The 1947 - Present Chevrolet & GMC Truck Message Board Network







Register or Log In To remove these advertisements.

Go Back   The 1947 - Present Chevrolet & GMC Truck Message Board Network > General Truck Forums > Engine & Drivetrain

Web 67-72chevytrucks.com


Reply
 
Thread Tools Display Modes
Old 07-25-2020, 01:16 PM   #1
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
396 experts need help

Hey Guys,

I rebuilt my 396 which is a 69 block. Have the Camaro Heads with a Melling MT6 RV Cam. I ended up Putting Poly locks as the replacement Rocker nuts kept coming loose. Factory ones stayed tight. It has 20-50 oil with Zinc additive and 50 PSI oil pressure at idle with a mechanics oil gauge hooked up. Sounds great when cold. Once it hits 185 - 190 degrees , it idles a little rough and sounds like lifters clacking. Done valve adjustment 10 times. I used 3/4 turn. Tried 3 different oils........ If I missed one of the oil plugs for lifter galley on front of motor behind the timing gear , Would I still have 50 psi ? (Doubt it !) . Plugs are staying white so I am thinking it is also lean. Compression is 150 psi all 8 cylinders.......... What else ? Almost ready to yank it and build another motor. I pulled the Bypass valve this morning and it seems good. No gasket although I do not think that would change much other than possibly mixing a tiny bit of unfiltered oil with filtered oil ?
69 customcamper is offline   Reply With Quote
Old 07-25-2020, 01:29 PM   #2
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: 396 experts need help

Why such a thick oil ?
Most guys i know run 10/40 or even 5/30

20/50 is a diesel truck oil

Do you have headers?
Are they loose

Have you used comp cam lifters i have heard there fairly noisy
gmc684x4 is offline   Reply With Quote
Old 07-25-2020, 01:35 PM   #3
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by gmc684x4 View Post
Why such a thick oil ?
Most guys i know run 10/40 or even 5/30

20/50 is a diesel truck oil

Do you have headers?
Are they loose

Have you used comp cam lifters i have heard there fairly noisy
I tried 5/30 and oil pressure dropped to 25 when it got warm.

I have cast manifolds and yes I hear a slight exhaust leak which I am going to address this weekend. But that should not make it idle rough as the noise increases or am I wrong ? Bolts are very tight.

Standard melling brand Hydraulic lifters. Started with a chinese brand which I swapped already as at first a few would not pump up.
69 customcamper is offline   Reply With Quote
Old 07-25-2020, 01:50 PM   #4
weim55
Registered User
 
Join Date: Jan 2017
Location: Larkspur, Colorado
Posts: 904
Re: 396 experts need help

Is your 50 psi idle oil pressure reading with the engine and operating temperature or cold? What is the oil pressure hot at cruise rpm?

Steve weim55 Colorado
weim55 is offline   Reply With Quote
Old 07-25-2020, 01:54 PM   #5
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: 396 experts need help

Have you tried 10/40 ?

Did you check for coil bind on the valves?
gmc684x4 is offline   Reply With Quote
Old 07-25-2020, 02:04 PM   #6
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: 396 experts need help

Quote:
Originally Posted by 69 customcamper View Post
I tried 5/30 and oil pressure dropped to 25 when it got warm.



Standard melling brand Hydraulic lifters. Started with a chinese brand which I swapped already as at first a few would not pump up.
Nothing wrong with 25 psi hot idle. You only need 7-10 per 1000 rpm.

When you changed lifters did you try to break the cam/lifters in again.
Sounds a lot like a cam getting wiped.
Big blocks are notorious for wiped cams.
geezer#99 is offline   Reply With Quote
Old 07-25-2020, 02:35 PM   #7
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by weim55 View Post
Is your 50 psi idle oil pressure reading with the engine and operating temperature or cold? What is the oil pressure hot at cruise rpm?

Steve weim55 Colorado

It is 50 psi weather cold or hot . So cal has not been to cold in the mornings lately. It will go up to 55-65 depending on speed.
69 customcamper is offline   Reply With Quote
Old 07-25-2020, 02:36 PM   #8
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by geezer#99 View Post
Nothing wrong with 25 psi hot idle. You only need 7-10 per 1000 rpm.

