correct Cheyenne fender emblem hole location - The 1947 - Present Chevrolet & GMC Truck Message Board Network

**nitrosport_5** · 05-31-2013, 11:31 PM

I've searched the entire assembly manual book for the measurements but can't find it. where is the correct location for the holes for the Cheyenne 20 emblem. my 8 350 emblem was way off and not straight so I don't trust that the person put the other in the correct spot. I seem to be able to find every other measurement but that one. unless I just missed it somewhere.

thanks in advance!

and I should add, this is on a '72
Posted via Mobile Device

SS Tim · 05-31-2013, 11:55 PM

This came from the board, somewhere just running threads in the middle of the night. Unlike most of my information I cannot attest to it being accurate. So please cross check it.

**nitrosport_5** · 05-31-2013, 11:59 PM

thanks Tim! I'll check the location on both fenders that I have .

do you happen to have a Monte Carlo SS as well? I seem to recall that username/picture from those forums.
Posted via Mobile Device

SS Tim · 06-01-2013, 12:28 AM

Negative on the Monte. If you see me it will be mostly in the Camaro 1st and 4th gen. forums even then very little.

**nitrosport_5** · 06-01-2013, 12:41 AM

gotcha. Musta been someone else. thanks for the info though. I'll report what the differences are on my 2 fenders. they're off 2 different trucks, one I trust 10x more than the other haha
Posted via Mobile Device

05-31-2013, 11:31 PM	#1
nitrosport_5 Senior Member Join Date: Jul 2012 Location: St. John, Washington Posts: 617	correct Cheyenne fender emblem hole location I've searched the entire assembly manual book for the measurements but can't find it. where is the correct location for the holes for the Cheyenne 20 emblem. my 8 350 emblem was way off and not straight so I don't trust that the person put the other in the correct spot. I seem to be able to find every other measurement but that one. unless I just missed it somewhere. thanks in advance! and I should add, this is on a '72 Posted via Mobile Device __________________ "Rusty" 1972 K20 Cheyenne Super, 496, A/C, Tilt, Tach, Buckets, 4l80e/NP205, 4" Rancho Lift, 35" BFG AT "Ramp Truck" 1972 C30 Ramp Truck 350, Air Bags, Factory A/C. "1968" C10 Shortbed project

05-31-2013, 11:55 PM	#2
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,504	Re: correct Cheyenne fender emblem hole location This came from the board, somewhere just running threads in the middle of the night. Unlike most of my information I cannot attest to it being accurate. So please cross check it. Attached Images __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban

05-31-2013, 11:59 PM	#3
nitrosport_5 Senior Member Join Date: Jul 2012 Location: St. John, Washington Posts: 617	Re: correct Cheyenne fender emblem hole location thanks Tim! I'll check the location on both fenders that I have . do you happen to have a Monte Carlo SS as well? I seem to recall that username/picture from those forums. Posted via Mobile Device __________________ "Rusty" 1972 K20 Cheyenne Super, 496, A/C, Tilt, Tach, Buckets, 4l80e/NP205, 4" Rancho Lift, 35" BFG AT "Ramp Truck" 1972 C30 Ramp Truck 350, Air Bags, Factory A/C. "1968" C10 Shortbed project

06-01-2013, 12:28 AM	#4
SS Tim Registered User Join Date: Aug 2010 Location: Edwards, CA Posts: 7,504	Re: correct Cheyenne fender emblem hole location Negative on the Monte. If you see me it will be mostly in the Camaro 1st and 4th gen. forums even then very little. __________________ Thanks, Tim * VIN/Model Decoders * Power Team Charts (engine/transmission/gear ratio) * Post Your Pickup SPID Blazer SPID Suburban/Panel SPID * RTFM ... Read The Factory Manuals... download 'em here Highlanders Do you have a 1972 Plaid Pickup? Plaid Blazer ** Plaid Suburban

06-01-2013, 12:41 AM	#5
nitrosport_5 Senior Member Join Date: Jul 2012 Location: St. John, Washington Posts: 617	Re: correct Cheyenne fender emblem hole location gotcha. Musta been someone else. thanks for the info though. I'll report what the differences are on my 2 fenders. they're off 2 different trucks, one I trust 10x more than the other haha Posted via Mobile Device __________________ "Rusty" 1972 K20 Cheyenne Super, 496, A/C, Tilt, Tach, Buckets, 4l80e/NP205, 4" Rancho Lift, 35" BFG AT "Ramp Truck" 1972 C30 Ramp Truck 350, Air Bags, Factory A/C. "1968" C10 Shortbed project



Register or Log In To remove these advertisements.

Register or Log In To remove these advertisements.