nov 2008 Location: Lacombe, LA Posts: 2,768	Re: 1960 door glass install Chev, I made a picture tutorial when I installed my vents and glass. I hope this helps. Step 9: Attaching the Regulator to the Glass Frame Ok, so far it’s been a bit long, but this step may find you cussing a little. You now need to fit the upper rollers in the window grove channel. BUT HOW YOU ASK - AS THEY DON’T MATCH UP. You will need to undo the two screws holding the groove to the window frame, have your helper hold onto the window in case it wants to slip, but I found that the tension and the felt held mine in place. You then slide the grooved channel over both rollers, you work the channel back and forth till you can get over the rollers and reset the screws. You will need to roll the regulator up sill it in the position shown. This seems hard but it is not. Once you put the screws back, you need to cycle the window a few times to see if it binds. Sometime a bit of graphite may be needed in the groves. http://67-72chevytrucks.com/vboard/s...d.php?t=718048 __________________ http://s1299.photobucket.com/user/jb...23904108567829 Last edited by jbgroby; 11-19-2019 at 01:46 PM.



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.