When you changed lifters did you try to break the cam/lifters in again.
Sounds a lot like a cam getting wiped.
Big blocks are notorious for wiped cams.
When I removed the lifters the cam looked fine. Also it is not noisy until you drive it and it warms up . When it got to 25psi It was even noisier.
69 customcamper is offline   Reply With Quote
Old 07-25-2020, 03:04 PM   #9
geezer#99
Registered User
 
geezer#99's Avatar
 
Join Date: Aug 2009
Location: Bowser
Posts: 13,494
Re: 396 experts need help

Of course the cam looked fine. Lifters and cam wear in togethor.
Changing the lifters likely changed that.

Pop the valve covers off and check all the rockers are moving the same.
geezer#99 is offline   Reply With Quote
Old 07-25-2020, 03:15 PM   #10
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by geezer#99 View Post
Of course the cam looked fine. Lifters and cam wear in togethor.
Changing the lifters likely changed that.

Pop the valve covers off and check all the rockers are moving the same.
Ok . I will look when the motor is hot to see if I can spot the change. I cut window in a pair of valve covers for purposes of valve adjustment.
69 customcamper is offline   Reply With Quote
Old 07-25-2020, 03:33 PM   #11
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: 396 experts need help

Did you have machinist check valves for your cam lift for binding issues ?
gmc684x4 is offline   Reply With Quote
Old 07-25-2020, 03:50 PM   #12
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by gmc684x4 View Post
Did you have machinist check valves for your cam lift for binding issues ?
All new springs and stainless steel valves. He said they were good for a much more aggressive Cam. Mine is just one notch up as I just wanted low end torque.
69 customcamper is offline   Reply With Quote
Old 07-25-2020, 04:03 PM   #13
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: 396 experts need help

That is a big check mark of not an issue valve binding can wipe the cam as well

Did the machinist check the new spring rates match the cam too heavy a spring can be hard on the cam too
gmc684x4 is offline   Reply With Quote
Old 07-27-2020, 08:35 AM   #14
HO455
Post Whore
 
HO455's Avatar
 
Join Date: Feb 2016
Location: Portland Oregon
Posts: 10,752
Re: 396 experts need help

I'm a bit confused on the time line of events. You rebuilt the motor with Chinese lifters and then you couldn't get them to pump up and so you replaced them.
Was that before you fired the engine for the first time and broke the cam in?
When you said they wouldn't pump up what exactly do you mean?
What is the part number of the new lifters?
__________________
Thanks to Bob and Jeanie and everyone else at Superior Performance for all their great help.
RIP Bob Parks.
1967 Burban the WMB,1991 S(stink)-10 Blazer,1969 GTO, 1970 Javelin, 1952 F2 Ford 4X4, 29 Model A, 72 Firebird. 85 Alfa Romeo
If it breaks I didn't want it in the first place
The WMB repair thread http://67-72chevytrucks.com/vboard/s...d.php?t=698377
HO455 is offline   Reply With Quote
Old 07-27-2020, 10:34 AM   #15
JMac11
Registered User
 
JMac11's Avatar
 
Join Date: May 2005
Location: Tallahassee Fl
Posts: 773
Re: 396 experts need help

When you tighten the set screw on poly locks it acks the initial adjustment off. If you tight them up without the set screw sufficiently backed off it will crack the poly lock. Poly locks on hydraulic cams are a pain in general
JMac11 is offline   Reply With Quote
Old 07-27-2020, 01:00 PM   #16
j_cst_10
Senior Member
 
j_cst_10's Avatar
 
Join Date: Nov 2008
Location: Cleveland, OH
Posts: 575
Re: 396 experts need help

I would just verify your procedure for adjusting the valve lash is correct.

An easy way to do it quickly is mark the distributor body with a marker where each terminal is on the cap. Verify your at #1 TDC with the rotor pointing at the correct terminal. Adjust both rockers on #1 for 1/2-3/4 turn after zero lash. Remember with poly locks to go the half turn or so, back off an 1/8 of a turn and seat the set screw and then turn the rest of the way.

