The 1947 - Present Chevrolet & GMC Truck Message Board Network

The 1947 - Present Chevrolet & GMC Truck Message Board Network (https://67-72chevytrucks.com/vboard/index.php)

- 4x4 Projects and Builds (https://67-72chevytrucks.com/vboard/forumdisplay.php?f=141)

- - Crash's 69 K10 (https://67-72chevytrucks.com/vboard/showthread.php?t=494599)

Re: Crash's 72 K10

Looks like you have a plan to fix the bed. Your blaster works great. I need to get one of those as much as I hate blasting......

It was good to finally get to see your build in person. The pictures don't do justice to how good it really looks in person. You have a top notch build going. This truck will be super nice when done. Don't sweat the progress.
This time of year is lake time.....

Re: Crash's 72 K10

Quote:

Originally Posted by Gardnervillain (Post 5422570)

Wow! Great build! I wanted to know if you made your own fuel cell or purchased it? Also, it appears that it hangs a little lower than the tank you had before. I'm trying to decide which way to go as we have a rear tank from a Suburban we can use, but I love the look of your new one.

Thanks... I did not build the fuel cell, I am not that good. It was build by Boyd Welding, they have thread in the vendor section of this site. It may hang a little lower, but I have lots of room under there :cool:

Have a great day..

Re: Crash's 72 K10

Quote:

Originally Posted by hgs_notes (Post 5422860)

Check out page 26 of the LMC online catalog, part #38-9628. Kind of pricey for a patch, but the only one I know of available other than buying the small bed floor patches (which don't have the rib ends) or a new floor. You can use the middle sections of another truck bed floor, but fing one that is not hammered bad or rusted can be a challenge because usually it won't be available to cut up. I had some pieces of a blazer bed floor from one I parted out and I made some with just flat sheetmetal for small spots.

Thanks.. Yes, I have seen that one, and I may have to buy it, but I want to see if I can come up with a cheaper fix. You are right about the edge being rolled, that will be hard to duplicate.

Once again thanks...

Re: Crash's 72 K10

Quote:

Originally Posted by mcbassin (Post 5422919)

Thanks Mike, I have a plan, but I have to figure out what to do about the patch. I can buy a peice with the rolled edge, but cost is a factor, or I can buy a cheap patch and somehow come up with a way to roll the edge..

Thanks for the comments on the truck, it does not look as good as yours.. My hand brush paint job on the frame has a few runs... Right now I am just hoping to have it look good at 15 to 20ft ... lol.

Your right about the summer, it is lake time...

Have a great weekend....

Re: Crash's 72 K10

Quote:

Originally Posted by Crash_OK (Post 5423815)

Thanks, I'm just finding my way around this forum. I wish I would have found it before I started digging in last year. Your thread has been especially helpful -- thanks for taking the time to keep us all updated.

Re: Crash's 72 K10

Hey Crash,you're looking good on cleaning up the bed.All your repaired work on the rest of the truck has been a job well done.I think you have master the rust repair.Keep up the hard work & keep on truckin' :metal: :cool:

Re: Crash's 72 K10

Quote:

Originally Posted by RCbowtie69 (Post 5425087)

Thanks, not sure I have mastered anything, but I do feel better about attacking rust in the future... have a great day..

Re: Crash's 72 K10

Re: Crash's 72 K10

Very nice! It looks like the cab fits like a glove. It must have felt like a huge accomplishment to have all those parts mounted up. At least there is light at the end of the tunnel. Can't wait to get my cab painted and back on for good.

Did you consider mounting the computer behind the engine like 68 short step does on his builds? It will get the computer out of sight. Not sure about your clearence?

Re: Crash's 72 K10

Quote:

Originally Posted by mcbassin (Post 5440899)

Thanks Mike.. I still have a lot of work to do. I have thought about behind the engine, but there does not appear to be enough room. I think I can mount it all on the fender well and make it look decent. It is just an old farm truck you know...

When you painting yours?

Re: Crash's 72 K10

Congrats on the cab work Mark! you did an awesome job on the rust removal and finally won the battle. You worked like a machine on that and make me feel lazy at times, but in a motivational way ;).

If I remember correctly GMC pauls carries Tri Plus/key parts body panels which you can buy in person at classic auto located at 89th and I35 (moore/OKC border) so no shipping there. i have a fender from there but I only test fitted it before tear down and all my panels where pretty off as far as alignment goes. Maybe call GMC pauls and Classic and ask them which brand steel parts they are using but I am pretty sure both sell Tri plus.

For inner fenders a friend at work bought his for a 72 from certi fit in okc, they are lower quality panels but he said they fit great and they are only like $59 each. He also bought his fenders there and they look good and line up pretty nice but they are thinner than tri plus versions.

also with these Oklahoma stores you can actually return stuff if you are unhappy with the fit.

Re: Crash's 72 K10

Quote:

Originally Posted by 67c10rustbuket (Post 5441524)

Thanks for the comments and the leads on the body parts... I still may go with the GMCPauls doors... but I will call Classic first...
Once again thanks...

Re: Crash's 72 K10

very nice job looks great

Re: Crash's 72 K10

Very nice work , I am doing a 70 c10 that's taking alot of my time , but being a mechanic an body guy for over 25 years I want to do it right the first time . I'm getting close to paint ,:metal: hats off to you ... should be a Great truck when done

Re: Crash's 72 K10

Quote:

Originally Posted by bchaney (Post 5463592)

very nice job looks great

Thank you...

Re: Crash's 72 K10

Quote:

Originally Posted by c10327 (Post 5463779)

You are a rare breed both mechanc and Body Guy.. I don't see how the body guys/gals do it.. it takes so long...

Good luck with your build

Re: Crash's 72 K10

Crash_ok...I love this build!
Posted via Mobile Device

Re: Crash's 72 K10

Very nice progress Mark! I'm glad you're figuring out all the wiring mods. That way when I get ready to mine, you can walk me through it :)

Re: Crash's 72 K10

WOW I have been watching/reading your build thread, nice work and fast too,I like the modern engine and trans use. I have a 70K10 Lwb that I will be building as soon as I get done with a few other projects . I have decided after following your build that I too will use a modern powertrain setup. Everything looks great. I have a question or two if you don't mind? the trans you are using is a 4 speed correct? next are you planning on using the stock column? it is setup for a 3 speed trans. I went to to Costco today and was thinking about that as I drive an 08 Z71 silverado 4X4 with the same trans I think and I just got to thinking!!
keep up the good work.

Re: Crash's 72 K10

Very, very nice job! Cool to see another okie building a SWB 4x4!

Re: Crash's 72 K10

Very nicely done wip. Great scores on the sand blaster and press. Nice to see this rig coming back to life again and all the faults being corrected like that crooked crossmember. Golf cart looks very sharp too btw.

Re: Crash's 72 K10

Very nice work on the wiring and mounts. I like what you have going Mark. Keep the updates coming.
Posted via Mobile Device