Project Roxy - Page 8 - The 1947 - Present Chevrolet & GMC Truck Message Board Network

sduckworth13 · 01-23-2013, 11:53 PM

How's the truck coming along?

Rochlow · 01-24-2013, 12:04 AM

Wish I had some progress to report, but between the holidays and overtime all this month I haven't been in the garage in over a month. Next month isn't looking good either. I'm hoping to be back on it by end of February.
Posted via Mobile Device

sduckworth13 · 01-24-2013, 12:08 AM

Good to hear

Rochlow · 01-31-2013, 12:02 AM

Not sure how important the pinch weld/ toe/ floor board seam is? But I got impatient monkey around with all the rust in mine. Had to put a new floor pan in, so I just butt welded the floor pan to the toe board. I know it's not factory. But it seems that the rust occurs because of all the seam seal stuffed there.

Posted via Mobile Device

sduckworth13 · 01-31-2013, 12:08 AM

Looks good, You know its solid now, it won't need to be replaced for a long time.

Rochlow · 02-10-2013, 07:54 PM

sduckworth13 · 02-10-2013, 09:28 PM

Nice job on the speaker grill.

sduckworth13 · 02-10-2013, 09:30 PM

looks like a vintage air unit is calling too, nice work

Rochlow · 02-10-2013, 10:24 PM

Thanks for the compliment. Maybe air some day, but no a/c or heat in the immediate future.
Posted via Mobile Device

sduckworth13 · 02-10-2013, 10:30 PM

I think I will be doing the same to my firewall, all these mods I'm planning are starting to add up. I originally was just doing a simple 4.5/6 inch drop.
Posted via Mobile Device

Rochlow · 02-10-2013, 10:57 PM

Yea, this old trucks seem to steamroll if your not careful.. I was just going to swap my v8 and Porterbuilt suspension on this one.. Cab made that come to a halt..
Posted via Mobile Device

67c10rustbuket · 02-11-2013, 11:16 AM

Looking great man! Nice job on the rust repairs.

You know I put the flange on my floor pan using a hydraulic press brake at work, thinking I was pretty slick... well forming the whole flange at once pulled some of the contour out of the front where it goes down toward the kick panel so I had to cut and reshape that.

I really wish they made the floor pan with that flange on them.

aggie91 · 02-11-2013, 12:03 PM

I just went thru this build. I am tuning is for the rest...

Bennett68C10 · 02-11-2013, 12:48 PM

Patchwork on the floor looks good, I had to repair mine in about the same exact way.

Rochlow · 02-11-2013, 01:17 PM

Quote:

Originally Posted by 67c10rustbuket

Looking great man! Nice job on the rust repairs.

You know I put the flange on my floor pan using a hydraulic press brake at work, thinking I was pretty slick... well forming the whole flange at once pulled some of the contour out of the front where it goes down toward the kick panel so I had to cut and reshape that.

I really wish they made the floor pan with that flange on them.

That flange/pinch weld is a PITA and it seems that every cab that I've had or looked at rotted out right there.

Last_Paladin · 02-12-2013, 09:19 AM

Quote:

Originally Posted by Rochlow

That flange/pinch weld is a PITA and it seems that every cab that I've had or looked at rotted out right there.

Mine is mostly cut away to clear the 6L90E.

**Hart_Rod** · 02-12-2013, 09:55 AM

Quote:

Originally Posted by Last_Paladin

Mine is mostly cut away to clear the 6L90E.

What motor mounts are you using and do you have pictures of how close your motor is to the firewall?

Last_Paladin · 02-12-2013, 10:00 AM

Quote:

Originally Posted by Hart_Rod

What motor mounts are you using and do you have pictures of how close your motor is to the firewall?

Sorry, I do not. I also don't want to hi-jack this build thread

PBFAB.COM · 02-12-2013, 11:55 AM

Looking good Jeff! That's a lot of work!

Rochlow · 02-12-2013, 01:35 PM

Quote:

Originally Posted by Porterbuilt Street Rods

Looking good Jeff! That's a lot of work!

Thanks, Nate!

Rochlow · 04-07-2013, 08:44 PM

Posted via Mobile Device

VA72C10 · 04-07-2013, 09:02 PM

Looks good!

Bennett68C10 · 04-07-2013, 10:57 PM

Nice work, glad to see some updates. Did you use the boom mat on the floor.
Posted via Mobile Device

Rochlow · 04-08-2013, 06:56 AM

Quote:

Originally Posted by Bennett--G4L

Nice work, glad to see some updates. Did you use the boom mat on the floor.
Posted via Mobile Device

Yes I did. I really like how easy it is to use.
Posted via Mobile Device

Rochlow · 04-21-2013, 02:34 PM

Posted via Mobile Device

01-23-2013, 11:53 PM	#176
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Project Roxy How's the truck coming along? __________________ Scott

01-24-2013, 12:04 AM	#177
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy Wish I had some progress to report, but between the holidays and overtime all this month I haven't been in the garage in over a month. Next month isn't looking good either. I'm hoping to be back on it by end of February. Posted via Mobile Device

01-24-2013, 12:08 AM	#178
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Project Roxy Good to hear __________________ Scott