You can mark your balancer with a mark every 90 degrees as well and run through the same procedure.

Then repeat going through the firing order using your distributor body as reference.
__________________
1972 Cheyenne Super 20 Custom Camper 12 Valve Cummins/5spd manual
1972 Cheyenne Super Short Bed 557 Med Olive DK olive
1970 K5 Blazer Dark Gold

1966 Coronet 440 35k mile survivor
1991 Suburban 2500 454/4L80E 2wd
1985 Monte Carlo SS 383 Sbc, t-56 magnum 6spd and Ford 9"

Last edited by j_cst_10; 07-27-2020 at 01:07 PM.
j_cst_10 is offline   Reply With Quote
Old 07-30-2020, 10:34 AM   #17
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by j_cst_10 View Post
I would just verify your procedure for adjusting the valve lash is correct.

An easy way to do it quickly is mark the distributor body with a marker where each terminal is on the cap. Verify your at #1 TDC with the rotor pointing at the correct terminal. Adjust both rockers on #1 for 1/2-3/4 turn after zero lash. Remember with poly locks to go the half turn or so, back off an 1/8 of a turn and seat the set screw and then turn the rest of the way.

You can mark your balancer with a mark every 90 degrees as well and run through the same procedure.

Then repeat going through the firing order using your distributor body as reference.
I cut a window into a valve cover and adjusted them with engine running. Anybody oppose ? I have tried with running and without. Does not seem to change anything.
69 customcamper is offline   Reply With Quote
Old 07-30-2020, 10:48 AM   #18
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by HO455 View Post
I'm a bit confused on the time line of events. You rebuilt the motor with Chinese lifters and then you couldn't get them to pump up and so you replaced them.
Was that before you fired the engine for the first time and broke the cam in?
When you said they wouldn't pump up what exactly do you mean?
What is the part number of the new lifters?
So the first lifters I ran 100 miles. It was only 2 or 3 that would not pump up. So I replaced all 16 with Melling JB817 which are usually the ones I use but they were not available locally and I did not want to wait.

When I say they would not pump up , I mean you remove valve cover while motor is warm and you are able to lift the rocker arm on the valve with the bad lifter and collapse the plunger. New ones all pop up except what I notice now in the morning after the motor ran last making the noise, the lifters (Not sure how many) are loose and tap for 20 seconds or so. So I think the lifters are not getting enough oil. I really believe this .
69 customcamper is offline   Reply With Quote
Old 07-30-2020, 11:37 AM   #19
gmc684x4
Registered User
 
Join Date: Jul 2012
Location: Whitehorse yukon
Posts: 1,218
Re: 396 experts need help

Did you re break in the new lifters after you changed them ?
gmc684x4 is offline   Reply With Quote
Old 07-30-2020, 11:38 AM   #20
j_cst_10
Senior Member
 
j_cst_10's Avatar
 
Join Date: Nov 2008
Location: Cleveland, OH
Posts: 575
Re: 396 experts need help

I would adjust using the procedure I outlined so you know exactly where they are. Move the pushrod up and down and tighten until you feel zero lash. Then 1/2-1 turn after.
__________________
1972 Cheyenne Super 20 Custom Camper 12 Valve Cummins/5spd manual
1972 Cheyenne Super Short Bed 557 Med Olive DK olive
1970 K5 Blazer Dark Gold

1966 Coronet 440 35k mile survivor
1991 Suburban 2500 454/4L80E 2wd
1985 Monte Carlo SS 383 Sbc, t-56 magnum 6spd and Ford 9"
j_cst_10 is offline   Reply With Quote
Old 07-30-2020, 11:48 AM   #21
Boog
laying low
 
Boog's Avatar
 
Join Date: Mar 2001
Location: Searcy, Ark. USA
Posts: 12,888
Re: 396 experts need help

That sounds an awful lot like the lifter issue the early 454's had. After warm up lifter clack appeared and this was with a stock engine. Oil pressure was good but it clacked after warm up. Usually it was on cylinder #1. The GM fix was to drill a small hole in the lifter galley plug at the front of the block next to #1 cylinder to let the hot oil out and fresh oil into the lifters. Dad and I drilled his to cure his lifter clack after having replaced those lifters several times. No more problems. There was a service bulletin back then so this information came from GM in the early 70's.
__________________
Boog
69 Chevy stepside, 358/T350, 4.11 posi, 4.5/4 drop, rallys, poboy driver
primer is finer
91 Chevy sportside, Tahoe, Yukon & GMC Crewcab All GM..'nuff said.

