i need some recomendations

[bigmalc]

i have a 90 suburban and looking to drop it approxiamately 4/5 inches in the front and 6/7 in the rear what do you suggest i use?
Posted via Mobile Device

[hellbent72]

Front 3inch drop spindle and 2 inch drop spring or 2 1/2 spindle and 2 1/2 drop spring. Rear 4 inch drop hanger and remove a leaf spring or two. As well as a bolt in c notch
Posted via Mobile Device

[bigmalc]

What website can I order those hangers and drop spindles. This is my first project that I'm doing the suspension on
Posted via Mobile Device

[tinydb84]

Originally Posted by hellbent72

Front 3inch drop spindle and 2 inch drop spring or 2 1/2 spindle and 2 1/2 drop spring. Rear 4 inch drop hanger and remove a leaf spring or two. As well as a bolt in c notch
Posted via Mobile Device

I dont think they make drop hangers that large and if they did it would throw your pinion so far off you would vibrate down the road.

[bigmalc]

i havent had any luck in finding hangers that would lower it that low what about a flip kit?
Posted via Mobile Device

[tinydb84]

Drop hangers and shackles together will get your 4 inches. To get 6 you can do a flip kit. To get 7 you can do a flip kit and shackle.

[bigmalc]

Do you have a link where I can order them from
Posted via Mobile Device

[tinydb84]

http://www.ebay.com/itm/1973-1987-C1...44b997&vxp=mtr

then cut a coil off the front springs

[lolife99]

Originally Posted by tinydb84

http://www.ebay.com/itm/1973-1987-C1...44b997&vxp=mtr

then cut a coil off the front springs

Are you sure the burbs and pickups have the same type front hanger???

[lolife99]

A truck flip kit will get you in your 6"-7" rear drop range,... but you will need a c-notch and sheetmetal mod to the floor to keep the center section of the rearend off the floor.

My old '91 burb had 4" drop leaf springs and the rearend was close to hitting on large bumps.

[tinydb84]

Originally Posted by lolife99

Are you sure the burbs and pickups have the same type front hanger???

That link is for a flip kit not shackles/hangers

As for the hangers I have no clue

[bigmalc]

Originally Posted by lolife99

A truck flip kit will get you in your 6"-7" rear drop range,... but you will need a c-notch and sheetmetal mod to the floor to keep the center section of the rearend off the floor.

My old '91 burb had 4" drop leaf springs and the rearend was close to hitting on large bumps.

the burban is sitting nice i need that set up
Posted via Mobile Device

[lolife99]

Originally Posted by tinydb84

That link is for a flip kit not shackles/hangers

As for the hangers I have no clue

I was using my phone.
I had shackle/hanger drop on my mind.
Sorry.

If you do a flip kit,... stick with Belltech or Western Chassis or McGaughy's.
They have a better designed flip kit bracket.

[bigmalc]

thanks i seen a belltech set up on autoanything im gonna probably go with and its a 4/6
Posted via Mobile Device

[blazins10]

my 90 burb had the belltech spindals , cut coils , flip kit with helper bags
and sat nice and drove great , will do the same with my next one
Posted via Mobile Device

[bigmalc]

Did you change out the shocks also?
Posted via Mobile Device

[blazins10]

I ram some stock Replacement kybs
Posted via Mobile Device