01-31-2013, 12:02 AM	#179
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy Not sure how important the pinch weld/ toe/ floor board seam is? But I got impatient monkey around with all the rust in mine. Had to put a new floor pan in, so I just butt welded the floor pan to the toe board. I know it's not factory. But it seems that the rust occurs because of all the seam seal stuffed there. Posted via Mobile Device

01-31-2013, 12:08 AM	#180
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Project Roxy Looks good, You know its solid now, it won't need to be replaced for a long time. __________________ Scott

02-10-2013, 07:54 PM	#181
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy

02-10-2013, 09:28 PM	#182
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Project Roxy Nice job on the speaker grill. __________________ Scott

02-10-2013, 09:30 PM	#183
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Project Roxy looks like a vintage air unit is calling too, nice work __________________ Scott

02-10-2013, 10:24 PM	#184
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy Thanks for the compliment. Maybe air some day, but no a/c or heat in the immediate future. Posted via Mobile Device

02-10-2013, 10:30 PM	#185
sduckworth13 Registered User Join Date: Mar 2011 Location: Kansas City, Missouri Posts: 3,541	Re: Project Roxy I think I will be doing the same to my firewall, all these mods I'm planning are starting to add up. I originally was just doing a simple 4.5/6 inch drop. Posted via Mobile Device __________________ Scott

02-10-2013, 10:57 PM	#186
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy Yea, this old trucks seem to steamroll if your not careful.. I was just going to swap my v8 and Porterbuilt suspension on this one.. Cab made that come to a halt.. Posted via Mobile Device

02-11-2013, 11:16 AM	#187
67c10rustbuket Registered User Join Date: Apr 2011 Location: Mustang, Oklahoma Posts: 2,807	Re: Project Roxy Looking great man! Nice job on the rust repairs. You know I put the flange on my floor pan using a hydraulic press brake at work, thinking I was pretty slick... well forming the whole flange at once pulled some of the contour out of the front where it goes down toward the kick panel so I had to cut and reshape that. I really wish they made the floor pan with that flange on them. __________________ Dan <---(my name) 67 SWB C10 project "GEORGIA"-59 Brookwood 2dr wag...Next project-03 Tahoe 4x4 5.3 family ride-07 Hondur Accord, commuter car

02-11-2013, 12:03 PM	#188
aggie91 I'm just glad to be here! Join Date: Jan 2008 Location: Longview, TX Posts: 4,788	Re: Project Roxy I just went thru this build. I am tuning is for the rest... __________________ Karl 1965 Chevy Stepside(Grandpa's Old Blue) and (July 2015 Shop Build!)(2020, the Saga Continues) http://67-72chevytrucks.com/vboard/s...d.php?t=372424 The LST Challenge: http://67-72chevytrucks.com/vboard/s...=1#post7812257 Korbin's 1st Square: "Sunburn" http://67-72chevytrucks.com/vboard/s...d.php?t=418618 1985 GMC Sierra: "White Trash", Korbin's 2nd now... http://67-72chevytrucks.com/vboard/s...d.php?t=632305 Henry - 1984 Chevrolet, Owen's 1st Square

02-11-2013, 12:48 PM	#189
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Project Roxy Patchwork on the floor looks good, I had to repair mine in about the same exact way. __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10

02-12-2013, 11:55 AM	#194
PBFAB.COM Senior Member Join Date: Dec 2003 Location: Mesa,Az Posts: 3,981	Re: Project Roxy Looking good Jeff! That's a lot of work! __________________ www.PorterbuiltFabrication.com Phone: 480-297-2621 E-mail: sales@pbfab.com Find us on FaceBook under Porterbuilt Fabrication Specializing in Chassis and Suspension Components for your Classic Chevrolet Truck. We offer components from the following manufacturers: Porterbuilt Accuair Ridetech (Air Ride Technologies) Air Lift Wilwood Intro Unisteer ECE Gotta Show Air Lift Borgeson CPP Supporting this forum since 2003!



Register or Log In To remove these advertisements.

04-07-2013, 08:44 PM	#196
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy Posted via Mobile Device __________________ ///Relaxed Atmosphere

04-07-2013, 09:02 PM	#197
VA72C10 VA72C10 Join Date: Mar 2008 Location: Midlothian, VA Posts: 25,269	Re: Project Roxy Looks good! __________________ Looking for a 67-72 swb or blazer project in or around VA.

04-07-2013, 10:57 PM	#198
Bennett68C10 Registered User Join Date: Dec 2006 Location: Toms River, NJ Posts: 5,518	Re: Project Roxy Nice work, glad to see some updates. Did you use the boom mat on the floor. Posted via Mobile Device __________________ Keith 66 Suburban Burb Build Thread: http://67-72chevytrucks.com/vboard/s...d.php?t=751361 IG: bennett68c10

04-21-2013, 02:34 PM	#200
Rochlow Registered User Join Date: Aug 2006 Location: St. Albans, Vt Posts: 2,520	Re: Project Roxy Posted via Mobile Device __________________ ///Relaxed Atmosphere

Register or Log In To remove these advertisements.