I stand for the flag and kneel at the cross
Boog is offline   Reply With Quote
Old 07-30-2020, 11:50 AM   #22
kwmech
Senior Member
 
Join Date: Mar 2003
Location: Colfax-California
Posts: 8,355
Re: 396 experts need help

I have the same issue with my 454 with the nuts not holding adjustment and slowly backing off. I just bought a new set of nuts and will swap them out and adjust this weekend. I think the ones that came with the rockers may be junk chinese who knows. I have the comp cams roller tip rocker set
kwmech is online now   Reply With Quote
Old 07-30-2020, 02:15 PM   #23
weim55
Registered User
 
Join Date: Jan 2017
Location: Larkspur, Colorado
Posts: 904
Re: 396 experts need help

I wish I could give you some sound advice but honestly it’s so difficult to discern these issues without actually being in front of the engine and hearing it. I can tell you what my recent experience is although it’s a bit discouraging. I will no longer do any engine rebuilds for customers anymore. I have done More small and big block Chevy’s then I can count for decades prior without issue but in the last five years replacement parts in the supply chain have become so bad and unreliable I can no longer put together an engine I can stand behind because of it. I can think of 4 engines in the last five years I have had a hand in that have the exact problem you are speaking of. Noisy lifters when the engine is hot. In my personal opinion I really believe it is defective lifters in every case but I do not have definitive proof.

Steve weim55 Colorado
weim55 is offline   Reply With Quote
Old 08-01-2020, 04:40 PM   #24
69 customcamper
Registered User
 
Join Date: Aug 2018
Location: Glendale CA
Posts: 122
Re: 396 experts need help

Quote:
Originally Posted by weim55 View Post
I wish I could give you some sound advice but honestly it’s so difficult to discern these issues without actually being in front of the engine and hearing it. I can tell you what my recent experience is although it’s a bit discouraging. I will no longer do any engine rebuilds for customers anymore. I have done More small and big block Chevy’s then I can count for decades prior without issue but in the last five years replacement parts in the supply chain have become so bad and unreliable I can no longer put together an engine I can stand behind because of it. I can think of 4 engines in the last five years I have had a hand in that have the exact problem you are speaking of. Noisy lifters when the engine is hot. In my personal opinion I really believe it is defective lifters in every case but I do not have definitive proof.

Steve weim55 Colorado

The chinese and taiwan parts are total Garbage. That is correct.
69 customcamper is offline   Reply With Quote
Old 08-02-2020, 08:31 AM   #25
Ironangel
Senior Member
 
Ironangel's Avatar
 
Join Date: Feb 2010
Location: Falls City, Nebraska "100 Miles From Nowhere"
Posts: 2,219
Re: 396 experts need help

Quote:
Originally Posted by geezer#99 View Post
Of course the cam looked fine. Lifters and cam wear in togethor.
Changing the lifters likely changed that.

Pop the valve covers off and check all the rockers are moving the same.
This! And I'll add checking with your eyeball is a crude method, use a dial indicator to measure the lift! Only then can you rest assured that all lobes are good, it only takes one bad lifter to wipe out it's lobe. I've had out of the box lifters that failed to pump up because they were failing to collapse presenting zero preload! The Asian machining processes are questionable at best and should never be trusted!
__________________
Michael of the clan Hill,
"Two Seventy Two's"
71 1-ton Dually 350 4-Speed
71 C/50 Grain Truck, 350 Split-Axle 4-Speed
02 3/4 ton Express
14 Indian Chief Vintage
1952 Ford 8N, "Only Ford Allowed On The Property"
"Be American, Buy American"
Ironangel is offline   Reply With Quote
Reply

Bookmarks

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT -4. The time now is 11:13 AM.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Copyright 1997-2022 67-72chevytrucks.com