The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Electrical

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-23-2010, 12:56 PM   #26
stellar
Registered User
 
Join Date: May 2009
Location: Pittsburgh Pa.
Posts: 126
Re: Question on starter wiring

The starter is ok the solenoid needs changed to one with 2 small posts instead of 1. Purple wire to the small post you have now. Should be marked S. When you get the sol with 2 small posts the yellow wire will go from the other small post on solenoid marked R to the coil.
stellar is offline   Reply With Quote
Old 07-23-2010, 01:06 PM   #27
fixit-p
Registered User
 
fixit-p's Avatar
 
Join Date: Dec 2008
Location: Yay Area CA
Posts: 2,329
Re: Question on starter wiring

If your starter solenoid only has 1 terminal it would be the "S" terminal so that would be for the purple wire. The yellow wire is needed on points type ignitions to provide full battery voltage while the engine is cranking for easier starts. With that solenoid you have 3 options (IMO) 1, convert to HEI. 2, install a remote starter solenoid (Ford style) that has an "R" terminal and 3, use a bosh type relay to actuate off of the purple wire and supply batt voltage to the yellow wire.

Edit>>Was typing while stellar posted, I agree you can also just change the solenoid for a 4th option.
__________________
1965 GMC shortwide big window
1969 Chevy C20 long (for now)
2005 Silverado 2500HD Crew Cab


Quote:
Originally posted by:Abraham Lincoln "The trouble with quotes on the Internet is that it is nearly impossible to discern if they are genuine."

Last edited by fixit-p; 07-23-2010 at 01:10 PM.
fixit-p is offline   Reply With Quote
Old 07-23-2010, 01:47 PM   #28
robzilla
Registered User
 
robzilla's Avatar
 
Join Date: Nov 2009
Location: castlegar,b.c
Posts: 277
Re: Question on starter wiring

thanks for the info. i took some pics of the unit, and the one post is broken off. i was going to change to hei, but the unit i got from my brother has the hook up for a computer controller, thus making it not good for the truck. i am searching for another hei unit, that would work for this truck... the search continues. i'll hook up the purple wire, and turn over the engine to get it to tdc to allow for install of the distributor, and then pull the starter to change the solenoid.
robzilla is offline   Reply With Quote
Old 07-23-2010, 09:49 PM   #29
raycow
Registered User
 
Join Date: Mar 2003
Location: San Francisco, CA USA
Posts: 2,454
Re: Question on starter wiring

Quote:
Originally Posted by robzilla View Post
i'm running points system, and the starter only has 2 terminals. the large one for the battery, and another smaller one. of the yellow and purple wires, which would go onto the smaller starter terminal. this starter was taken out of a 71 gmc. or will this starter not work? and where would the other wire go to?
Just so you know, a points system will start and run without the yellow wire or anything else connected to the R terminal. The only time you might need the R teminal is in cold weather, but in summer you certainly don't. A lot of people don't want to believe this - until they try it.

Tape up the starter end of the yellow wire so it doesn't short against anything, because it will be hot when the ignition switch is on.

Ray
raycow is offline   Reply With Quote
Old 08-16-2016, 04:02 PM   #30
chev71c10 Australia
Registered User
 
Join Date: Jan 2016
Location: Melbourne Victoria
Posts: 1
Re: Question on starter wiring

Quote:
Originally Posted by fixit-p View Post
14 gauge is too small, stock is 12 gauge and the heat it's exposed to raises the resistance and is one of the cause of not starting when hot (also referred to as heat soak) 14 gauge will make it worst, the best thing you could do for that is the remote solenoid mod. http://madelectrical.com/catalog/st-1.shtml as far as the yellow wire 20 gauge is stock.
HI i had the same problem i fitted a fifty amp wire to the ignition . my starter war overheating and gave me the ****s . I have a high 2.9 high torque starter.
It has a polished allumminnium mounting block that bolts to the engine.I undid the allan key bolts the attatch the starter to the mount and rotated the starter within the mount 180 Degrees to try to settle the overheating problem.
The mount stays the same You end with the solinoid facing the road.
the starter never overheats and you dont need the seperate solinoid EASY FIX
hopethe helps cheers matt
chev71c10 Australia is offline   Reply With Quote
Old 04-06-2019, 08:02 AM   #31
bpmack16
Registered User
 
Join Date: Sep 2013
Location: Andover
Posts: 156
Re: Question on starter wiring

I just redid my engine wiring harness. The problem I'm having now is the wire coming from the metering block to the starter also has 2 yellow wires connected to it like a Y, the two Uper parts of the Y are yellow wires and the base is the purple/pink wire I can't tell the exact color as the wire is old. But anyway truck ran fine for a day. After that the wire connected to the Y yellow wires melted all most burning up the truck. I believe one yellow wire goes to the HGI and the other to the starter then both connect to that purple/ pink with that states do not cut. So where is this messed up and why is it burning up the wires. O and the part that connects to the starter is on the small post closest to the block.
bpmack16 is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 02:59 PM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Copyright 1997-2013 67-72chevytrucks.com