NJ Suburban

[richard2717]

Looking good Paul. Did you find the inner 1/4 pc. you were looking for? I just picked up 2 parts burbs and I will check them out to see if either has a decent pc. if you are still in need. Pending snow this evening may hang me up a little but i will check 1st chance I get if you do need it.

Richard

[Hart_Rod]

Nice progress.

[pwdcougar]

Originally Posted by richard2717

Looking good Paul. Did you find the inner 1/4 pc. you were looking for? I just picked up 2 parts burbs and I will check them out to see if either has a decent pc. if you are still in need. Pending snow this evening may hang me up a little but i will check 1st chance I get if you do need it.

Richard

Richard one is on its way from Randy500. Thanks for thinking of me!

Paul

[zicc1835]

looking good

[pwdcougar]

Originally Posted by Hart_Rod

Nice progress.

Thanks guys!

Glad it is inside now so it can get some work done!

Paul

[pwdcougar]

More bodywork. With the mild winter here in NJ the usual 5 snowblower repairs a week I saw last year are non existent this year. The plus is lots of Suburban time in the garage.

The inner part 3rd door rocker that is part of the floor was a pain to fabricate. Glad I saved the entire roof of my original Suburban for sheet metal repair material. This weekend I'll paint everything inside with either POR15 or epoxy primer and then weld on the outer rocker and the quarter panel patch!

Paul

[pwdcougar]

All the treated rust and homemade patch panel primed with KBS. I need to collect the door from storage and re hang it before welding in the new rocker and lower quarter piece. I'm sure my storage garage isn't plowed out yet! We got about 8" here in NJ last night. I'm loving my garage heater!

Paul

[Average Joe]

Nice work!

[zicc1835]

staying warm making progress looks great Paul

[pwdcougar]

And more progress! Welded in the quarter patch. Once it is epoxy primed and seam sealed I'll weld in the rocker.

Paul

[richard2717]

Moving right along, looking good. I can't seem to find time to work on any of mine, too busy cutting up parts trucks.

Was this pretty much the bulk of the metal replacement or do you need to do driver side as well?

Richard

[pwdcougar]

Richard both front rockers still need to be done as well as the driver side lower quarter. There is still a long way to go! I got the rocker inner and outer panels but they will need a lot of fabricating since they are pickup parts. The door had to come out of storage so that I could match up the body lines. Spent all morning fussing with the alignment!

Paul

[Bigdav160]

I was going to say, the door alignment looked better than factory. Good job.

I should ask, does that patch have the bead edge or no?

I bought a slightly larger patch and it has the beaded edge but the rest of the wheel arch patch does not. I am trying to figure out how I am going to make it look right.

[pwdcougar]

Dave the beaded edge matches the factory edge pretty well. I saw your post with your patch and the issues you are having. I think the wheel arch patch that LMC sent has the beaded edge but I'll have to check. Years from now I hope I have the patience to align the door again!

Paul

[pwdcougar]

Got the panels welded in epoxy primed and seam sealed. Tomorrow I'll shoot the sanding primer. I've got some warpage in the rear quarter but I'm really happy with the panel fit.

Paul

[goldenburb]

LOOKING GOOD Paul
post good notes cause Ill be needing all the reference I can find. lol

[pwdcougar]

Wow it's been a while!

Got some work done on the front right side this past week. It will get a coat of epoxy primer before the rocker goes on.

Paul

[zicc1835]

looks good Paul i been making some progress myself ...you around this weekend come get my saw

[Csrock82]

Nice job on the repairs.

[pwdcougar]

Originally Posted by Csrock82

Nice job on the repairs.

Thanks! Made a little more progress. The right side is done. Time to turn it around and work on the left side now!

Paul

[04ls1gto]

Originally Posted by pwdcougar

Thanks! Made a little more progress. The right side is done. Time to turn it around and work on the left side now!

Paul

Looks great, how many hrs did you have in rocker replacement? All 3 of mine are gonna need to get done. Maybe next Winter

[Killer Bee]

great work Paul!! thanks for the recent chat, helped me out a bunch!

I chickened out though and found a very little rust Fremont burb a couple of hours from here..

seller and I worked out a real fair deal and I think we both did good..

I'll get a thread going sometime to share with everyone as I move out of 'ol rusty blue..

please keep up the good work in the fight against rust and keep us all posted!

[pwdcougar]

Originally Posted by 04ls1gto

Looks great, how many hrs did you have in rocker replacement? All 3 of mine are gonna need to get done. Maybe next Winter

GTO I’ve got way to many hours in this. The front rockers are tough because you have to modify a truck rocker.


Paul

[pwdcougar]

Getting ready to prep and prime the cowl and windshield area. The plan for the rust on the window frame is to treat and paint it with POR 15 and hit it with the Omni epoxy primer while the POR is still tacky. It's already been wire brushed with my 4" and die grinders.

Paul

[Average Joe]

Nive work!

I am dreading pulling my windshield. I know there is some rust. I just hope it doesnt require too much surgery.